Introduce mcu_reset function pointer in mt76_mcu_ops structure in order
to run hw related reset function for the mcu running on the chipset.
This is a preliminary patch to introduce chip reset for mt7921 devices.
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Reduce mcu timeout for the following uni mcu commands:
- MCU_UNI_CMD_SUSPEND
- MCU_UNI_CMD_OFFLOAD
- MCU_UNI_CMD_HIF_CTRL
This is a preliminary patch to introduce chip reset support
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
ieee80211_register_hw() is called with rtnl_lock held, and this could be
caused lockdep from a work item that's on a workqueue that is flushed
with the rtnl held.
Move mt7915_register_ext_phy() outside the init_work().
Signed-off-by: Evelyn Tsai <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use the additional memory barrier to ensure the skb list up-to-date
between the skb producer and consumer to avoid the invalid skb content
written into sdio controller and then cause device hang due to mcu assert
caught by WR_TIMEOUT_INT.
Fixes: 1522ff731f84 ("mt76: mt7663s: introduce sdio tx aggregation")
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Each packet should be padded with the additional zero to become 4-bytes
alignment in sdio tx aggregation.
Fixes: 1522ff731f84 ("mt76: mt7663s: introduce sdio tx aggregation")
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
HW beacon filter command is being applied until we're in associated state
because the command would rely on the associated access point's beacon
interval and DTIM information.
Fixes: 7124198ab1a4 ("mt76: mt7615: enable beacon filtering by default for offload fw")
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Properly check returned values from mcu utility routines in
mt7615_ops.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Properly check returned values from mcu utility routines in
mt7915_ops.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Avoid directly updating sinfo->rxrate from firmware since rate_info might
be overwritten by wrong results even mt7915_mcu_get_rx_rate() fails check.
Add more error handlings accordingly.
Fixes: 11553d88d0b9 ("mt76: mt7915: query station rx rate from firmware")
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Properly check returned values from mcu utility routines in
mt7921_start.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
We should change the base for the dynamic remap into another one, because
the current base (0xe0000) have been the one used to operate the device
ownership.
Fixes: 163f4d22c118 ("mt76: mt7921: add MAC support")
Co-developed-by: YN Chen <[email protected]>
Signed-off-by: YN Chen <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Should use 0x10000 as the base to operate PCIe interrupt according
to the vendor reference driver.
Fixes: ffa1bf97425b ("mt76: mt7921: introduce PM support")
Co-developed-by: YN Chen <[email protected]>
Signed-off-by: YN Chen <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Tested-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Since the rate selection is currently managed by the fw, get rid of
empty mt7921_sta_rc_update routine
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Since mt76_txq_send_burst routine can report a negative error code,
check the returned value before incrementing the number of transmitted
frames in mt76_txq_schedule_list routine.
Return -EBUSY directly if the device is in reset or in power management.
Fixes: 90fdc1717b186 ("mt76: use mac80211 txq scheduling")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In order to properly report MIB counters to mac80211, resets stats in
mt7915_get_stats routine() and hold mt76 mutex accessing MIB counters.
Sum up MIB counters in mt7915_mac_update_mib_stats routine.
Fixes: c6b002bcdf ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In order to properly report MIB counters to mac80211, resets stats in
mt7615_get_stats routine and hold mt76 mutex accessing MIB counters.
Sum up MIB counters in mt7615_mac_update_mib_stats routine.
Fixes: c388d8584bc83 ("mt76: mt7615: add a get_stats() callback")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Only mt7615 uses v1 version. Also, some of released firmware doesn't
have hdr->fw_ver.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The index of TSF counters should follow HWBSSID.
Fixes: cd79526761 ("mt76: mt7615: support 16 interfaces")
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Similar to mt7921, fix 802.11 aggr len debugfs reporting for mt7915 driver.
Fixes: e57b7901469fc ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Similar to the issue fixed in mt7921_coredump_work, fix a possible memory
leak in mt7615_coredump_work routine.
Fixes: d2bf7959d9c0f ("mt76: mt7663: introduce coredump support")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
For AP and Client mode, the hardware can pass received packets
as 802.3 frames that can be passed to the network stack as-is.
Tested-by: Frank Wunderlich <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Set skb->ip_summed to CHECKSUM_UNNECESSARY if the hardware has validated
the IP and TCP/UDP checksum
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Enable hw rx-amsdu de-aggregation support.
This is a preliminary patch to enable rx checksum offload.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Since the related rx bitrate fields have been moved to group3 in Rxv,
fix rx bitrate statistics in mt7921_mac_fill_rx routine.
Fixes: 163f4d22c118d ("mt76: mt7921: add MAC support")
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Current firmware only supports new api for enabling hardware beacon filter.
Fixes: 1d8efc741df80 ("mt76: mt7921: introduce Runtime PM support")
Beacon filter cmd have to rely on the associatied access point's beacon
interval and DTIM information.
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix possible memory leak in mt7921_coredump_work.
Fixes: 1c099ab44727c ("mt76: mt7921: add MCU support")
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Any pcie access should happen in pci D0 state and we should give ownership
back to the device at the end of the suspend procedure.
Fixes: 1d8efc741df80 ("mt76: mt7921: introduce Runtime PM support")
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
clang points out a possible corner case in the mt7915_tm_set_tx_cont()
function if called with invalid arguments:
drivers/net/wireless/mediatek/mt76/mt7915/testmode.c:593:2: warning: variable 'mode' is used uninitialized whenever switch default is taken [-Wsometimes-uninitialized]
default:
^~~~~~~
drivers/net/wireless/mediatek/mt76/mt7915/testmode.c:597:13: note: uninitialized use occurs here
rateval = mode << 6 | rate_idx;
^~~~
drivers/net/wireless/mediatek/mt76/mt7915/testmode.c:506:37: note: initialize the variable 'mode' to silence this warning
u8 rate_idx = td->tx_rate_idx, mode;
^
Change it to return an error instead of continuing with invalid data
here.
Fixes: 3f0caa3cbf94 ("mt76: mt7915: add support for continuous tx in testmode")
Signed-off-by: Arnd Bergmann <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
When running out of room in the tx queue after calling drv->tx_prepare_skb,
the buffer list will already have been modified on MT7615 and newer drivers.
This can leak a DMA mapping and will show up as swiotlb allocation failures
on x86.
Fix this by moving the queue length check further up. This is less accurate,
since it can overestimate the needed room in the queue on MT7615 and newer,
but the difference is small enough to not matter in practice.
Signed-off-by: Felix Fietkau <[email protected]>
For AP and Client mode, the hardware can pass received packets as 802.3 frames
that can be passed to the network stack as-is.
Signed-off-by: Felix Fietkau <[email protected]>
Enable hw rx-amsdu de-aggregation support available in 7915 devices.
This is a preliminary patch to enable rx checksum offload
Signed-off-by: Lorenzo Bianconi <[email protected]>
