When .sta_state is implemented, mac80211 assumes that the station entry is
usable after the NOTEXIST->NONE transition.
So we should create the sta entry as early as possible in order that
mac80211 pass assoc/auth frames to mt76 with the newly created sta entry,
and add .sta_assoc to mt76 core to refresh the sta entry again when sta is
being associated.
Fixes: 8aa5a9b7361c ("mt76: mt7921: enable deep sleep at runtime")
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The value of station mode is always 0.
Fixed: 00b2e16e0063 ("mt76: mt7915: add TxBF capabilities")
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
header files should use '/* SPDX ... */
Change from c file comment syle to header style
Signed-off-by: Tom Rix <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use mt7915_mcu_set_txbf() to reduce global functions. This can be
easily extended to support other TxBF commands in further patches.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Check device band capabilities before configuring single-sku
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In order to remove duplicated code, move mt76_get_next_pkt_id routine
in mt76.h
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Reduce rx buffer size to 2048 for mt7921/mt7915/mt7615 since we
now support rx amsdu offload
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Maximum interval (in seconds) for schedule scan plan supported by
the offload firmware can be U16_MAX.
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
FCS error packets are filtered by default and won't be reported to
driver, so that RX fcs error and PER in testmode always show zero.
Fix this issue by reading fcs error count from hw counter.
We did't fix this issue by disabling fcs error rx filter since it may
let HW suffer some SER errors.
Fixes: 5d8a83f09941 ("mt76: mt7915: implement testmode rx support")
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move chip-specific stats dumping part before common stats dumping
to provide flexibility for per-chip driver to modify the value of
common stats.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt76_connac_mcu_get_nic_capability utility routine to poll
device capabilities returned by mcu fw for CE devices (mt7663/mt7921).
This is a preliminary patch to introduce 6GHz support.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Make mt7921_set_channel routine static since it is only used in main.c
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Always wake the device up before dumping the single_sku power table
otherwise the device can hang.
Fixes: ea29acc97c555 ("mt76: mt7921: add dumping Tx power tabl")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Schedule power_save work running mt76_connac_pm_unref in order to reduce
power consumption
Tested-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Patch radar parameters to match the SDK to avoid possible false alarms.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Since now the fw reports tx rate events without polling,
mt7921_get_wtbl_info and related structures are no longer used.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Enable wep key hw offloading for sta mode. This patch fixes
WoW support for wep connections.
Tested-by: Deren.Wu <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
If efuse mode is used, read all values from fw during eeprom init,
which makes it more convinient to check if rf values in efuse are
properly burned.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Set MT76_RESET during mt7921_mac_reset in order to avoid packet
transmissions. Move tx scheduling at the end of reset routine.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
- Remove no-op code for queue lock/unlock, which is no longer needed
- Set a missing DMA flag
- Wait for full completion of error recovery before restarting tx
- Schedule IRQ tasklet to ensure that IRQ mask gets written
Signed-off-by: Felix Fietkau <[email protected]>
Move wiphy interface_modes configuration in mt76_alloc_device and
mt76_alloc_phy in order to be overwritten by hw specific code
since some drivers do not support all operating modes (mt7921
supports sta only in the current codebase)
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
wakeup chip every 250ms may cause huge power consumption
try to update statistic counter only if in active status only,
and it would lead fewer power cost
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Instead of read tx status from mac table, add new mechanisam to hanele
tx done event for data frame, every 250ms
This event indicate the real tx status of this pkt in mac layer and
would help mac80211 correct status more frequently
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Firmware functions (SCS, MU ...) also require read-clear phy counters,
hence firmware prepares a global task to read shared fields out to a
shared pool to avoid concurrency. Switch to event format accordingly.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Get rid of an undefined behaviour in mt76_testmode_alloc_skb routine
allocating skb frames
Fixes: 2601dda8faa76 ("mt76: testmode: add support to send larger packet")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Get rid of unnecessary function calls in mt76_testmode_free_skb routine
since they are already managed by dev_kfree_skb
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Free all pending frames in case of failure in mt76_testmode_alloc_skb
routine
Fixes: 2601dda8faa76 ("mt76: testmode: add support to send larger packet")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Get rid of unnecessary if condition in mt7615_add_interface routine
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Get per-rate txpower with mcu command. This is the preparation of
co-driver for the next chipset, which has different tmac power registers
but can share this same command.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
It's much more accurate than .get_tsf + .set_tsf and switch to use
mt76_rmw to operate tsf registers.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
It's much more accurate than .get_tsf + .set_tsf, and switch to use
mt76_rmw to operate tsf registers.
Tested-by: Xing Song <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This patch fixes a mcu hang during device probe on
Marvell ESPRESSObin after a hot reboot.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Return possible error values in mt7921_mac_init routine
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt7921 is mainly used in CE/IoT market so enable runtime-pm by default
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
OMAC idx have to be same with BSS idx according to firmware usage.
Fixes: e0f9fdda81bd ("mt76: mt7921: add ieee80211_ops")
Reviewed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: YN Chen <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
