Set UP in skb->priority to allow DSCP Learning at upper layers
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Enable VTA flag in txwi to enable HQD in SPL which is needed by
the PST. Without this patch, PST cannot get the correct delay of
TxD and lead to a large latency.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Set MT_WF_RFCR_DROP_OTHER_UC by default and disable this flag in
mt7996_set_monitor only if monitor mode is enabled.
Without this patch, the MT_WF_RFCR_DROP_OTHER_UC would not be set so the
driver would receive lots of packets meant for other devices.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Ensure that a key for a link is only added and removed once.
When bringing up a link, only upload keys for that particular link, instead
of iterating over all of them.
Signed-off-by: Felix Fietkau <[email protected]>
While deleting sta keys can be omitted in order to fix race conditions,
vif keys must be deleted before being replaced in order to prevent
accidental reuse in firmware.
Signed-off-by: Felix Fietkau <[email protected]>
Include beacon key information in the STA_REC_UPDATE call.
Remove mt7996_mcu_get_pn - when installing a new key, we should
not reuse any existing PN value.
Signed-off-by: Allen Ye <[email protected]>
Signed-off-by: Michael-CY Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This allows faster recovery from firmware issues.
Based on patch by Chad Monroe and ported from mt7915.
Signed-off-by: Felix Fietkau <[email protected]>
Port latest version of similar changes from mt7915:
- use reconfig_complete to restart mac_work / queues
- reset full wtbl after firmware init
- clear wcid and vif mask to avoid leak
- fix sta poll list corruption
- clear rro list
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
There is only one wiphy, so extra calls must be removed.
For calls that need to remain per-wiphy, use mt7996_for_each_phy
Fixes: 69d54ce7491d ("wifi: mt76: mt7996: switch to single multi-radio wiphy")
Signed-off-by: Felix Fietkau <[email protected]>
Support writing MAC TXD for the AddBA Req. Without this commit, the
start sequence number in AddBA Req will be unexpected value for MT7996
and MT7992. This can result in certain stations (e.g., AX200) dropping
packets, leading to ping failures and degraded connectivity. Ensuring
the correct MAC TXD and TXP helps maintain reliable packet transmission
and prevents interoperability issues with affected stations.
Signed-off-by: Howard Hsu <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Set `tx_power_tlv->len` to `msg_len` instead of `sizeof(*tx_power_tlv)`
to ensure the correct message length is sent to firmware.
Cc: [email protected]
Fixes: c948b5da6bbe ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Signed-off-by: Ming Yen Hsieh <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
In vendor driver, size of group cal and dpd cal for mt7981 includes 6G
although the chip doesn't support it.
mt76 doesn't take this into account which results in reading from the
incorrect offset.
For devices with precal, this would lead to lower bitrate.
Fix this by aligning groupcal size with vendor driver and switch to
freq_list_v2 in mt7915_dpd_freq_idx in order to get the correct offset.
Below are iwinfo of the test device with two clients connected
(iPhone 16, Intel AX210).
Before :
Mode: Master Channel: 36 (5.180 GHz) HT Mode: HE80
Center Channel 1: 42 2: unknown
Tx-Power: 23 dBm Link Quality: 43/70
Signal: -67 dBm Noise: -92 dBm
Bit Rate: 612.4 MBit/s
Encryption: WPA3 SAE (CCMP)
Type: nl80211 HW Mode(s): 802.11ac/ax/n
Hardware: embedded [MediaTek MT7981]
After:
Mode: Master Channel: 36 (5.180 GHz) HT Mode: HE80
Center Channel 1: 42 2: unknown
Tx-Power: 23 dBm Link Quality: 43/70
Signal: -67 dBm Noise: -92 dBm
Bit Rate: 900.6 MBit/s
Encryption: WPA3 SAE (CCMP)
Type: nl80211 HW Mode(s): 802.11ac/ax/n
Hardware: embedded [MediaTek MT7981]
Tested-on: mt7981 20240823
Fixes: 19a954edec63 ("wifi: mt76: mt7915: add mt7986, mt7916 and mt7981 pre-calibration")
Signed-off-by: Zhi-Jun You <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Move the NULL check for 'sta' before dereferencing it to prevent a
possible crash.
Fixes: 44eb173bdd4f ("wifi: mt76: mt7925: add link handling in mt7925_txwi_free")
Signed-off-by: Ming Yen Hsieh <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Check for a NULL `vif` before accessing `ieee80211_vif_is_mld(vif)` to
avoid a potential kernel panic in scenarios where `vif` might not be
initialized.
Fixes: ebb1406813c6 ("wifi: mt76: mt7925: add link handling to txwi")
Signed-off-by: Ming Yen Hsieh <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Introduce rx_rro_ind_process and rx_rro_add_msdu_page callbacks and the
related logic in the MT7996 driver. This is a preliminary patch to
decouple RRO logic from WED support and reuse RRO when WED module is not
available.
Signed-off-by: Rex Lu <[email protected]>
Co-developed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
In order to properly set the number of rx packets for primary WED device
if hif device is available, move hif pointer initialization before
running mt7996_mmio_wed_init routine.
Fixes: 83eafc9251d6d ("wifi: mt76: mt7996: add wed tx support")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Introduce the second WDMA RX ring in WED driver for MT7988 SoC since the
Mediatek MT7992 WiFi chipset supports two separated WDMA rings.
Add missing MT7988 configurations to properly support WED for MT7992 in
MT76 driver.
Co-developed-by: Rex Lu <[email protected]>
Signed-off-by: Rex Lu <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
Embedding net_device into structures prohibits the usage of flexible
arrays in the net_device structure. For more details, see the discussion
at [1].
Un-embed the net_devices from struct mt76_dev by converting them
into pointers, and allocating them dynamically. Use the leverage
alloc_netdev_dummy() to allocate the net_device object at
mt76_dma_init().
The free of the device occurs at mt76_dma_cleanup().
Link: https://lore.kernel.org/all/[email protected]/ [1]
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: Breno Leitao <[email protected]>
Acked-by: Kalle Valo <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
Any station configured with an AID over 20 causes a firmware crash.
This situation occurred in our testing using an AP interface on 7922
hardware, with a modified hostapd, sourced from Mediatek's OpenWRT
feeds.
In stock hostapd, station AIDs begin counting at 1, and this
configuration is prevented with an upper limit on associated stations.
However, the modified hostapd began allocation at 65, which caused the
firmware to crash. This fix does not allow these AIDs to work, but will
prevent the firmware crash.
This crash was only seen on IFTYPE_AP interfaces, and the fix does not
appear to have an effect on IFTYPE_STATION behavior.
Fixes: 5c14a5f944b9 ("mt76: mt7921: introduce mt7921e support")
Signed-off-by: Rory Little <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Felix Fietkau