Overwriting the RMAC_CHFREQ register is not reliable enough, as the firmware
could potentially write it again.
Since there is no PHY index indication in the rx info, we need to use another
way:
If both PHYs are using different channels, find the PHY where chfreq matches
the register value.
The only corner case remaining is when both PHYs are using the same channel.
In that case, the per-packet noise value on the primary PHY will have
information belonging to the chains of the secondary PHY from the previous
received packet of that PHY. The secondary PHY will set noise to 0 for extra
chains.
Signed-off-by: Felix Fietkau <[email protected]>
Unify code converting between the different txpower values. Always add/remove
the combined txpower delta before dividing half-dB values.
Also fix the combined txpower delta values. The correct half-dB delta for
3 chains is 9, not 8.
Signed-off-by: Felix Fietkau <[email protected]>
Fix the following sparse warning in mt7615_write_hw_txp:
warning: incorrect type in assignment (different base types)
expected restricted __le16
got unsigned long
Signed-off-by: Lorenzo Bianconi <[email protected]>
Do not set the tx/rx start bits in MT_MAC_SYS_CTRL from within initvals.
The driver sets these later when the hardware is ready
Signed-off-by: Felix Fietkau <[email protected]>
In order to reduce command/event times, newer firmware adds a tag
sta_rec_wtbl to take care of WTBL operations.
MCU_EXT_CMD_WTBL_UPDATE is deprecated.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Tested-by: Sean Wang <[email protected]>
Add fw_ver in mt7615_dev to check firmware version, and adjust
mt7615_mcu_send_sta_rec() to adapt firmware v2 changes.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Tested-by: Sean Wang <[email protected]>
The second PHY receives no packets unless there is an active vif present.
Set the WANT_MONITOR_VIF flag to deal with that
Signed-off-by: Felix Fietkau <[email protected]>
Send an undersized corrupt packet to the DMA queue, which causes the
firmware to issue a full chip reset
Signed-off-by: Felix Fietkau <[email protected]>
When the firmware detects a problem, it needs the host to stop/reset DMA and
resume it again when the hardware state has been reset.
Signed-off-by: Felix Fietkau <[email protected]>
Setting the tx power by manipulating EEPROM may in some cases not be enough,
since it only covers the base target power and not per-rate offsets.
In other cases, it could limit tx power of rates too much, possibly reducing
throughput or range.
Use firmware support for applying per-rate limit and power offsets for
different values of Nss.
Signed-off-by: Felix Fietkau <[email protected]>
MT7622 does not have the CR4 microcontroller sitting in the data path.
Because of that, it uses the chip's native tx descriptor format instead of
something parsed and converted by the firmware.
Co-developed-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
MT7622 does not have a CR4 microcontroller, so it only uses its own N9
firmware.
Co-developed-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When sending EEPROM data to the MCU, MT7622 uses a longer buffer
Co-developed-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
MT7622 queue mapping is different from MT7615 and requires an extra dma
scheduler init and a few register tweaks
Co-developed-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
MT7622 uses more interrupt bits for queue tx completion events.
Enabling those extra bits is harmless on MT7615
Co-developed-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The beginning of the struct is guaranteed to be 4-byte aligned, and this
attribute allows the compiler to generate more efficient code
Signed-off-by: Felix Fietkau <[email protected]>
Define MT_DRV_RX_DMA_HDR flag in drv_flag in order to not skip rx frame
dma header since new devices (e.g. mt7663u) reports rx frame info in the
usb dma header
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt76u_skb_dma_info utility routine in mt76-usb module in order
to be reused adding mt7663u support
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
7663u devices rely on a different endpoint mapping. Take it into account
in mt76u_alloc_tx routine
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce extended utility routines to read/write data o usb bus. New
devices (e.g. mt7663u) will rely on both upper and lower part of the
register address. Add ext parameter to mt76u_init signature in order to
reuse the code adding mt7663u support.
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add mt76u_alloc_mcu_queue utility routine to allocate mcu hw rx queue.
This is a preliminary patch to support new devices (e.g. mt7663u) that
rely on a hw queue for mcu messages
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Resume all possible rx queues after suspend. This is a preliminary patch
to support mt7663u devices
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add mt76_queue parameter to mt76u_rx_urb_alloc signature since this
routine will be used to allocate urbs for mcu hw queue used by new
chipset generation (e.g. mt7663u). Check sg_max_size in in
mt76u_urb_alloc in order to use linear urb for mcu queue
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt76u_alloc_rx_queue routine to allocate rx hw queue.
This is a preliminary patch to support new devices (e.g. mt7663u) that
rely on a hw queue for mcu messages
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Stop/free all configured rx queues (data/mcu) in
mt76u_stop_rx/mt76u_free_rx. This is a preliminary patch to support new
devices (e.g. mt7663u) that rely on a hw queue for mcu messages
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt76u_free_rx_queue utility routine to free rx hw queue.
This is a preliminary patch to support new devices (e.g. mt7663u) that
rely on a hw queue for mcu messages
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mcu buffer allocation in mt76x2u/mt76x0u drivers since newer
chipsets (e.g. mt7663u) does not rely on synchronous mcu communication
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Felix Fietkau