WED support requires using non-coherent DMA, whereas the PCI device might
be configured for coherent DMA.
The WED driver will take care of changing the PCI HIF coherent IO setting
on attach.
Signed-off-by: Felix Fietkau <[email protected]>
Soft reboot might not clear certain condition, so always call
mt7915_wfsys_reset() during init.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Honor runtime-pm user configuration in mt7921_sniffer_interface_iter
routine if we do not have a monitor interface.
Fixes: 1f12fa34e5dc5 ("mt76: mt7921: don't enable beacon filter when IEEE80211_CONF_CHANGE_MONITOR is set")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt7921 is currently using rxfilter defined in mt76_dev for rx filter
configuration. Fix mt7921_configure_filter implementation.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
MT7915_MAX_INTERFACES is per-band declaration in MT7915/MT7986/MT7916.
Enlarge vif_mask to 64 bits wide, including the bit operation.
Reviewed-by: Shayne Chen <[email protected]>
Signed-off-by: Evelyn Tsai <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Clean up and fix error paths in mt7915_register_device
Initialize second DBDC tx queue in mt7915_dma_init
Signed-off-by: Felix Fietkau <[email protected]>
Instead of taking q->lock for every single cleaned up frame, batch up to
16 cleaned up frames before taking it.
Signed-off-by: Felix Fietkau <[email protected]>
dma unmap is already needed for cleanup anyway, so we don't need the extra
tracking and can save a bit of memory here
Signed-off-by: Felix Fietkau <[email protected]>
When setup monitor mode in DFS channel, mt76 send CH_SWITCH_DFS to
fw for channel config. This would cause rx performance bad while
monitoring frames. Settings CH_SWITCH_NORMAL in monitor mode would
get the same performance as normal channels.
Reviewed-by: Shayne Chen <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
IEEE80211_CONF_CHANGE_MONITOR would be set every time even when vif runs as
sta mode.
If vif runs as sta mode, the beacon filter would be falsely enabled
earlier than the associated state.
That is not the behavior the firmware expects and also breaks the original
logic of sta mode. Thus, we only limit the operation to set the beacon
filter only for monitor mode when IEEE80211_CONF_CHANGE_MONITOR is set.
Fixes: 4ad65a54617c ("mt76: mt7921: toggle runtime-pm adding a monitor vif")
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Due to the missing IEEE80211_RADIOTAP_HE_DATA1_BW_RU_ALLOC_KNOWN in
status report, the HE rate in wirehsark/tcpdump always shows wrong value.
Applications will refer to IEEE80211_RADIOTAP_HE_DATA5_DATA_BW_RU_ALLOC
when the flag is set and shows the correct data rate.
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Firmware initialization can take a while. Move mt7921_init_hw routine in
a dedicated work in order to not slow down bootstrap process.
Tested-by: Deren Wu <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce __mt76u_init unitility routine and move mt7615 usb bus ops
into mt7615 module in order to allow specifying driver specific
parameter.
This is a preliminary patch to add usb support to mt7921 driver.
Tested-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to add usb support to mt7921 driver.
Tested-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to add usb support to mt7921 driver.
Tested-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Various spelling mistakes in comments.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This patch fixes performance issue of beamforming tx on
bandwidth 160MHz.
Fixes: 99ad32a4ca3a ("mt76: mt7915: add support for MT7986")
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Some of beamforming mib counters are moved to different offsets
or registers in newer chipsets.
Fixes: 99ad32a4ca3a ("mt76: mt7915: add support for MT7986")
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Drop invalid rssi value to calculate a reasonable report
Fixes: 4550fb9e9810 ("mt76: improve signal strength reporting")
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Switch to use le32/16_get_bits() to simplfy codes and specify
the size explicitly to avoid potential issues.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Don't populate the read-only array ba_range on the stack but
instead make it static const. Also makes the object code a little
smaller.
Signed-off-by: Colin Ian King <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
If devm_pinctrl_get() fails then it leads to an error pointer
dereference. Add a check to prevent that.
Fixes: 99ad32a4ca3a ("mt76: mt7915: add support for MT7986")
Signed-off-by: Dan Carpenter <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
A-die 7976 has different offset and uses different channel group
definition on txpower init values.
Fixes: 99ad32a4ca3a ("mt76: mt7915: add support for MT7986")
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: MeiChia Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Since there are no HT & VHT IEs being sent in 6ghz,
some capabilities judgement and parsing for wtbl &
starec configuration should be modified to reflect such changes.
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Money Wang <[email protected]>
Signed-off-by: MeiChia Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This improves rate reach performance on units with polarized antennas.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt7921s driver may receive frames with fragment buffers. If there is a
CTS packet received in monitor mode, the payload is 10 bytes only and
need 6 bytes header padding after RXD buffer. However, only RXD in the
first linear buffer, if we pull buffer size RXD-size+6 bytes with
skb_pull(), that would trigger "BUG_ON(skb->len < skb->data_len)" in
__skb_pull().
To avoid the nonlinear buffer issue, enlarge the RXD size from 128 to
256 to make sure all MCU operation in linear buffer.
[ 52.007562] kernel BUG at include/linux/skbuff.h:2313!
[ 52.007578] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
[ 52.007987] pc : skb_pull+0x48/0x4c
[ 52.008015] lr : mt7921_queue_rx_skb+0x494/0x890 [mt7921_common]
[ 52.008361] Call trace:
[ 52.008377] skb_pull+0x48/0x4c
[ 52.008400] mt76s_net_worker+0x134/0x1b0 [mt76_sdio 35339a92c6eb7d4bbcc806a1d22f56365565135c]
[ 52.008431] __mt76_worker_fn+0xe8/0x170 [mt76 ef716597d11a77150bc07e3fdd68eeb0f9b56917]
[ 52.008449] kthread+0x148/0x3ac
[ 52.008466] ret_from_fork+0x10/0x30
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix mt7921_queues_acq implementation according to the vendor sdk.
Fixes: 474a9f21e2e20 ("mt76: mt7921: add debugfs support")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use proper xmit queue handler to dump queue stats.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
