Add mt76x2_mac_load_tx_status routine since tx stats register map is
shared between usb and pci based devices but usb devices do not have a
tx stat irq line as pcie ones and it is necessary to load tx statistics
using a workqueue
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Move wiphy interface_modes definition in mt76x2_init in order to
reuse mt76_register_device routine supporting mt76x2u based chipsets
since mt76x2u currently supports just sta mode
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Add mt76x2_init_device routine in order to reuse common pcie/usb mac80211
initialization code supporting mt76x2u based device
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
In order to reuse them supporting mt76x2u based devices, move
mt76x2_wait_for_mac, wait_for_wpdma and mt76x2_channel_silent in
mt76x2.h
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
move mt76x2_fw_header and mt76x2_patch_header definitions in mcu.h in
order to reuse them in mt76x2u mcu related code
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Since MT_TXD_INFO, MT_MCU_MSG and MT_RX_FCE_INFO definitions are in
common between mt76x2u, mt76x2 and mt76x0u move them in dma.h in order
to reuse usb code supporting mt76x2u and mt76x0u based devices
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Add sw pattern detector statistics to mt76x2 debugfs.
Moreover track down number of allocated sequence by the detector
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Add sw DFS pattern detector support for mt76x2 based devices.
Dfs pattern supported:
- short pulse radar patterns
- staggered radar patterns
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Introduce sw event ring buffer to queue DFS pulses loaded from the hw.
Radar pulses will be used in DFS sw detector
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Add mt76_{incr,decr} utility routines to increment/decrement a value
with wrap-around (they will be used by mt76x2 DFS sw detector)
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Fix mcs and attempt count estimation in mt76x2_mac_fill_tx_status routine
if the number of tx retries reported by the hw is grater than
IEEE80211_TX_MAX_RATES
Fixes: 7bc04215a66b ("mt76: add driver code for MT76x2e")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Despite this issue is not harmful since it is not actually used in
mt76 driver, fix DMA txinfo bitmask definition
Fixes: 7bc04215a66b ('mt76: add driver code for MT76x2e')
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Remove unnecessary break statement in the default case of bw switch
block in mt76x2_mac_process_tx_rate routine
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
It is no longer necessary for client mode operation, vif index entries
8-16 are no longer used
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Since channel active time is not available from MIB registers, emulate it
using the kernel boot time (in us)
Signed-off-by: Felix Fietkau <[email protected]>
Use 11M as tx rate for CCK protection control frames
Fixes: 7bc04215a66b ("mt76: add driver code for MT76x2e")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Using the NAPI or netdev frag cache along with other drivers can lead to
32 KiB pages being held for a long time, despite only being used for
very few page fragments.
This can happen if the driver grabs one or two fragments for rx ring
refill, while other drivers use (and free up) the remaining fragments.
The 32 KiB higher-order page can only be freed once all users have freed
their fragments.
Depending on the traffic patterns, this can waste a lot of memory and
look a lot like a memory leak.
Signed-off-by: Felix Fietkau <[email protected]>
When switching between low gain (high RSSI) and high gain settings, it
can take a few seconds to adjust to the current environment.
This can lead to short periods of time with extreme packet loss.
When switching from low_gain=1 to low_gain=2, start with the same gain
adjustment value instead of the lowest to avoid spikes of huge numbers
of false CCA events
Also avoid resetting adjustment values on switching between low_gain
values 0 and 1, since it affects only the upper limit of vga adjustment
Signed-off-by: Felix Fietkau <[email protected]>
The range should only be limited to 4 for really weak signals, for all
other gain settings the range is 16.
Signed-off-by: Felix Fietkau <[email protected]>
usleep_range can cause excessive latency on channel change if waiting
for the MAC to stop fails. It will be forced to stop by the code
following that loop anyway.
Signed-off-by: Felix Fietkau <[email protected]>
During scans, mac80211 frequently switches back to the home channel to
minimize interruption of ongoing traffic. Keep regular tx queues active
during that time.
Signed-off-by: Felix Fietkau <[email protected]>
The beacon timer drifts by 1 microsecond every TBTT. After 20 minutes
with a beacon interval of 100, the drift will be almost 12 ms, enough to
cause weird issues for devices in powersave mode.
Since the beacon timer is configured in units of 1/16 TU (64 us), we
need to adjust it once every 64 beacons and only for one beacon.
Signed-off-by: Felix Fietkau <[email protected]>
If the radio was previously in running state, it can receive some
packets before it is able to process them.
This can lead to a crash if the channel is not initialized yet.
Discard all rx packets until start() is called
Signed-off-by: Felix Fietkau <[email protected]>
According to 802.11-2007 17.3.8.6 (slot time), the slot time should
be increased by 3 us * coverage class. Taking into account coverage
class in slot time configuration allows to increase by an order of
magnitude the throughput on a 4Km link in a noisy environment
Tested-by: Luca Bisti <[email protected]>
Tested-by: Gaetano Catalli <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
For encryption to work properly, the BSS index needs to be initialized
for the WCID entry used for the interface.
Signed-off-by: Felix Fietkau <[email protected]>
Add a usleep_range in mt76x2_mac_stop routine in order to add
a polling delay checking values of MT_MAC_STATUS and IBI_R12 registers
Signed-off-by: Lorenzo Bianconi <[email protected]>
