Starting from mac80211 commit adf8ed01e4fd ("mac80211: add an optional
TXQ for other PS-buffered frames") and commit 0eeb2b674f05 ("mac80211:
add an option for station management TXQ") a new per-sta queue has been
introduced for bufferable management frames.
sta->txq[IEEE80211_NUM_TIDS] is initialized just if the driver reports
the following hw flags:
- IEEE80211_HW_STA_MMPDU_TXQ
- IEEE80211_HW_BUFF_MMPDU_TXQ
This can produce a NULL pointer dereference in mt76_stop_tx_queues
since mt76 iterates on all available sta tx queues assuming they are
initialized by mac80211. This issue has been spotted analyzing the code
(it has not triggered any crash yet)
Signed-off-by: Lorenzo Bianconi <[email protected]>
We always wait for CMD_CALIBRATION_OP mcu message, but wait argument is used
for do additional MT_MCU_COM_REG0 register operations, which are needed
for mt76x2e devices and we can use appropriate check instead of wait argument.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Initialize bss_info_changed mac80211 callback to
mt76x02_bss_info_changed utility routine and remove duplicated code.
Use 8 as WCID index for sta interface
Signed-off-by: Lorenzo Bianconi <[email protected]>
Perform channel calibration after each channel switch and not only after
connection establishment since NetworkManager perform multiple frequency
scanning if RSSI in lower a given threshold
Signed-off-by: Lorenzo Bianconi <[email protected]>
Add MCU_CAL_TX_SHAPING calibration in mt76x2u_phy_channel_calibrate
routine since now mt76x2 and mt76x2u driver run the same firmware
Signed-off-by: Lorenzo Bianconi <[email protected]>
Add mt76x02_config_mac_addr_list routine in order to set
the mac address list supported by the driver. Initialize
wiphy->addresses/n_addresses for mt76x0e driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
If there are still pending packets in the tx queue when removing a station,
it could possibly lead to a call to further attempts to pull packets from
the mac80211 tx queue after it has already been removed from the scheduling
list.
Prevent this from happening by calling synchronize_rcu after deleting the
wcid pointer before further cleaning up the tx queues.
To be extra careful, ensure that mtxq->list is always initialized properly.
Also drop the useless call to mt76x02_mac_wcid_setup, which only re-assigns
the bss index of the wcid entry, but does not help with the cleanup in any
way.
Signed-off-by: Felix Fietkau <[email protected]>
Fix forcing watchdog reset after a MCU hang
Run watchdog work immediately after a failed channel change
Signed-off-by: Felix Fietkau <[email protected]>
Add support for parsing legacy rates, use a flag in the tx status info
as indicator for fixed rate packets
Signed-off-by: Felix Fietkau <[email protected]>
The FIXED_RATE flag of txd6 does not enable fixed rate, it only configures
the use of the fixed rate register as rate source.
Set the right flag in txd2 instead.
Signed-off-by: Felix Fietkau <[email protected]>
So far the code only validates the buffer size of the first skb.
Extend this check to cover additional fragments as well, in case the size
is corrupted during a DMA reset.
Signed-off-by: Felix Fietkau <[email protected]>
Use 4096 as maximum size instead of the rx buffer size, since rx packets
can be split across multiple buffers. This fixes issues with receiving
A-MSDU aggregated packets.
Signed-off-by: Felix Fietkau <[email protected]>
There is some code in the mac80211 tx status processing code that could
potentially call back into the tx codepath.
To avoid deadlocks, make sure that no tx related spinlocks are taken
during the ieee80211_tx_status call.
Signed-off-by: Felix Fietkau <[email protected]>
Fix IBI_R11 configuration on non-radar channels for mt76x0e
driver. This patch improve system stability under heavy load.
Moreover use IBI_R11 name and remove magic numbers for
0x212c register
Fixes: 0c3b3abc9251 ("mt76x0: pci: add DFS support")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Assure that after we initialize dev->cal.low_gain to -1 this
will cause update gain calibration. Otherwise this might or
might not happen depending on value of second bit of low_gain
and values read from registers in mt76x02_phy_adjust_vga_gain().
Signed-off-by: Stanislaw Gruszka <[email protected]>
If we are associated and scanning is performed, sw_scan_complete callback
is done after we get back to operating channel, so we do not perform
queue cal work. Fix this queue cal work from sw_scan_complete().
On mt76x0 we have to restore gain in MT_BBP(AGC, 8) register after
scanning, as it was multiple times modified by channel switch code.
So queue cal work without any delay to set AGC gain value.
Similar like in mt76x2 init AGC gain only when set operating channel
and just check before queuing cal work in sw_scan_complete() if
initialization was already done.
Fixes: bbd10586f0df ("mt76x0: phy: do not run calibration during channel switch")
Signed-off-by: Stanislaw Gruszka <[email protected]>
Remove wait argument from mt76x02_mcu_set_radio_state and newer wait
for response when sending CMD_POWER_SAVING_OP mcu command.
Note this change behaviour for PCIe devices, but the change is in
align with vendor driver.
Signed-off-by: Stanislaw Gruszka <[email protected]>
