Sicne the mapping is global, mapped register access needs to be protected
against concurrent access, otherwise a race condition might cause the reads
or writes to go towards the wrong register
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Do not clear the interrupt mask register on MT7915, since that prevents
MCU_CMD interrupts from being reported, thus causing timeouts during the
reset sequence. Defer stopping WED until tx/rx processing activity has
stopped.
Signed-off-by: Felix Fietkau <[email protected]>
The PPDU TxS does not include the error bit so it cannot use to report
status to mac80211.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When using fixed rate, HW uses txd DW9 to store tx arrivial time if VTA
is set. It would overwrite the msdu_id in txd and lead to token pending
if amsdu is enable.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix additional shift overflow warning on 32 bit systems for mt7996 mac.c
source.
Fixes: 95c14207d2 ("wifi: mt76: mt7996: set DMA mask to 36 bits for boards with more than 4GB of RAM")
Signed-off-by: Christian Marangi <[email protected]>
If WED rx is enabled, rx buffers are added to a buffer pool that can be
filled from multiple page pools. Because buffers freed from rx poll are
not guaranteed to belong to the processed queue's page pool, lockless
caching must not be used in this case.
Cc: [email protected]
Fixes: 2f5c3c77fc9b ("wifi: mt76: switch to page_pool allocator")
Signed-off-by: Felix Fietkau <[email protected]>
To avoid using incorrect 6g power settings after disconnection,
it should to update back to the default state when disconnected.
Fixes: 51ba0e3a15eb ("wifi: mt76: mt7921: add 6GHz power type support for clc")
Signed-off-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When enter suspend/resume while in a connected state, the upper layer
will trigger disconnection before entering suspend, and at the same time,
it will trigger regd_notifier() and update CLC, causing the CLC event to
not be received due to suspend, resulting in a command timeout.
Therefore, the update of CLC is postponed until resume, to ensure data
consistency and avoid the occurrence of command timeout.
Fixes: 4fc8df50fd41 ("wifi: mt76: mt7921: get regulatory information from the clc event")
Signed-off-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Due to the increase in the number of power tables for 6Ghz on CLC,
the variable nr_country is no longer sufficient to represent the
total quantity. Therefore, we have switched to calculating the
length of clc buf to obtain the correct power table. Additionally,
the version number has been incremented to 1.
Fixes: 23bdc5d8cadf ("wifi: mt76: mt7921: introduce Country Location Control support")
Signed-off-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
We actually don't need the reserve the 512 entries for the MCU firmware
download Rx queue because the queue was only used in the firmware download
phase to save the most of space and the reduction can significantly help
with reducing latency we spent by ~20% further in resetting the Rx queue
as the device was waking up from deep sleep mode.
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The ieee80211_queue_work function queues work into the mac80211
local->workqueue, which is widely used for mac80211 internal
work processes. In the mt76 driver, both the mt76-sido-status and
mt76-sdio-net threads enqueue workers to the workqueue with this
function. However, in some cases, when two workers are enqueued
to the workqueue almost simultaneously, the second worker may not
be scheduled immediately and may get stuck for a while.
This can cause timing issues. To avoid these timing
conflicts caused by worker scheduling, replace the worker
with an independent thread.
Fixes: 48fab5bbef40 ("mt76: mt7921: introduce mt7921s support")
Signed-off-by: Wang Zhao <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix tag endianness in mt7996_mcu_wed_rro_event routine
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rename mtk_rxbm_desc structure in mtk_wed_bm_desc since it will be used
even on tx side by MT7988 SoC.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
Get rid of nl80211_iftype from mt7925_init_eht_caps routine signature
since it is not actually used.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add MT_TXD6_MSDU_CNT_V2 bitfield, which is used by mt7992 chipsets.
This is a preliminary patch for mt7992 chipsets support.
Signed-off-by: Benjamin Lin <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
MT7992 chipsets support up to 32 interfaces (with maximum 19 per-band)
and 512 station entries.
This is a preliminary patch for mt7992 chipsets support.
Signed-off-by: StanleyYP Wang <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add the default eeprom and 0x7992 check to mt7996_check_eeprom().
This is a preliminary patch for mt7992 chipsets support.
Signed-off-by: StanleyYP Wang <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add mt7992_offs to differentiate registers that share the same
definitions with mt7996 chipsets but have differnet offsets.
This is a preliminary patch for mt7992 chipsets support.
Signed-off-by: StanleyYP Wang <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add DMA TX/RX queues and RRO init flow for mt7992 chipsets.
This is a preliminary patch for mt7992 chipsets support.
Co-developed-by: StanleyYP Wang <[email protected]>
Signed-off-by: StanleyYP Wang <[email protected]>
Co-developed-by: Shayne Chen <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Benjamin Lin <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Support firmware download and enable related AFE PLL for mt7992 chipsets.
This is a preliminary patch for mt7992 chipsets support.
Co-developed-by: Benjamin Lin <[email protected]>
Signed-off-by: Benjamin Lin <[email protected]>
Co-developed-by: Shayne Chen <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: StanleyYP Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Replace dbdc_support and tbtc_support with mt7996_band_valid() to
support mt7996 variants with band0/band2 dual-band support.
This changes reduces ambiguity when checking supported bands on different
variants or new chipsets, as well as during the init configurations on
DMA TX/RX queues or irq masks.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The internal struct and union inside mt7996_mcu_all_sta_info_event is
marked as being aligned, which conflicts with it being unaligned
within that structure:
drivers/net/wireless/mediatek/mt76/mt7996/mcu.h:165:2: error: field within 'struct mt7996_mcu_all_sta_info_event' is less aligned than 'union mt7996_mcu_all_sta_info_event::(anonymous at ../drivers/net/wireless/mediatek/mt76/mt7996/mcu.h:165:2)' and is usually due to 'struct mt7996_mcu_all_sta_info_event' being packed, which can lead to unaligned accesses [-Werror,-Wunaligned-access]
Mark all three as being packed as well to ensure byte packing for
the entire thing.
Fixes: adde3eed4a75 ("wifi: mt76: mt7996: Add mcu commands for getting sta tx statistic")
Signed-off-by: Arnd Bergmann <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Just like MT7916 also MT7981 can handle 3T3R DBDC frontend and should
hence be included in the corresponding conditional expression in the
driver. Add it.
Fixes: 6bad146d162e ("wifi: mt76: mt7915: add support for MT7981")
Signed-off-by: StanleyYP Wang <[email protected]>
Signed-off-by: Daniel Golle <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The offset of the TSSI flag on the EEPROM of MT7981 devices was wrong.
Set the correct offset instead.
Fixes: 6bad146d162e ("wifi: mt76: mt7915: add support for MT7981")
Signed-off-by: StanleyYP Wang <[email protected]>
Signed-off-by: Daniel Golle <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add a BSS eht_support check before returning EHT phy mode. Without this
patch, there might be an inconsistency where the softmac layer thinks
the BSS is in HE mode, while the FW thinks it is in EHT mode.
Signed-off-by: MeiChia Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Implement beacon protection feature for mt7996 chipsets, and also do
some cleanup on the set key routine.
Co-developed-by: Rudra Shahi <[email protected]>
Signed-off-by: Rudra Shahi <[email protected]>
Signed-off-by: Allen Ye <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add sta_rec_ht_uni struct to pass HT ampdu params to firmware. For VHT,
HE, and EHT mode, firmware will get the ampdu params by parsing the
corresponding capability.
Co-developed-by: Shayne Chen <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
During runtime, the GI value in the WTBL is not updated in real-time. To
obtain the latest results for the TX GI, switch to use an MCU command.
Signed-off-by: Benjamin Lin <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The power gain value is related to total TX path, so change the
calculation to use per-phy chainmask.
Signed-off-by: Allen Ye <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use per-phy structure for maximum txpower value initializing, since each
phy may have a different chainmask, which can impact the calculation of
power gain.
Co-developed-by: Allen Ye <[email protected]>
Signed-off-by: Allen Ye <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
For UBPR and FILS frames, the BSS_CHANGED_BEACON flag will also be set,
which causes those frames to use the beacon rate in TX descriptors.
Adjust the statement to fix this issue.
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: MeiChia Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use the new fixed rate command format to let the fixed field function
work normally.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Make mt7996_mcu_set_fixed_field() non-static in order to handle
IEEE80211_RC_SMPS_CHANGED in mt7996_mac_sta_rc_work().
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Always set the fixed_bw bitfield for fixed rate frames to keep it being
sent with specific bandwidth. Without this change, the bw of fixed rate
frames will still be decided by hardware.
Reported-by: Chank Chen <[email protected]>
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Refactor and update dma prefetch parts and also split band 1 traffic to
PCIe 1 to enhance throughput.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
For connac3 chipsets, setting of spe_idx is moved from TX descriptor to
the fixed rate table. This patch implements the setting to support
duplicate TX mode for beacon.
Signed-off-by: StanleyYP Wang <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This patch adds support for thermal sensor device, including the
following features:
- Support to read current chip temperature.
- Support to set/get the trigger/restore temperature for thermal service.
- Support to read current chip tx cycle.
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
