There were a number of issues in the existing tx power handling code:
1. The EEPROM target power for chain 0 refers to the actual output power
after the channel and bandwidth delta have been added to the initial
channel gain. This means the delta values should not be added/subtracted
for the rate power calculation
2. When power is reduced significantly, the initial channel gain
underflows very quickly, while the per-rate power offsets are high.
This miscalculation causes effective tx power to be increased when it
should actually be lowered.
Fix this by trying to adjust the channel gain to the lowest power from
the rate table. In case of under- or overflow, compensate by adding an
appropriate delta to the rate power values.
This makes power configuration more accurate on a wider range of
configurable values
Signed-off-by: Felix Fietkau <[email protected]>
Allows the driver to control whether to send a BlockAckReq after waking
up. MT76x2 needs this set to true, for MT7603 it needs to be false
Signed-off-by: Felix Fietkau <[email protected]>
With software A-MPDU reordering in place, frames that notify mac80211 of
powersave changes are reordered as well, which can cause connection
stalls. Fix this by implementing powersave state processing in the
driver.
Signed-off-by: Felix Fietkau <[email protected]>
There is a possible race in mt76x2_stop_hardware() since pre_tbtt and
dfs tasklets could run during driver cleanup. Fix it disabling all
pending tasklets during device removal
Signed-off-by: Lorenzo Bianconi <[email protected]>
Apparently hardware does not perform CCMP PN validation in hardware, so
we need to take care of this in the driver.
Signed-off-by: Felix Fietkau <[email protected]>
Like beacons, probe responses need a hardware-generated TSF value. Set
the flag that causes the hw to generate it
Signed-off-by: Felix Fietkau <[email protected]>
Sending frames to mac80211 needs time, which could allow for more rx
packets to end up in the DMA ring. Retry polling until there are no more
frames left. Improves rx latency under load.
Signed-off-by: Felix Fietkau <[email protected]>
Fix hw queue configuration since mt76x2 devices use a reverse queue
enumeration respect to mac80211 one:
- 0: AC_BE
- 1: AC_BK
- 2: AC_VI
- 3: AC_VO
The issue can be reproduced sending two concurrent flow using
two separate queues:
- VO: 20Mbps UDP traffic
- BE: TCP traffic
In this scenario the UDP traffic will be blocked by the TCP one.
Fix it configuring properly WMM hw queue parameters
Fixes: 7bc04215a66b ("mt76: add driver code for MT76x2e")
Tested-by: Gaetano Catalli <[email protected]>
Signed-off-by: Gaetano Catalli <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Add mt76x2_dfs_set_domain routine in order to properly reconfigure
pattern detector when DFS domain has been changed
Signed-off-by: Lorenzo Bianconi <[email protected]>
Substitute tasklet_kill with tasklet_disable/tasklet_enable in order to
guarantee dfs tasklet can not be executed during dfs parameter
initialization
Signed-off-by: Lorenzo Bianconi <[email protected]>
drivers/net/wireless/mediatek/mt76/mt76x2_main.c:86:5-8: Unneeded variable: "ret". Return "0" on line 112
Remove unneeded variable used to store return value.
Generated by: scripts/coccinelle/misc/returnvar.cocci
Fixes: a5f6039c8f9c ("mt76: add driver code for MT76x2e")
CC: Felix Fietkau <[email protected]>
Signed-off-by: Fengguang Wu <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Fix typo in 5GHz power vs channel eeprom parsing
Fixes: 7bc04215a66b ("mt76: add driver code for MT76x2e")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Initialize mt76_txq pointer after ieee80211_txq pointer check.
Remove space after the pointer cast
Fixes: 7bc04215a66b ("mt76: add driver code for MT76x2e")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Currently if the allocation of skb fails and returns NULL then the
call to skb_put will cause a null pointer dereference. Fix this by
checking for a null skb and returning NULL. Note that calls to
function mt76x2_mcu_msg_alloc don't directly check the null return
but instead pass the NULL pointer to mt76x2_mcu_msg_send which
checks for the NULL and returns ENOMEM in this case.
Detected by CoverityScan, CID#1462624 ("Dereference null return value")
Fixes: 7bc04215a66b ("mt76: add driver code for MT76x2e")
Signed-off-by: Colin Ian King <[email protected]>
mt76x2_mac_start writes dev->rxfilter to the hardware. It also happens
during init, before dev->rxfilter is filled with the initval register
value, leading to issues like promisc mode being enabled
unconditionally.
Fix this by reading the default value into dev->rxfilter earlier
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Due to an unrelated issue, the MT_RX_FILTR_CFG_PROMISC flag is currently
unset, which means that monitor mode is unconditionally enabled.
Toggle this flag based on the mac80211 monitor mode setting instead
Signed-off-by: Felix Fietkau <[email protected]>
Felix Fietkau