Enable mac80211 TDLS support by default. Disable TDLS hw filtering for
mt7615 devices
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Initialize tx_status_data pointer in order to enable Air Time Fairness
for mt7663u chipset
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Since usb code can't access device registers in interrupt context, move
rcu_read_lock/rcu_read_unlock in mt7615_poll_tx routine. Moreover loop
over a local msta list in mt7615_mac_sta_poll since mt7663u driver will
not be able to complete the inner while loop before sta_poll_list list
is refilled by mt7615_mac_add_txs/mt7615_mac_fill_rx
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
If the vif is running in station mode the aid will be passed by mac80211
using bss_conf.aid. Fix aid configuration in mt7615_mcu_wtbl_generic_tlv
Fixes: 04b8e65922f6 ("mt76: add mac80211 driver for MT7615 PCIe-based chipsets")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Current mt7663 offload firmware can support up to 32 wtbl entries
Fixes: f40ac0f3d3c0 ("mt76: mt7615: introduce mt7663e support")
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add return code parsing for the following unified commands:
- MCU_UNI_CMD_DEV_INFO_UPDATE
- MCU_UNI_CMD_BSS_INFO_UPDATE
- MCU_UNI_CMD_STA_REC_UPDATE
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce rx-queues debugfs node in order to dump rx queues status.
This would be useful for mcu fw debugging
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
A switch from one rate index to the next only happens when tx count from
the current slot is greater than MT7615_RATE_RETRY, which is 1 has to be
subtracted from count, instead of added to it.
Signed-off-by: Felix Fietkau <[email protected]>
A switch from one rate index to the next only happens when tx count from
the current slot is greater than MT7615_RATE_RETRY, which is 1 has to be
subtracted from count, instead of added to it.
Signed-off-by: Felix Fietkau <[email protected]>
Sometimes mt7615_mac_set_timing gets called while the slot time is still
configured to 20. Ensure that in this case it always uses the OFDM CFend
rate.
Signed-off-by: Felix Fietkau <[email protected]>
Sometimes mt7615_mac_set_timing gets called while the slot time is still
configured to 20. Ensure that in this case it always uses the OFDM CFend
rate.
Signed-off-by: Felix Fietkau <[email protected]>
In VHT mode we can receive larger MPDUs. Increasing the buffer size reduces
fragmentation here, which should improve performance.
Signed-off-by: Felix Fietkau <[email protected]>
The hardware requirements for A-MPDU density are entirely on the tx side,
not the rx side. Because of that, the IE value should stay at 0 and the
minimum value should instead be enforced in WTBL/TXWI
MT7615 has no restrictions here
Signed-off-by: Felix Fietkau <[email protected]>
remove IEEE80211_HW_PS_NULLFUNC_STACK capability from mt76_phy_init
routine since 802.11 ps is not currently supported by any devices and it
will conflict with mt7663 ps fw support
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
For sta mode mac80211 provides aid in vif->bss_conf.aid.
In order to properly support 802.11 power-save, configure correct aid
to mcu during sta association
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add missing register definitions in order to enable sensitivity tuning
for mt7663 driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce support for mt7663u 802.11ac 2x2:2 chipset to mt7615 driver.
Main difference respect to pcie code base is the usb code needs to
configure wtbl from non-atomic context
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Create mt7615-common module in order to collect shared code between usb
and mmio code. Move the following source files in mt7615-common module:
- main.c
- init.c
- mcu.c
- mac.c
- debugfs.c
- eeprom.c
- trace.c
Create the following source files for mmio only source code and move them
in mt7615e module:
- pci_init.c
- dma.c
- pci_mac.c
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
make mac_work per phy instead of per device and fix a possible deadlock
in mt7615_stop since mt7615_mac_work runs holding mt76 mutex
Fixes: fdd2e570764c2 ("mt76: mt7615: add dual-phy support for mac80211 ops")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Sparse report warnings at mt76_tx_status_unlock() and mt76_tx_status_lock()
warning: context imbalance in mt76_tx_status_lock() - wrong count at exit
warning: context imbalance in mt76_tx_status_unlock() - unexpected unlock
The root cause is the additional __acquire(&dev->status_list.lock)
and __release(&dev->status_list.unlock) called
from inside mt76_tx_status_lock() and mt76_tx_status_unlock().
Remove __acquire(&dev->status_list.lock) annotation
Remove __releases(&dev->status_list.unlock)
Correct &dev->status_list.unlock to &dev->status_list.lock
-unlock not defined in the sk_buff_head struct
Signed-off-by: Jules Irenge <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Enable MSI/MSI-X PCI interrupts by default. This patch has been tested
using Banana Pi r64 board
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix DMA unmap length estimation in mt7615_txp_skb_unmap_hw for mt7622
chipset
Fixes: 6aa4ed7927f1 ("mt76: mt7615: implement DMA support for MT7622")
Signed-off-by: Lorenzo Bianconi <[email protected]>
With MSI interrupts, IRQs must not be enabled from within the IRQ handler,
because that can lead to lost events.
Defer IRQ processing to a tasklet, which is also responsible for enabling
IRQs (to avoid race conditions against the handler)
Co-developed-by: Soul Huang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Avoid having to attempt hw scan and fall back to software for every scan
on devices/firmware without hw scan support
Signed-off-by: Felix Fietkau <[email protected]>
Check that val is not zero before aggr_per estimation in order to avoid a
possible division by 0
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The reference driver does not seem to enable it by default, only under certain
conditions, e.g. when a .bin file is loaded.
Make it opt-in via a device tree property for now, in case it is needed on some
boards.
Signed-off-by: Felix Fietkau <[email protected]>
The reference driver does not seem to enable it by default, only under certain
conditions, e.g. when a .bin file is loaded.
Make it opt-in via a device tree property for now, in case it is needed on some
boards.
Signed-off-by: Felix Fietkau <[email protected]>
When the EEPROM data is read from flash, it can contain tx DPD calibration
data. Add support for sending the data to the firmware.
Signed-off-by: Felix Fietkau <[email protected]>
When the EEPROM data is read from flash, it can contain DC offset calibration
data. Add support for sending the data to the firmware.
Signed-off-by: Felix Fietkau <[email protected]>
The reference driver does not seem to enable it by default, only under certain
conditions, e.g. when a .bin file is loaded.
Make it opt-in via a device tree property for now, in case it is needed on some
boards.
Signed-off-by: Felix Fietkau <[email protected]>
The function “platform_get_irq” can log an error already.
Thus omit a redundant message for the exception handling in the
calling function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mac80211/hostapd runs mt7615_set_channel with the same channel
parameters sending multiple rdd commands overwriting the previous ones.
This behaviour is causing tpt issues on dfs channels.
Fix the issue checking new channel freq/width with the running one.
Fixes: 5dabdf71e94e ("mt76: mt7615: add multiple wiphy support to the dfs support code")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rom patch is shared between Bluetooth and Wifi devices, so correct the
naming to allow two drivers to share the same file.
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce address parameter to mt7615_eeprom_init routine in order to be
reused adding usb support to mt7615 driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Generalize mt7615_rate_desc introducing mt7615_wtbl_desc and
mt7615_key_desc data structures in order to configure the hw wtbl
in a non-atomic context for usb devices
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove key dependency from mt7615_mac_wtbl_update_key and export
mt7615_mac_wtbl_update_key, mt7615_mac_wtbl_update_pk and
mt7615_mac_wtbl_update_cipher in order to reuse them in usb code.
Move mt7615_mac_get_cipher in mac.h
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rely on the mt7622 endpoint definitions for mt7663u
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
