This reverts commit fea36e0207.
When reaching that point, a frame has always been enqueued and we need
to kick the queue
Signed-off-by: Felix Fietkau <[email protected]>
Leave more time to abort transmissions (which could happen at low CCK rates)
Only warn if the last filter command is stuck
Signed-off-by: Felix Fietkau <[email protected]>
If the driver has configured the hardware to drop packets for a sta that was
in powersave mode, then clearing the flag too early opens up a small race
window during which packets could be dropped on wakeup
Signed-off-by: Felix Fietkau <[email protected]>
Typically all AP interfaces on a PHY will share the same WMM settings, while
sta/mesh interfaces will usually inherit the settings from a remote device.
In order minimize the likelihood of conflicting WMM settings, make all AP
interfaces share one slot, and all non-AP interfaces another one.
Signed-off-by: Felix Fietkau <[email protected]>
Typically all AP interfaces on a PHY will share the same WMM settings, while
sta/mesh interfaces will usually inherit the settings from a remote device.
In order minimize the likelihood of conflicting WMM settings, make all AP
interfaces share one slot, and all non-AP interfaces another one.
This also fixes running multiple AP interfaces on MT7613, which only has 3
WMM slots.
Signed-off-by: Felix Fietkau <[email protected]>
With 4-address mode VLAN frames, an internal header translation step fails,
leaving behind an extra 2-byte length field that must be reomved by the driver.
Add a check for this condition to fix receiving such packets
Signed-off-by: Felix Fietkau <[email protected]>
With 4-address mode VLAN frames, an internal header translation step fails,
leaving behind an extra 2-byte length field that must be reomved by the driver.
Add a check for this condition to fix receiving such packets
Signed-off-by: Felix Fietkau <[email protected]>
napi_schedule() can call __raise_softirq_irqoff(), which can perform softirq
handling, so it must not be called in a pure process context with BH enabled.
Signed-off-by: Felix Fietkau <[email protected]>
WMM index range needs to be split between both PHYs if a second PHY exists.
The condition for that was accidentally written as checking if the vif PHY
is the secondary one
Signed-off-by: Felix Fietkau <[email protected]>
When clearing all existing pending tx slots, mt76_tx_complete_skb needs to
be used to free the skbs, to ensure that they are cleared from the status
list as well.
Cc: [email protected]
Signed-off-by: Felix Fietkau <[email protected]>
- Remove no-op code for queue lock/unlock, which is no longer needed
- Set a missing DMA flag
- Wait for full completion of error recovery before restarting tx
- Schedule IRQ tasklet to ensure that IRQ mask gets written
Signed-off-by: Felix Fietkau <[email protected]>
There are firmware or hardware issues, which are currently causing tx hangs
when attempting to use these interfaces
Signed-off-by: Felix Fietkau <[email protected]>
The device tree partition offset needs to be added to the function argument,
instead of overwriting it.
Fixes an issue where wrong EEPROM data was sent to the firmware as
pre-calibration data on MT7915.
Fixes: 495184ac91bb ("mt76: mt7915: add support for applying pre-calibration data")
Signed-off-by: Felix Fietkau <[email protected]>
Mitigate A-MSDU injection attacks (CVE-2020-24588) by detecting if the
destination address of a subframe equals an RFC1042 (i.e., LLC/SNAP)
header, and if so dropping the complete A-MSDU frame. This mitigates
known attacks, although new (unknown) aggregation-based attacks may
remain possible.
This defense works because in A-MSDU aggregation injection attacks, a
normal encrypted Wi-Fi frame is turned into an A-MSDU frame. This means
the first 6 bytes of the first A-MSDU subframe correspond to an RFC1042
header. In other words, the destination MAC address of the first A-MSDU
subframe contains the start of an RFC1042 header during an aggregation
attack. We can detect this and thereby prevent this specific attack.
For details, see Section 7.2 of "Fragment and Forge: Breaking Wi-Fi
Through Frame Aggregation and Fragmentation".
Signed-off-by: Felix Fietkau <[email protected]>
Instead of attaching the last reported rate to tx packets, use
ieee80211_tx_status_ext to immediately pass the rate to mac80211 after
receiving it from the firmware.
Preparation for implementing full tx status reporting
Signed-off-by: Felix Fietkau <[email protected]>
Use ieee80211_tx_status_ext instead of ieee80211_free_skb and
ieee80211_tx_status. This makes it compatible with 802.3 encap offload
and improves performance by removing a redundant sta lookup
Signed-off-by: Felix Fietkau <[email protected]>
The hardware can only handle 64 subframes in rx direction and 128 for tx.
Improves throughput with APs that can handle more than that
Signed-off-by: Felix Fietkau <[email protected]>
For MT7663, the availability of the patch files is used to detect, which
corresponding firmware is going to be used (AP firmware or STA offload
firmware). If the ROM patch was already applied, it could attempt to
load the wrong firmware (without considering the alternative).
Signed-off-by: Felix Fietkau <[email protected]>
MT7663 uses different bits for communicating reset commands/status between MCU
and host. Also add an extra initial reset command.
Signed-off-by: Felix Fietkau <[email protected]>
After DMA reset, tx status information for queued frames will never arrive.
Flush the queue to free skbs immediately instead of waiting for a timeout
Signed-off-by: Felix Fietkau <[email protected]>
Ensures that header translation is disabled for interfaces that do not support
it.
Fixes: bb1262e7199b ("mt76: mt7615: add support for rx decapsulation offload")
Signed-off-by: Felix Fietkau <[email protected]>
When receiving an A-MSDU containing only a single subframe, status->last_amsdu
is set, but no previous head is present in the rx A-MSDU queue.
In this case, the A-MSDU subframe will be held until the next one is received,
potentially causing significant extra latency.
Rework the code to make it easier to read and less convoluted, and release the
newly created head if status->last_amsdu is set.
Signed-off-by: Felix Fietkau <[email protected]>
After chip reset, the DMA scheduler needs to be initialized as well.
Since the code is PCI/SoC specific, move it to pci_mac.c, so that it
can depend on a function in dma.c
Signed-off-by: Felix Fietkau <[email protected]>
When disassociating and clearing the BSSID of a repeater entry used by a client
mode interface, the corresponding MAC address entry can get lost too, causing
the client interface to not be able to associate anymore.
Fix this by also refreshing the MAC address when setting the BSSID
Signed-off-by: Felix Fietkau <[email protected]>
With buf uninitialized in mt76_dma_tx_queue_skb_raw, its field skip_unmap
could potentially inherit a non-zero value from stack garbage.
If this happens, it will cause DMA mappings for MCU command frames to not be
unmapped after completion
Fixes: 27d5c528a7ca ("mt76: fix double DMA unmap of the first buffer on 7615/7915")
Cc: [email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Deleting a key with the previous key index deletes the current key
Rework the code to better keep track of multiple keys and check for the
key index before deleting the current key
Signed-off-by: Felix Fietkau <[email protected]>
When running out of room in the tx queue after calling drv->tx_prepare_skb,
the buffer list will already have been modified on MT7615 and newer drivers.
This can leak a DMA mapping and will show up as swiotlb allocation failures
on x86.
Fix this by moving the queue length check further up. This is less accurate,
since it can overestimate the needed room in the queue on MT7615 and newer,
but the difference is small enough to not matter in practice.
Signed-off-by: Felix Fietkau <[email protected]>
For AP and Client mode, the hardware can pass received packets as 802.3 frames
that can be passed to the network stack as-is.
Signed-off-by: Felix Fietkau <[email protected]>
The first pointer in the txp needs to be unmapped as well, otherwise it will
leak DMA mapping entries
Fixes: 27d5c528a7ca ("mt76: fix double DMA unmap of the first buffer on 7615/7915")
Signed-off-by: Felix Fietkau <[email protected]>
The first pointer in the txp needs to be unmapped as well, otherwise it will
leak DMA mapping entries
Fixes: 27d5c528a7ca ("mt76: fix double DMA unmap of the first buffer on 7615/7915")
Signed-off-by: Felix Fietkau <[email protected]>
There were multiple issues in the current key set/remove code:
- deleting a key with the previous key index deletes the current key
- BIP key would only be uploaded correctly initially and corrupted on rekey
Rework the code to better keep track of multiple keys and check for the
key index before deleting the current key
Signed-off-by: Felix Fietkau <[email protected]>
With a maximum length of 7991, the radio sometimes locks up under load when
transmitting A-MSDU frames to lots of stations. Using the lower limit makes
it work reliably again
Signed-off-by: Felix Fietkau <[email protected]>
Instead of holding it for the duration of an entire station schedule run,
which can block out competing tasks for a significant amount of time,
only hold it for scheduling one batch of packets for one station.
Improves responsiveness under load
Signed-off-by: Felix Fietkau <[email protected]>
For performance reasons, mt7915 supports using 2 PCIE gen1 links on
platforms that don't support gen2.
Add support for using this to move traffic for a second DBDC band onto
a dedicated link
Signed-off-by: Felix Fietkau <[email protected]>
Since vif indexes are per-phy, we need to factor in the phy index to avoid
collisions on the WTBL index
Signed-off-by: Felix Fietkau <[email protected]>
Only clear dev->phy2 after the phy is gone, the driver may still need to access
it until shutdown is complete
Signed-off-by: Felix Fietkau <[email protected]>
When the EEPROM band fields contain default values, assign 2.4 GHz to the
first band and 5 GHz to the second.
Signed-off-by: Felix Fietkau <[email protected]>
It causes high CPU load on the WA core, which can lead to extra latency when
using many stations. Dropping packets for long queues is managed by mac80211
fq_codel instead
Signed-off-by: Felix Fietkau <[email protected]>
Add support for passing flags for selecting the MCU target and query type
instead of trying to detect it based on the command id
Signed-off-by: Felix Fietkau <[email protected]>
Felix Fietkau