When receiving a 4 address non-AMSDU packet, there is no bssid in the
address fields, which breaks powersave handling for 4-address peers.
Set the mcu command to use A1 as bssid when receiving 4 address
non-AMSDU packets on mt7992 and mt7990.
Also skip mt7996_mac_init_band() for invalid bands, so the command is
only sent for bands that actually exist on the device.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Problem:
MCU command timeout while the firmware state is normal, and the
firmware keeps showing the error log "ERROR!! NO PAUSE...".
Root cause:
If the MLD_ID field in the TXD is neither the primary link id nor the
secondary link id, it may lead to a firmware busy loop when the third
link is in power saving mode.
Remap frames directed to a third link to the primary link wcid. Since
TX status events and txfree completions carry the wcid the firmware
saw, use the remapped wcid for packet id tracking and non-AQL packet
accounting as well, while the frame keeps its original link context
for addressing, band and OMAC selection.
Fixes: 85cd5534a3f2 ("wifi: mt76: mt7996: use correct link_id when filling TXD and TXP")
Signed-off-by: Peter Chiu <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Skip WFSYS reset during bootup for MT7990 chipsets; only reset if L0.5
recovery is triggered.
Without this fix, the following kernel error may occur:
Internal error: synchronous external abort.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Enable VTA flag in txwi to enable HQD in SPL which is needed by
the PST. Without this patch, PST cannot get the correct delay of
TxD and lead to a large latency.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Set MT_WF_RFCR_DROP_OTHER_UC by default and disable this flag in
mt7996_set_monitor only if monitor mode is enabled.
Without this patch, the MT_WF_RFCR_DROP_OTHER_UC would not be set so the
driver would receive lots of packets meant for other devices.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The maximum TX path and NSS may differ on a band. For example, one variant
of the MT7992 has 5 TX paths and 4 NSS on the 5 GHz band. To address this,
add orig_antenna_mask to record the maximum NSS and prevent setting an
invalid NSS in mt7996_set_antenna().
Fixes: 69d54ce7491d ("wifi: mt76: mt7996: switch to single multi-radio wiphy")
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Set the max AMPDU length in the EHT MAC CAP. Without this patch, the
peer station cannot obtain the correct capability, which prevents
achieving peak throughput on the 2 GHz band.
Fixes: 1816ad9381e0 ("wifi: mt76: mt7996: add max mpdu len capability")
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
The non-AP interfaces would not use conf->vht_ldpc so they never set
STA_CAP_VHT_LDPC even if peer-station support LDPC.
Check conf->vht_ldpc only for AP interface.
Without this patch, station only uses BCC to transmit packet in VHT mode.
Fixes: dda423dd65c3 ("wifi: mt76: mt7996: remove mt7996_mcu_beacon_check_caps()")
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Set max mpdu len to 11454 according to hardware capability.
Without this patch, the max ampdu length would be 3895 and count not get
expected performance.
Fixes: 348533eb968d ("wifi: mt76: mt7996: add EHT capability init")
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
According to connac3 HW design, the WMM index of AP and STA interface
should be 0 and 3, respectively.
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
During scanning, UNI_CHANNEL_RX_PATH tag is necessary for the firmware to
properly stop and resume MAC TX queue. Without this tag, HW needs more time
to resume traffic when switching back to working channel.
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
The chainmask is u16 so using hweight8 cannot get correct tx_ant.
Without this patch, the tx_ant of band 2 would be -1 and lead to the
following issue:
BUG: KASAN: stack-out-of-bounds in mt7996_mcu_add_sta+0x12e0/0x16e0 [mt7996e]
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Set RCPI values in mt7996_mcu_sta_rate_ctrl_tlv(), which can make the
FW rate control algorithm be initialized with a better MCS selection
table.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add pre-calibration for mt7986 and mt7916. It has different data size
with mt7915. Group cal needs 54k and 94k for 2G + 5G and 2G + 6G,
respectively. DPD cal needs 300k.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: StanleyYP Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The mcu command format are different for mt7915 and mt7986.
Fix the mt7915_mcu_wed_wa_tx_stats to support mt7915 and mt7986.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
DMA queue settings of TXS will be initialized by the firmware.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This patch fixes the following TWT issues:
- Change table_mask to u16 to support up to 16 TWT stations
- Reject TWT flows for duplicated establishment
- Fix possible unaligned pointer
- Remove unsupported TWT_CONTROL_WAKE_DUR_UNIT flag
- The minimum TWT duration supported by mt7996 chipsets is 64. Reply
with TWT_SETUP_CMD_DICTATE if the min_twt_dur is smaller than 64
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The PPDU TXS does not include the error bit so it cannot use to report
status to mac80211. This patch fixes issue that STA wrongly detects if AP
is still alive.
Fixes: 2569ea5326e2 ("wifi: mt76: mt7996: enable PPDU-TxS to host")
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The PPDU TxS does not include the error bit so it cannot use to report
status to mac80211.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When using fixed rate, HW uses txd DW9 to store tx arrivial time if VTA
is set. It would overwrite the msdu_id in txd and lead to token pending
if amsdu is enable.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add sta_rec_ht_uni struct to pass HT ampdu params to firmware. For VHT,
HE, and EHT mode, firmware will get the ampdu params by parsing the
corresponding capability.
Co-developed-by: Shayne Chen <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use the new fixed rate command format to let the fixed field function
work normally.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Make mt7996_mcu_set_fixed_field() non-static in order to handle
IEEE80211_RC_SMPS_CHANGED in mt7996_mac_sta_rc_work().
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Refactor and update dma prefetch parts and also split band 1 traffic to
PCIe 1 to enhance throughput.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Set mpdu density to 2 usec for non-mt7915 Wi-Fi 6 generation chipsets
to align to the hardware capability which improves the throughput.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Do not report cca and csa finish to upper layer on station type vif to
prevent warnings caused by setting beacon.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
RX vector reports channel bandwidth 320-1 and 320-2 with different
values. Fix it to correctly report rx rate when using CBW320-2.
Fixes: 80f5a31d2856 ("wifi: mt76: mt7996: add support for EHT rate report")
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Set correct wcid in txp to let the SDO hw module look into the correct
wtbl, otherwise the tx descriptor may be wrongly fiiled. This patch also
fixed the issue that driver could not correctly report sta statistics,
especially in WDS mode, which misled AQL.
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Co-developed-by: Michael-CY Lee <[email protected]>
Signed-off-by: Michael-CY Lee <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
There's a race between driver and fw on some tx/rx control registers
when setting ifs, which will cause accidental hw queue pause problems.
Avoid this by setting ifs time with bss_info mcu command.
Reviewed-by: Shayne Chen <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Set SUPPORTS_VHT_EXT_NSS_BW to let the max BW capability correctly be
parsed by different devices.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The bmc_tx_wlan_idx should be the wlan_idx of the current bss rather
than peer AP's wlan_idx, otherwise there will appear some frame
decryption problems on station mode.
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Reviewed-by: Shayne Chen <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add FW_START_WORKING_PDA_DSP for the indication of starting DSP
firmware download, which is for phy-related control.
The firmware is transparent to the driver, but it's necessary for the
firmware download process.
Reviewed-by: Shayne Chen <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
AQL relies on accurate tx rate reporting, so add this patch for
non-binding skb rate when WED is enabled.
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Concurrent binding/non-binding skbs could be handled anywhere which leads
to mixed byte counting, so switch to use PPDU TxS reporting regardless Tx
paths when WED is active.
Fixes: 43eaa3689507 ("wifi: mt76: add PPDU based TxS support for WED device")
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
PPDU TxS can only report MPDU count whereas mac80211 requires MSDU scale
(NL80211_STA_INFO_TX_PACKETS), so switch to get MSDU counts from WA
statistic.
Note that mt7915 WA firmware only counts tx_packet for WED path, so driver
needs to take care of host path additionally.
Fixes: 43eaa3689507 ("wifi: mt76: add PPDU based TxS support for WED device")
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Currently using BSS_INFO_PS command will sometimes cause packet drop in
hw rx queue.
Temporarily remove this function until finding the cause.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Init mpdu density based on the hardware capability to prevent rx drop.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix the tail and data pointers. The rxd->len in mt7996_mcu_rxd does not
include the length of general rxd. It only includes the length of
firmware event rxd. Use skb->length to get the correct length.
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The scatter and gather frame may be incorrect because WED and WO may
send frames to host driver interleaved.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Sujuan Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Enable RED to limit the number of token used by each band. If single band
uses too many tokens, it would hurt the throughput of the other bands.The
software path can solve this problem by AQL so enable RED for HW path only.
Reviewed-by: Shayne Chen <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Set sku initial value before mcu starts to prevent mcu from getting an
invalid value.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
A variant of mt7916 supports up to 3 tx/rx paths but with only
2 spatial streams. An example usage of the 3rd path is to server as
an auxiliary for beamforming.
In order to deal with this case, this patch reworks some parts to
correctly use paths or streams.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The minimum twt duration supported by mt7915 is 64 according to hardware
design. Reply station with TWT_SETUP_CMD_DICTATE if min_twt_dur smaller
than 64.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Reject twt flows with the same parameters to prevent some potential issues
causing by duplicated establishment.
Reviewed-by: Ryder Lee <[email protected]>
Reviewed-by: Shayne Chen <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt7915 can support 16 twt stations so modify table_mask to u16.
Fixes: 3782b69d03e7 ("mt76: mt7915: introduce mt7915_mac_add_twt_setup routine")
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This patch fixes performance issue of beamforming tx on
bandwidth 160MHz.
Fixes: 99ad32a4ca3a ("mt76: mt7915: add support for MT7986")
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The maximum max_mpdu_size of mt7915 is 7991, whereas mt7916 can
support 11454.
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Should use peer's bandwidth instead of chandef->width to
get correct mcs_map.
Fixes: 76be6c076c077 ("mt76: mt7915: add .set_bitrate_mask() callback")
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The mcs value of HT mode reported by mt7921_mac_add_txs_skb()
has already been converted to the expected format.
Fixes: 970ab80ef9f63 ("mt76: mt7921: report tx rate directly from tx status")
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The mcs value of HT mode reported by mt7915_mac_add_txs_skb()
has already been converted to the expected format.
Fixes: 9908d98ae72cd ("mt76: mt7915: report tx rate directly from tx status")
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
ieee80211_register_hw() is called with rtnl_lock held, and this could be
caused lockdep from a work item that's on a workqueue that is flushed
with the rtnl held.
Move mt7615_register_ext_phy() outside the init_work().
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
