add .set_sar_specs to allow configuring SAR power limitations on the
frequency ranges from the userland.
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: YN Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The newer firmware requires host driver to set BA winsize
on both Tx/Rx sessions, so modify it for the long run.
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Sujuan Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix the following sparse warning in mt76x02_mac_write_txwi and
mt76x02_mac_tx_rate_val routines:
drivers/net/wireless/mediatek/mt76/mt76x02_mac.c:237:19:
warning: restricted __le16 degrades to intege
warning: cast from restricted __le16
drivers/net/wireless/mediatek/mt76/mt76x02_mac.c:383:28:
warning: incorrect type in assignment (different base types)
expected restricted __le16 [usertype] rate
got unsigned long
Fixes: db9f11d3433f7 ("mt76: store wcid tx rate info in one u32 reduce locking")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:114:10: error: implicit
conversion from enumeration type 'enum mt76_cipher_type' to different
enumeration type 'enum mcu_cipher_type' [-Werror,-Wenum-conversion]
return MT_CIPHER_NONE;
~~~~~~ ^~~~~~~~~~~~~~
drivers/net/wireless/mediatek/mt76/mt7921/mcu.c:114:10: error: implicit
conversion from enumeration type 'enum mt76_cipher_type' to different
enumeration type 'enum mcu_cipher_type' [-Werror,-Wenum-conversion]
return MT_CIPHER_NONE;
~~~~~~ ^~~~~~~~~~~~~~
Fixes: c368362c36d3 ("mt76: fix iv and CCMP header insertion")
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt7921 is mainly used in NB, CE and IoT application where battery life is
much concerned so the patch enabled PCIe ASPM by default to shut off the
clocks related PCIe as much as possible when MT7921 is either in suspend
state or in runtime pm to lower power consumption.
We still leave disable aspm as an option with module_param for users to
disable ASPM if necessary.
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The mistaken structure is introduced since we added the GTK rekey offload
to mt7663. The patch fixes mt76_connac_gtk_rekey_tlv structure according
to the MT7663 and MT7921 firmware we have submitted into
linux-firmware.git.
Fixes: b47e21e75c80 ("mt76: mt7615: add gtk rekey offload support")
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Leon Yen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
It will cause maximum connectable STA to be one less
when calling mt76_wcid_alloc with parameter MT7915_WTBL_STA - 1.
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Sujuan Chen <[email protected]>
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Zero out all the unused members of "req" so that we don't disclose
stack information.
Fixes: 495184ac91bb ("mt76: mt7915: add support for applying pre-calibration data")
Signed-off-by: Dan Carpenter <[email protected]>
Acked-by: Felix Fietkau <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
If total eeprom size is divisible by per-page size, the i in for loop
will exceed max page index, which happens in our newer chipset.
Fixes: 26f18380e6ca ("mt76: mt7915: add support for flash mode")
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix the following sparse warning in mt7615_mac_write_txwi routine:
drivers/net/wireless/mediatek/mt76/mt7615/mac.c:758:17:
warning: incorrect type in assignment
expected restricted __le32 [usertype]
got unsigned long
Fixes: 04b8e65922f63 ("mt76: add mac80211 driver for MT7615 PCIe-based chipsets")
Fixes: d4bf77bd74930 ("mt76: mt7615: introduce mt7663u support to mt7615_write_txwi")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix the following sparse warning in mt7921_update_txs routine:
drivers/net/wireless/mediatek/mt76/mt7921/mac.c:752:31:
warning: cast to restricted __le32
drivers/net/wireless/mediatek/mt76/mt7921/mac.c:752:31:
warning: restricted __le32 degrades to integer
Fixes: e5bca8c5d2cd3 ("mt76: mt7921: improve code readability for mt7921_update_txs")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix the following sparse warning in mt7915_mac_add_txs_skb routine:
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:1235:29:
warning: cast to restricted __le32
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:1235:23:
warning: restricted __le32 degrades to integer
Fixes: 3de4cb1756565 ("mt76: mt7915: add support for tx status reporting")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Do not grab the spinlock in mt7921_mcu_tx_done_event routine if not
necessary.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix endianness in mt7921_mcu_tx_done_event event reported by the
firmware.
Fixes: 3cce2b98e0241 ("mt76: mt7921: introduce mac tx done handling")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix the current driver mgmt frame is not respecting the basic rates field
provided by the AP and then unconditionally is using the lowest (1 or 6
Mbps) rate.
For example, if the AP only supported basic rate {24, 36, 48, 54} Mbps,
mt7921 cannot send mgmt frame with the rate not in the group. So,
instead, we pick up the lowest basic rate the AP can support to send.
Fixes: e57b7901469f ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Suggested-by: Ryder Lee <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix the current driver mgmt frame is not respecting the basic rates field
provided by the AP and then unconditionally is using the lowest (1 or 6
Mbps) rate.
For example, if the AP only supported basic rate {24, 36, 48, 54} Mbps,
mt7921 cannot send mgmt frame with the rate not in the group. So,
instead, we pick up the lowest basic rate the AP can support to send.
Fixes: 163f4d22c118 ("mt76: mt7921: add MAC support")
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
add mt76_default_basic_rate to mt76 core more devices can rely on
to send frames which require the rate in the basic rates.
Suggested-by: Ryder Lee <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
PHY offset in either .hw_value or .hw_value_short for mt7615, mt7663,
mt7915 and mt7921 device all start at bit 6, not 8.
Suggested-by: Ryder Lee <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Disable chip full reset just during device probing but allow
it during hw restart.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Set macwork timeout value according to runtime-pm in order to reduce
power consumption
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Allow the user to enable runtime-pm for mt7663s driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Similar to mt7663e, rely on mt76_connac_pm_ref/mt76_connac_pm_unref to
check PM state and increment/decrement wake counter
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
As already done for mt7921 and mt7663e, rely on pm reference counting in
drv/fw_own
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In order to support runtime-pm for sdio, do not run mt76_txq_schedule
directly, but schedule tx_worker instead
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Disable TWT REQ/RES mac capabilities since TWT is not supported
yet in mt7915/mt7921.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The iv from RXD is only for TKIP_RSC/CCMP_PN/GCMP_PN, and it needs a
check for CCMP header insertion. Move mt76_cipher_type to mt76.h to
reduce duplicated code.
Signed-off-by: Xing Song <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix the maximum size of the coredump generated with current mt7921
firmware. Otherwise, a truncated coredump would be reported to userland
via dev_coredumpv.
Also, there is an additional error handling enhanced in the patch to avoid
the possible invalid buffer access when the system failed to create the
buffer to hold the coredump.
Fixes: 0da3c795d07b ("mt76: mt7921: add coredump support")
Co-developed-by: YN Chen <[email protected]>
Signed-off-by: YN Chen <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce ds_enable switch to fully control fw deep_sleep capability
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Limit tx power for single-sku according to userlevel power.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7921_update_txs routine in order to improve code readability
for tx timestamp parsing/configuration.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When .sta_state is implemented, mac80211 assumes that the station entry is
usable after the NOTEXIST->NONE transition.
So we should create the sta entry as early as possible in order that
mac80211 pass assoc/auth frames to mt76 with the newly created sta entry,
and add .sta_assoc to mt76 core to refresh the sta entry again when sta is
being associated.
Fixes: 8aa5a9b7361c ("mt76: mt7921: enable deep sleep at runtime")
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The value of station mode is always 0.
Fixed: 00b2e16e0063 ("mt76: mt7915: add TxBF capabilities")
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
header files should use '/* SPDX ... */
Change from c file comment syle to header style
Signed-off-by: Tom Rix <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use mt7915_mcu_set_txbf() to reduce global functions. This can be
easily extended to support other TxBF commands in further patches.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Check device band capabilities before configuring single-sku
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In order to remove duplicated code, move mt76_get_next_pkt_id routine
in mt76.h
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Reduce rx buffer size to 2048 for mt7921/mt7915/mt7615 since we
now support rx amsdu offload
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Maximum interval (in seconds) for schedule scan plan supported by
the offload firmware can be U16_MAX.
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
FCS error packets are filtered by default and won't be reported to
driver, so that RX fcs error and PER in testmode always show zero.
Fix this issue by reading fcs error count from hw counter.
We did't fix this issue by disabling fcs error rx filter since it may
let HW suffer some SER errors.
Fixes: 5d8a83f09941 ("mt76: mt7915: implement testmode rx support")
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move chip-specific stats dumping part before common stats dumping
to provide flexibility for per-chip driver to modify the value of
common stats.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt76_connac_mcu_get_nic_capability utility routine to poll
device capabilities returned by mcu fw for CE devices (mt7663/mt7921).
This is a preliminary patch to introduce 6GHz support.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Make mt7921_set_channel routine static since it is only used in main.c
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
