On MT76x0, LNA gain should be applied for both external and internal LNA.
On MT76x2, LNA gain should be treated as 0 for external LNA.
Move the LNA type based logic to mt76x2 in order to fix mt76x0.
Fixes: 2daa67588f34 ("mt76x0: unify lna_gain parsing")
Reported-by: Shiji Yang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add mt7925, a new mac80211 driver for the MediaTek Wi-Fi 7 (802.11be) device
Filogic 360, which can support Station, AP, P2P, and monitor modes.
Filogic 360 supports max 4096-QAM/160MHz radio operation at 6 GHz, 5 GHz,
or 2.4 GHz with 2x2 antennas. This chip supports PCIe and USB bus type.
mt7925 supports Wi-Fi 6E and EHT rate with single link only at this moment,
whereas Wi-Fi 7 and its specific features are working in progress. They will be
introduced in further patches.
The driver is build tested by Intel's kernel test robot with both GCC and Clang
with several architecture. Sparse reports no warnings.
There are multiple authors, they are listed in alphabetical order below.
Co-developed-by: Hao Zhang <[email protected]>
Signed-off-by: Hao Zhang <[email protected]>
Co-developed-by: Leon Yen <[email protected]>
Signed-off-by: Leon Yen <[email protected]>
Co-developed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Co-developed-by: Mingyen Hsieh <[email protected]>
Signed-off-by: Mingyen Hsieh <[email protected]>
Co-developed-by: Nelson Yu <[email protected]>
Signed-off-by: Nelson Yu <[email protected]>
Co-developed-by: Quan Zhou <[email protected]>
Signed-off-by: Quan Zhou <[email protected]>
Co-developed-by: Rong Yan <[email protected]>
Signed-off-by: Rong Yan <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The variable band should be determined by the ieee80211_chanctx_conf when
the driver is a kind of chanctx one e.g mt7921 and mt7922 driver so we
added the extension to mt76_connac2_mac_tx_rate_val and
mt76_connac_get_he_phy_cap for the firmware can select the proper rate.
Fixes: 41ac53c899bd ("wifi: mt76: mt7921: introduce chanctx support")
Signed-off-by: Sean Wang <[email protected]>
Tested-by: David Ruth <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The variable band should be determined by the ieee80211_chanctx_conf when
the driver is a kind of chanctx one e.g mt7921 and mt7922 driver so we
added the extension to mt76_connac2_mac_tx_rate_val by distinguishing if
it can support chanctx to fix the incorrect rate pickup.
Fixes: 41ac53c899bd ("wifi: mt76: mt7921: introduce chanctx support")
Signed-off-by: Sean Wang <[email protected]>
Reviewed-by: David Ruth <[email protected]>
Tested-by: David Ruth <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move struct ieee80211_chanctx_conf up to struct mt76_vif to allow the
connac2 library can access the struct ieee80211_chanctx_conf * member in
struct mt76_vif.
Signed-off-by: Sean Wang <[email protected]>
Reviewed-by: David Ruth <[email protected]>
Tested-by: David Ruth <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
debugfs_create_dir() returns ERR_PTR and never return NULL.
As Russell suggested, this patch removes the error checking for
debugfs_create_dir(). This is because the DebugFS kernel API is developed
in a way that the caller can safely ignore the errors that occur during
the creation of DebugFS nodes. The debugfs APIs have a IS_ERR() judge in
start_creating() which can handle it gracefully. So these checks are
unnecessary.
Fixes: 17f1de56df05 ("mt76: add common code shared between multiple chipsets")
Signed-off-by: Jinjie Ruan <[email protected]>
Suggested-by: Russell King (Oracle) <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Without this patch, when ap sets the tx stream number to 2,
ap won't send any beamforming packet.
Fixes: f89f297aef28 ("mt76: mt7915: fix txbf starec TLV issues")
Signed-off-by: MeiChia Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Set mpdu density to 2 usec for non-mt7915 Wi-Fi 6 generation chipsets
to align to the hardware capability which improves the throughput.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Do not report cca and csa finish to upper layer on station type vif to
prevent warnings caused by setting beacon.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use the correct ieee80211_conf of each band for IEEE80211_CONF_MONITOR
comparison.
Fixes: 24e69f6bc3ca ("mt76: fix monitor rx FCS error in DFS channel")
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When the set_chan_info command is set with CH_SWITCH_NORMAL reason,
even if the action is UNI_CHANNEL_RX_PATH, it'll still generate some
unexpected tones, which might confuse DFS CAC tests that there are some
tone leakages. To get rid of these kinds of false alarms, always bypass
DPD calibration when IEEE80211_CONF_IDLE is set.
Reviewed-by: Evelyn Tsai <[email protected]>
Signed-off-by: StanleyYP Wang <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add CAP3_RX_CTRL_FRAME_TO_MULTIBSS check when setting sta_muru_tlv,
which is used to get stations's capability of receiving control frames
when running OFDMA with MBSSIDs.
Signed-off-by: Allen Ye <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When compiling with clang 16.0.6 and CONFIG_FORTIFY_SOURCE=y, I've
noticed the following (somewhat confusing due to absence of an actual
source code location):
In file included from drivers/net/wireless/mediatek/mt76/mt792x_core.c:4:
In file included from ./include/linux/module.h:13:
In file included from ./include/linux/stat.h:19:
In file included from ./include/linux/time.h:60:
In file included from ./include/linux/time32.h:13:
In file included from ./include/linux/timex.h:67:
In file included from ./arch/x86/include/asm/timex.h:5:
In file included from ./arch/x86/include/asm/processor.h:23:
In file included from ./arch/x86/include/asm/msr.h:11:
In file included from ./arch/x86/include/asm/cpumask.h:5:
In file included from ./include/linux/cpumask.h:12:
In file included from ./include/linux/bitmap.h:11:
In file included from ./include/linux/string.h:254:
./include/linux/fortify-string.h:592:4: warning: call to '__read_overflow2_field'
declared with 'warning' attribute: detected read beyond size of field (2nd
parameter); maybe use struct_group()? [-Wattribute-warning]
__read_overflow2_field(q_size_field, size);
In file included from drivers/net/wireless/mediatek/mt76/mt7915/main.c:4:
In file included from ./include/linux/etherdevice.h:20:
In file included from ./include/linux/if_ether.h:19:
In file included from ./include/linux/skbuff.h:15:
In file included from ./include/linux/time.h:60:
In file included from ./include/linux/time32.h:13:
In file included from ./include/linux/timex.h:67:
In file included from ./arch/x86/include/asm/timex.h:5:
In file included from ./arch/x86/include/asm/processor.h:23:
In file included from ./arch/x86/include/asm/msr.h:11:
In file included from ./arch/x86/include/asm/cpumask.h:5:
In file included from ./include/linux/cpumask.h:12:
In file included from ./include/linux/bitmap.h:11:
In file included from ./include/linux/string.h:254:
./include/linux/fortify-string.h:592:4: warning: call to '__read_overflow2_field'
declared with 'warning' attribute: detected read beyond size of field (2nd
parameter); maybe use struct_group()? [-Wattribute-warning]
__read_overflow2_field(q_size_field, size);
In file included from drivers/net/wireless/mediatek/mt76/mt7996/main.c:6:
In file included from drivers/net/wireless/mediatek/mt76/mt7996/mt7996.h:9:
In file included from ./include/linux/interrupt.h:8:
In file included from ./include/linux/cpumask.h:12:
In file included from ./include/linux/bitmap.h:11:
In file included from ./include/linux/string.h:254:
./include/linux/fortify-string.h:592:4: warning: call to '__read_overflow2_field'
declared with 'warning' attribute: detected read beyond size of field (2nd
parameter); maybe use struct_group()? [-Wattribute-warning]
__read_overflow2_field(q_size_field, size);
The compiler actually complains on 'mt7915_get_et_strings()',
'mt792x_get_et_strings()' and 'mt7996_get_et_strings()' due to the same
reason: fortification logic inteprets call to 'memcpy()' as an attempt
to copy the whole array from its first member and so issues an overread
warning. These warnings may be silenced by passing an address of the whole
array and not the first member to 'memcpy()'.
Signed-off-by: Dmitry Antipov <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In the Xiaomi Redmibook 15 Pro (2023) laptop I have got, a wifi chip is
used, which according to its PCI Vendor ID is from "ITTIM Technology".
This chip works flawlessly with the mt7921e module. The driver doesn't
bind to this PCI device, because the Vendor ID from "ITTIM Technology" is
not recognized.
This patch adds the PCI Vendor ID from "ITTIM Technology" to the list of
PCI Vendor IDs and lets the mt7921e driver bind to the mentioned wifi
chip.
Signed-off-by: Ingo Rohloff <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Extend settings of LED registers to support per-band configuration.
Signed-off-by: Jen-Hao Cheng <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add support to configure parameters at runtime, such as mcs, gi, and
he_ltf. Note that EHT mode does not support this feature yet.
Co-developed-by: MeiChia Chiu <[email protected]>
Signed-off-by: MeiChia Chiu <[email protected]>
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Only send commands that disable vif when removing interface, this
reduces some unnecessary bss_info and sta_rec commands, especially for
station interface.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
RX vector reports channel bandwidth 320-1 and 320-2 with different
values. Fix it to correctly report rx rate when using CBW320-2.
Fixes: 80f5a31d2856 ("wifi: mt76: mt7996: add support for EHT rate report")
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
According to P802.11be_D3.2 Table 9-404m, the minimum value of
Beamformee SS field shall be 3. Fix the values to follow the spec.
Fixes: 348533eb968d ("wifi: mt76: mt7996: add EHT capability init")
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The bf_num field represents how many bands can support beamform, so set
the value to 3, and bf_bitmap represents the bitmap of bf_num.
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Set correct wcid in txp to let the SDO hw module look into the correct
wtbl, otherwise the tx descriptor may be wrongly fiiled. This patch also
fixed the issue that driver could not correctly report sta statistics,
especially in WDS mode, which misled AQL.
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Co-developed-by: Michael-CY Lee <[email protected]>
Signed-off-by: Michael-CY Lee <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add more unified event IDs which will be used in new chipset.
This is the preliminary patch for mt7925 support.
Co-developed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add more unified command IDs which will be used in new chipset.
This is the preliminary patch for mt7925 support.
Co-developed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add tlv->data element for tlv parsing easier.
This is a preliminary patch to support mt7925 driver.
Co-developed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add eht field in struct mt76_power_limits for 802.11be power config.
The function stack size would be too big by eht adding in structure,
we also refactor mt76_connac_mcu_rate_txpower_band() to take dynamic
allocated memory instead.
This is a preliminary patch to support mt7925 driver.
Co-developed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add eht configuration support in existing function
mt76_connac_get_phy_mode_v2() and export it for mt7925.
This is a preliminary patch to support mt7925 driver.
Co-developed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt7925 rely on the similar functionalities in connac layer.
Export them for mt7925 reuse.
This is a preliminary patch to support mt7925 driver.
Co-developed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
add firmware download and dma init support for mt7925.
This is a preliminary patch to support mt7925 driver.
Co-developed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce is_mt7925() helper for new chipset. mt7925 runs the same
firmware download and mmio map flow as mt7921.
This is a preliminary patch to support mt7925 driver.
Co-developed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The error handling code was added in order to allow tx enqueue to fail after
calling .tx_prepare_skb. Since this can no longer happen, the error handling
code is unused.
Signed-off-by: Felix Fietkau <[email protected]>
In addition to the previous series I posted, over time I'd
also like to get rid of the iflist_mtx in mac80211. That
isn't easy now since lots of places use iteration and would
have to be audited, but even a cursory look suggests that
mt76 might be more problematic than most since holding the
wiphy lock for the latency-sensitive pre-TBTT work could be
an issue.
Convert the pre-TBTT work to use atomic iteration and then
sending the device commands outside of it.
Signed-off-by: Johannes Berg <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The hardware SDO has issue to fill txd for the moment, so fallback to
driver filling method.
Fixes: 98686cd21624 (wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices)
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
tx_rate can't be greater than 3 in mt76x0_phy_get_target_power routine
for cck rates. Get rid of dead code.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add support to report eht rx rate.
Note that extended fields for eht in mt76_rx_status will make the struct
size exceed the cb size, so make nss and band share the same u8.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When drv_tx calls race against local tx scheduling, the queue fill status checks
can potentially race, leading to dma queue entries being overwritten.
Fix this by deferring packets from drv_tx calls to the tx worker, in order to
ensure that all regular queue tx comes from the same context.
Signed-off-by: Felix Fietkau <[email protected]>
Enable receiving other-unicast packets
Disable RX header translation in order to proprerly receive data packets
Signed-off-by: Felix Fietkau <[email protected]>
Before preparing the new beacon, check the queue status, flush out all
previous beacons and buffered multicast packets, then (if necessary)
try to recover more gracefully from a stuck beacon condition by making a
less invasive attempt at getting the MAC un-stuck.
Fixes: c8846e101502 ("mt76: add driver for MT7603E and MT7628/7688")
Signed-off-by: Felix Fietkau <[email protected]>
Only trigger PSE reset if PSE was stuck, otherwise it can cause DMA issues.
Trigger the PSE reset while DMA is fully stopped in order to improve
reliabilty.
Fixes: c8846e101502 ("mt76: add driver for MT7603E and MT7628/7688")
Signed-off-by: Felix Fietkau <[email protected]>
It turns out that the code in mt7603_rx_pse_busy() does not detect actual
hardware hangs, it only checks for busy conditions in PSE.
A reset should only be performed if these conditions are true and if there
is no rx activity as well.
Reset the counter whenever a rx interrupt occurs. In order to also deal with
a fully loaded CPU that leaves interrupts disabled with continuous NAPI
polling, also check for pending rx interrupts in the function itself.
Fixes: c8846e101502 ("mt76: add driver for MT7603E and MT7628/7688")
Signed-off-by: Felix Fietkau <[email protected]>
Felix Fietkau