This is a preliminary patch to introduce WED support for mt7996
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mtk_wed_device pointer in mt76_queue structure in order to
configure WED chip.
Get rid of dev parameter in Q_READ and Q_WRITE macros.
Introduce wed parameter to the following routine signatures:
- mt76_init_queue
- mt76_init_tx_queue
This is a preliminary patch to introduce WED support for mt7996 since
mt7996 runs two separate WED chips.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce WED support for mt7996
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce WED support for mt7996
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt76_mmio_wed_offload_enable and mt76_mmio_wed_offload_disable routines
will be reused by mt7996 driver for wed support.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_mmio_wed_init_rx_buf and mt76_mmio_wed_release_rx_buf routines
in common code.
This is a preliminary patch to introduce WED support for mt7996
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Permit to load precal from NVMEM cell for mt7915. The NVMEM cell must be
named "precal" to be correctly loaded.
NVMEM cell must already account the correct offset and be placed after
the EEPROM as the function expect the data right from the start.
Tested-by: Shiji Yang <[email protected]>
Signed-off-by: Christian Marangi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Generilize mt76_get_of_eeprom_from_nvmem to use alternative cell name by
passing the cell name as an arg and expose it.
Rename it to mt76_get_of_data_from_nvmem to better reflect the now more
generic usage.
This is to permit driver to load additional cell, like precal cell.
Tested-by: Shiji Yang <[email protected]>
Signed-off-by: Christian Marangi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Since mt76_get_of_eeprom is not used by mt7915 anymore, unexport it and
make it static again.
Also drop offset arg as it's only supported for MTD and was always set
to 0, hardcode the MTD functio instead.
Signed-off-by: Christian Marangi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Limit support for precal loading for mt7915 only to MTD. Passing data
from DT doesn't support offset and NVMEM require a different cell name
and doesn't support offset hence only MTD way is actually supported.
Rename mt76_get_of_eeprom_from_mtd to mt76_get_of_data_from_mtd as it is
now used for a more generic purpose and export it.
Signed-off-by: Christian Marangi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix typo in mt76_get_of_eeprom_from_nvmem where eeprom was misspelled as
epprom.
Fixes: 5bef3a406c6e ("wifi: mt76: add support for providing eeprom in nvmem cells")
Signed-off-by: Christian Marangi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix the uninitialized variable warning in mt7996_mac_tx_free.
Fixes: 2461599f835e: "wifi: mt76: mt7996: get tx_retries and tx_failed from txfree"
Signed-off-by: Yi-Chia Hsieh <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The mtcl table, configured by platform vendor, provides regulatory
information for 5.9/6 GHz channels. mt792x should work on
corresponding channels supported by mtcl. This patch would parse
the settings in mtcl table and apply the result into chip side.
Signed-off-by: Rong Yan <[email protected]>
Co-developed-by: Deren Wu <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add ability to explicitly forbid LED registration using DT led\status = "disabled".
Tested-by: Alexey D. Filimonov <[email protected]>
Signed-off-by: Alexey D. Filimonov <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The 5.9/6GHz channel license of a certain platform device has been
regulated in various countries. That may be difference with standard
Liunx regulatory domain settings. In this case, when .reg_notifier()
called for regulatory change, mt792x chipset should update the channel
usage based on clc or dts configurations.
Channel would be disabled by following cases.
* clc report the particular UNII-x is disabled.
* dts enabled and the channel is not configured.
Signed-off-by: Ming Yen Hsieh <[email protected]>
Co-developed-by: Deren Wu <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The clc event can report the radio configuration for the corresponding
country and the driver would take it as regulatory information of a
certain platform device.
This patch would change the clc commnad from no-waiting to waiting for
event. For backward compatible, we also add a new nic capability tag
to indicate the firmware did support this new clc event from now on.
Signed-off-by: Ming Yen Hsieh <[email protected]>
Co-developed-by: Deren Wu <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
There are several power type should be supported in 6GHz band. mt7921
apply 6GHz power type from AP settings and clc will setup the
corresponding regulatory power.
Signed-off-by: Ming Yen Hsieh <[email protected]>
Co-developed-by: Deren Wu <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt76_connac_mcu_get_nic_capability() is used by mt7921 only. It
would be better to put the code in chip folder. And we can provide
more chip capability information in mt792x_phy without making
mt76_phy much bigger.
The three functions would be moved to mt7921 folder and renamed.
mt76_connac_mcu_parse_tx_resource()
mt76_connac_mcu_parse_phy_cap()
mt76_connac_mcu_get_nic_capability()
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt76_dma_rx_cleanup would be frequenetly called up to reset the dma rings
to be freshed as new ones when switching back from the deep sleep mode to
the active mode on mt7921 and mt7922.
Shrink the scope of spin_lock_bh in mt76_dma_rx_cleanup being held up
to allow the kernel scheduler to be able to switch other tasks in time
by reducing the latency.
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove periodic MPDU TXS request. Get TID and FrameType from SKB
instead of TXWI, which is empty for Data Frame after MPDU TXS request
is removed, hence prohibiting the establishment of TX BA session.
Signed-off-by: Benjamin Lin <[email protected]>
Signed-off-by: Yi-Chia Hsieh <[email protected]>
Signed-off-by: Money Wang <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Evelyn Tsai <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Enable PPDU TxS by default. This makes the driver able to get Tx rate
information from TxS. The driver will also refresh BA session timer
on receive of PPDU TxS when WED is on.
Signed-off-by: Yi-Chia Hsieh <[email protected]>
Signed-off-by: Money Wang <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Evelyn Tsai <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Per peer Tx/Rx statistic can only be obtained by querying WM when WED is
on. This patch switches to periodic event reporting in the case of WED
being enabled.
Signed-off-by: Yi-Chia Hsieh <[email protected]>
Signed-off-by: Money Wang <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Evelyn Tsai <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move the following shared usb routines in mt792x module:
- mt792xu_stop
- mt792x_stop
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Since mt7921_skb_add_usb_sdio_hdr is shared between mt7925 and mt7921
drivers, move it in mt792x module.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
On MT76x0, LNA gain should be applied for both external and internal LNA.
On MT76x2, LNA gain should be treated as 0 for external LNA.
Move the LNA type based logic to mt76x2 in order to fix mt76x0.
Fixes: 2daa67588f34 ("mt76x0: unify lna_gain parsing")
Reported-by: Shiji Yang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add mt7925, a new mac80211 driver for the MediaTek Wi-Fi 7 (802.11be) device
Filogic 360, which can support Station, AP, P2P, and monitor modes.
Filogic 360 supports max 4096-QAM/160MHz radio operation at 6 GHz, 5 GHz,
or 2.4 GHz with 2x2 antennas. This chip supports PCIe and USB bus type.
mt7925 supports Wi-Fi 6E and EHT rate with single link only at this moment,
whereas Wi-Fi 7 and its specific features are working in progress. They will be
introduced in further patches.
The driver is build tested by Intel's kernel test robot with both GCC and Clang
with several architecture. Sparse reports no warnings.
There are multiple authors, they are listed in alphabetical order below.
Co-developed-by: Hao Zhang <[email protected]>
Signed-off-by: Hao Zhang <[email protected]>
Co-developed-by: Leon Yen <[email protected]>
Signed-off-by: Leon Yen <[email protected]>
Co-developed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Co-developed-by: Mingyen Hsieh <[email protected]>
Signed-off-by: Mingyen Hsieh <[email protected]>
Co-developed-by: Nelson Yu <[email protected]>
Signed-off-by: Nelson Yu <[email protected]>
Co-developed-by: Quan Zhou <[email protected]>
Signed-off-by: Quan Zhou <[email protected]>
Co-developed-by: Rong Yan <[email protected]>
Signed-off-by: Rong Yan <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The variable band should be determined by the ieee80211_chanctx_conf when
the driver is a kind of chanctx one e.g mt7921 and mt7922 driver so we
added the extension to mt76_connac2_mac_tx_rate_val and
mt76_connac_get_he_phy_cap for the firmware can select the proper rate.
Fixes: 41ac53c899bd ("wifi: mt76: mt7921: introduce chanctx support")
Signed-off-by: Sean Wang <[email protected]>
Tested-by: David Ruth <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The variable band should be determined by the ieee80211_chanctx_conf when
the driver is a kind of chanctx one e.g mt7921 and mt7922 driver so we
added the extension to mt76_connac2_mac_tx_rate_val by distinguishing if
it can support chanctx to fix the incorrect rate pickup.
Fixes: 41ac53c899bd ("wifi: mt76: mt7921: introduce chanctx support")
Signed-off-by: Sean Wang <[email protected]>
Reviewed-by: David Ruth <[email protected]>
Tested-by: David Ruth <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move struct ieee80211_chanctx_conf up to struct mt76_vif to allow the
connac2 library can access the struct ieee80211_chanctx_conf * member in
struct mt76_vif.
Signed-off-by: Sean Wang <[email protected]>
Reviewed-by: David Ruth <[email protected]>
Tested-by: David Ruth <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
debugfs_create_dir() returns ERR_PTR and never return NULL.
As Russell suggested, this patch removes the error checking for
debugfs_create_dir(). This is because the DebugFS kernel API is developed
in a way that the caller can safely ignore the errors that occur during
the creation of DebugFS nodes. The debugfs APIs have a IS_ERR() judge in
start_creating() which can handle it gracefully. So these checks are
unnecessary.
Fixes: 17f1de56df05 ("mt76: add common code shared between multiple chipsets")
Signed-off-by: Jinjie Ruan <[email protected]>
Suggested-by: Russell King (Oracle) <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Without this patch, when ap sets the tx stream number to 2,
ap won't send any beamforming packet.
Fixes: f89f297aef28 ("mt76: mt7915: fix txbf starec TLV issues")
Signed-off-by: MeiChia Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Set mpdu density to 2 usec for non-mt7915 Wi-Fi 6 generation chipsets
to align to the hardware capability which improves the throughput.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Do not report cca and csa finish to upper layer on station type vif to
prevent warnings caused by setting beacon.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use the correct ieee80211_conf of each band for IEEE80211_CONF_MONITOR
comparison.
Fixes: 24e69f6bc3ca ("mt76: fix monitor rx FCS error in DFS channel")
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When the set_chan_info command is set with CH_SWITCH_NORMAL reason,
even if the action is UNI_CHANNEL_RX_PATH, it'll still generate some
unexpected tones, which might confuse DFS CAC tests that there are some
tone leakages. To get rid of these kinds of false alarms, always bypass
DPD calibration when IEEE80211_CONF_IDLE is set.
Reviewed-by: Evelyn Tsai <[email protected]>
Signed-off-by: StanleyYP Wang <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add CAP3_RX_CTRL_FRAME_TO_MULTIBSS check when setting sta_muru_tlv,
which is used to get stations's capability of receiving control frames
when running OFDMA with MBSSIDs.
Signed-off-by: Allen Ye <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When compiling with clang 16.0.6 and CONFIG_FORTIFY_SOURCE=y, I've
noticed the following (somewhat confusing due to absence of an actual
source code location):
In file included from drivers/net/wireless/mediatek/mt76/mt792x_core.c:4:
In file included from ./include/linux/module.h:13:
In file included from ./include/linux/stat.h:19:
In file included from ./include/linux/time.h:60:
In file included from ./include/linux/time32.h:13:
In file included from ./include/linux/timex.h:67:
In file included from ./arch/x86/include/asm/timex.h:5:
In file included from ./arch/x86/include/asm/processor.h:23:
In file included from ./arch/x86/include/asm/msr.h:11:
In file included from ./arch/x86/include/asm/cpumask.h:5:
In file included from ./include/linux/cpumask.h:12:
In file included from ./include/linux/bitmap.h:11:
In file included from ./include/linux/string.h:254:
./include/linux/fortify-string.h:592:4: warning: call to '__read_overflow2_field'
declared with 'warning' attribute: detected read beyond size of field (2nd
parameter); maybe use struct_group()? [-Wattribute-warning]
__read_overflow2_field(q_size_field, size);
In file included from drivers/net/wireless/mediatek/mt76/mt7915/main.c:4:
In file included from ./include/linux/etherdevice.h:20:
In file included from ./include/linux/if_ether.h:19:
In file included from ./include/linux/skbuff.h:15:
In file included from ./include/linux/time.h:60:
In file included from ./include/linux/time32.h:13:
In file included from ./include/linux/timex.h:67:
In file included from ./arch/x86/include/asm/timex.h:5:
In file included from ./arch/x86/include/asm/processor.h:23:
In file included from ./arch/x86/include/asm/msr.h:11:
In file included from ./arch/x86/include/asm/cpumask.h:5:
In file included from ./include/linux/cpumask.h:12:
In file included from ./include/linux/bitmap.h:11:
In file included from ./include/linux/string.h:254:
./include/linux/fortify-string.h:592:4: warning: call to '__read_overflow2_field'
declared with 'warning' attribute: detected read beyond size of field (2nd
parameter); maybe use struct_group()? [-Wattribute-warning]
__read_overflow2_field(q_size_field, size);
In file included from drivers/net/wireless/mediatek/mt76/mt7996/main.c:6:
In file included from drivers/net/wireless/mediatek/mt76/mt7996/mt7996.h:9:
In file included from ./include/linux/interrupt.h:8:
In file included from ./include/linux/cpumask.h:12:
In file included from ./include/linux/bitmap.h:11:
In file included from ./include/linux/string.h:254:
./include/linux/fortify-string.h:592:4: warning: call to '__read_overflow2_field'
declared with 'warning' attribute: detected read beyond size of field (2nd
parameter); maybe use struct_group()? [-Wattribute-warning]
__read_overflow2_field(q_size_field, size);
The compiler actually complains on 'mt7915_get_et_strings()',
'mt792x_get_et_strings()' and 'mt7996_get_et_strings()' due to the same
reason: fortification logic inteprets call to 'memcpy()' as an attempt
to copy the whole array from its first member and so issues an overread
warning. These warnings may be silenced by passing an address of the whole
array and not the first member to 'memcpy()'.
Signed-off-by: Dmitry Antipov <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In the Xiaomi Redmibook 15 Pro (2023) laptop I have got, a wifi chip is
used, which according to its PCI Vendor ID is from "ITTIM Technology".
This chip works flawlessly with the mt7921e module. The driver doesn't
bind to this PCI device, because the Vendor ID from "ITTIM Technology" is
not recognized.
This patch adds the PCI Vendor ID from "ITTIM Technology" to the list of
PCI Vendor IDs and lets the mt7921e driver bind to the mentioned wifi
chip.
Signed-off-by: Ingo Rohloff <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Extend settings of LED registers to support per-band configuration.
Signed-off-by: Jen-Hao Cheng <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add support to configure parameters at runtime, such as mcs, gi, and
he_ltf. Note that EHT mode does not support this feature yet.
Co-developed-by: MeiChia Chiu <[email protected]>
Signed-off-by: MeiChia Chiu <[email protected]>
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Only send commands that disable vif when removing interface, this
reduces some unnecessary bss_info and sta_rec commands, especially for
station interface.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
