Add mmio.c in order to use mt76_bus_ops throughout the driver.
It will be also shared with the future APSoC revision.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Frame reception timestamp (low 32-bits) that indicates the value of the
local TSF timer value at the time the first bit of the MAC header in the
received frame (PPDU unit) arriving at the MAC.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Reset wifi subsystem when MCU is already running.
Fixes firmware download failure after soft reboot on systems where the PCIe
reset could not be performed properly.
Signed-off-by: Ryder Lee <[email protected]>
Co-developed-by: Felix Fietkau <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
ieee80211_beacon_get_template() returns NULL when beacon state is disabled.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The same as mt7615. Keep BSS_INFO_BASIC enabled throughout interfaces
life cycle.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When disassociating and clearing the BSSID of a repeater entry used by a client
mode interface, the corresponding MAC address entry can get lost too, causing
the client interface to not be able to associate anymore.
Fix this by also refreshing the MAC address when setting the BSSID
Signed-off-by: Felix Fietkau <[email protected]>
Deleting a key with the previous key index deletes the current key
Rework the code to better keep track of multiple keys and check for the
key index before deleting the current key
Signed-off-by: Felix Fietkau <[email protected]>
ieee80211_register_hw() is called with rtnl_lock held, and this could be
caused lockdep from a work item that's on a workqueue that is flushed
with the rtnl held.
Move mt7915_register_ext_phy() outside the init_work().
Signed-off-by: Evelyn Tsai <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Properly check returned values from mcu utility routines in
mt7915_ops.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Avoid directly updating sinfo->rxrate from firmware since rate_info might
be overwritten by wrong results even mt7915_mcu_get_rx_rate() fails check.
Add more error handlings accordingly.
Fixes: 11553d88d0b9 ("mt76: mt7915: query station rx rate from firmware")
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In order to properly report MIB counters to mac80211, resets stats in
mt7915_get_stats routine() and hold mt76 mutex accessing MIB counters.
Sum up MIB counters in mt7915_mac_update_mib_stats routine.
Fixes: c6b002bcdf ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Similar to mt7921, fix 802.11 aggr len debugfs reporting for mt7915 driver.
Fixes: e57b7901469fc ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
clang points out a possible corner case in the mt7915_tm_set_tx_cont()
function if called with invalid arguments:
drivers/net/wireless/mediatek/mt76/mt7915/testmode.c:593:2: warning: variable 'mode' is used uninitialized whenever switch default is taken [-Wsometimes-uninitialized]
default:
^~~~~~~
drivers/net/wireless/mediatek/mt76/mt7915/testmode.c:597:13: note: uninitialized use occurs here
rateval = mode << 6 | rate_idx;
^~~~
drivers/net/wireless/mediatek/mt76/mt7915/testmode.c:506:37: note: initialize the variable 'mode' to silence this warning
u8 rate_idx = td->tx_rate_idx, mode;
^
Change it to return an error instead of continuing with invalid data
here.
Fixes: 3f0caa3cbf94 ("mt76: mt7915: add support for continuous tx in testmode")
Signed-off-by: Arnd Bergmann <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
For AP and Client mode, the hardware can pass received packets as 802.3 frames
that can be passed to the network stack as-is.
Signed-off-by: Felix Fietkau <[email protected]>
Enable hw rx-amsdu de-aggregation support available in 7915 devices.
This is a preliminary patch to enable rx checksum offload
Signed-off-by: Lorenzo Bianconi <[email protected]>
Set MT_PHY_TYPE_OFDM as default value for mode variable in
mt7915_tm_set_tx_cont routine in order to proper initialize it even
for default case.
Fixes: 3f0caa3cbf94: "mt76: mt7915: add support for continuous tx in testmode"
Reported-by: Dan Carpenter <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
As done for mt76_connac_mcu_alloc_wtbl_req, even if this is not a real
bug since mt7915_mcu_alloc_wtbl_req routine can fails just if nskb is NULL,
always check return value from mt7915_mcu_alloc_wtbl_req in order to avoid
possible future mistake.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The first pointer in the txp needs to be unmapped as well, otherwise it will
leak DMA mapping entries
Fixes: 27d5c528a7ca ("mt76: fix double DMA unmap of the first buffer on 7615/7915")
Signed-off-by: Felix Fietkau <[email protected]>
For performance reasons, mt7915 supports using 2 PCIE gen1 links on
platforms that don't support gen2.
Add support for using this to move traffic for a second DBDC band onto
a dedicated link
Signed-off-by: Felix Fietkau <[email protected]>
Since vif indexes are per-phy, we need to factor in the phy index to avoid
collisions on the WTBL index
Signed-off-by: Felix Fietkau <[email protected]>
With this patch, TxBF can be run on both bands simultaneously.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When the EEPROM band fields contain default values, assign 2.4 GHz to the
first band and 5 GHz to the second.
Signed-off-by: Felix Fietkau <[email protected]>
It causes high CPU load on the WA core, which can lead to extra latency when
using many stations. Dropping packets for long queues is managed by mac80211
fq_codel instead
Signed-off-by: Felix Fietkau <[email protected]>
Add support for passing flags for selecting the MCU target and query type
instead of trying to detect it based on the command id
Signed-off-by: Felix Fietkau <[email protected]>
