Tri-band chipsets support one band on each a-die, so remove the unused
definition of eeprom band selection.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Pass qid into mt7996_mac_write_txwi() to let the tx descriptor of
non-bufferable MMPDUs be filled with correct hw queue index.
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rework and extract common code of capability init for the preparation of
adding EHT capability.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add helpers to get the maximum wtbl size and interface num based
on hw caps.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
There are variants of mt7996 which are different from eht supported and
wtbl size limit. Get the hw caps with CHIP_CONFIG command.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add support to get EHT rate stats from ethtool.
This is the preliminary patch to add EHT support for mt7996.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Increase wcid size to support up to 1024 station hw entries and
64 bcast/mcast hw entries.
This is the preliminary patch to add EHT support for mt7996.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is the preliminary patch to add EHT support for mt7996.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add helpers to get eht cap and phymode on different bands and vifs.
This is the preliminary patch to add EHT support for mt7996.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add CMD_CBW_320MHZ for setting bandwidth 320 MHz to firmware.
This is the preliminary patch to add EHT support for mt7996.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Extend phy type and phymode bitfields for EHT support.
This is the preliminary patch to add EHT support for mt7996.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use the sts variable when setting vht beamform sts cap.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In newer chipsets, CFEND_RATE setting has been moved to different hw
module.
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When flash mode is enabled, and the eeprom data in the flash is not for
the current chipset, it'll still be checked valid, and the default
eeprom bin won't be loaded.
(e.g., mt7915 NIC inserted with mt7916 eeprom data in the flash.)
Fix this kind of case by adding chip id into consideration in
mt7915_check_eeprom().
Reported-by: Cheng-Ji Li <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce is_mt7996() helper for new chipset.
This is a preliminary patch to support mt7996 driver.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add starec tags which will be used in new chipset.
This is a preliminary patch to add mt7996 chipset support.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add bss info tags which will be used in new chipset.
This is a preliminary patch to add mt7996 chipset support.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add event IDs and related bit fields for unified event support.
This is a preliminary patch to add mt7996 chipset support.
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add more unified command IDs which will be used in new chipset.
This is the preliminary patch for mt7996 support.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rename nrow_bw160 and ncol_bw160 since channel width 320 MHz will share
the same field.
This is a preliminary patch to add mt7996 chipset support.
Signed-off-by: MeiChia Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
For connac3 generation, max_ampdu_len should be filled in
struct sta_rec_phy.
This is a preliminary patch to add mt7996 chipset support.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rework some macros for connac3 unified command.
This is a preliminary patch to add mt7996 chipset support.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
For MT7915D, correct antenna index should be set to let DFS radar
detection work on the 5 GHz band.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In previous, we only allow user to configure tx antenna mask
contiguously (e.g. 0x3, 0xf).
This patch allows user to configure tx antenna mask interleavingly
(e.g. 0x5, 0x8). By setting proper antenna mask and nss, user can
prioritized the signal of different antennas, which helps to test
their performance in normal mode.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add mt76_connac_spe_idx() for antenna mask to spatial extension
index conversion. This is used to support flexible control of
tx antenna.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Let the configuration of testmode antenna mask on both band0 and band1
become antenna_mask rather than chainmask. This could simplify the
settings for user and get rid of the conversion when sending fw command.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rework tx paths and streams init part to improve readability, and make
sure that the available tx streams should be smaller than or equal to
the available tx paths.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Compared to fixed payload packets, random payload packets have better
measured EVM under the same txpower. Our tests show EVM becomes at least
2-3 dB better in test cases with high rate and long tx length, which also
aligns the testing results to proprietary driver.
Suggested-by: Jm Chen <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Set EXTRA_INFO_NEW for the first time only to prevent adding the same
starec entry, otherwise the entry might be removed in fw.
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix the issue that the measured inter packet gap didn't fit its
setting value.
Fixes: c2d3b1926f30 ("mt76: mt7915: add support for ipg in testmode")
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add RF registers read/write support for debugging RF issues, which
should be processed by mcu commands.
The index of rf registers use the generic regidx, and are combined
with two parts: WF selection [31:28] and offset [27:0].
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Some of beamforming mib counters are moved to different offsets
or registers in newer chipsets.
Fixes: 99ad32a4ca3a ("mt76: mt7915: add support for MT7986")
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
A-die 7976 has different offset and uses different channel group
definition on txpower init values.
Fixes: 99ad32a4ca3a ("mt76: mt7915: add support for MT7986")
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: MeiChia Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
bssinfo/starec disabled commands are sent during removing interface.
However, if we don't set corresponding enabled commands before
removing interface, the fw may enter an exception state due to
some NULL structs.
For example, the following commands can cause fw timeout in our newer
chips:
ifconfig wlan0/mon0 up
ifconfig wlan0/mon0 down
Fix this by setting enabled commands once interface added.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Set 6GHz cap to iftype data which is matched to the type of
current interface.
Fixes: 50ac15a511e3 ("mt76: mt7921: add 6GHz support")
Signed-off-by: Shayne Chen <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The mask variable is assigned but not used after testmode disabled:
if (!en)
mask = phy->mt76->chainmask;
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add support to set SA/DA/BSSID in testmode.
During mass production stage, some test scripts or test equipments need
to set fixed addresses to detect or parse if a test is passed.
Also, MAC setting is necessary for some tx/rx tests with rx filter,
to make sure rx site only receives expected packets.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Load the default eeprom data when the content of flash/efuse is invalid.
This could help to eliminate some issues due to incorrect or
insufficient rf values.
Co-developed-by: Bo Jiao <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix the issue that some registers not configured properly after
restarting testmode.
(e.g. change state from idle to off, and off to idle)
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add debugfs knobs to read MCU utilization, which helps user know
firmware status more easily to narrow down CPU bottleneck issues.
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Update max rx len of some hw modules, which aligns out vendor SDK.
In normal modes, we exchange MPDU 7991 cap with peers; however, this
won't play a part in sniffer mode.
To prevent packets which exceed the max MPDU size from entering specific
rx path in hw, we need to set a proper limit to filter them out.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix missing HE phy cap related to vif and starec setting.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Re-order and modify conditions for MU DL/UL and ofdma DL fields, and
also clean up some unnecessary zero settings.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Enable HE UL MU-MIMO in sta_rec_muru, which works on both ap and station
mode.
For sending trigger frames, one of the conditions fw uses is to check if
mib rx airtime meets the threshold.
There's a main control of mib rx airtime report register in fw, so we
need to enable the register by mcu cmd instead of directly writing it,
otherwise it will still be disabled by fw.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The VTA (Valid for Txd Arrival time) bit should be set in tx descriptor,
which is necessary for WM fw to schedule SPL (station priority list)
normally before generating txcmd.
If it's not set, some unexpected wcids may be involved in SPL.
Suggested-by: Nelson Chang <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
For broadcast/multicast wcid, the muar_idx should be 0xe.
Fixes: e57b7901469f ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rework starec tags to the order which firmware expected. This also fixes
some weird behaviors during generating SPL of HE-MU.
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix tag len error for sta_rec_wtbl, which causes fw parsing error for
the tags placed behind it.
Fixes: e57b7901469f ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The bit fields of tx rate idx should be 6 bits, otherwise it might be
incorrect in HT mode.
For VHT/HE rates, only 4 bits are actually used by rate idx, the other
2 bits are used for other functions.
Fixes: c31d94af1843 ("mt76: mt7915: fix tx rate related fields in tx descriptor")
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Switch proper tx arbiter mode during testmode tx to prevent from
entering the flow of normal tx in FW.
Also, testmode SU and MU tx need to use different arbiter mode.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
If total eeprom size is divisible by per-page size, the i in for loop
will exceed max page index, which happens in our newer chipset.
Fixes: 26f18380e6ca ("mt76: mt7915: add support for flash mode")
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
If total eeprom size is divisible by per-page size, the i in for loop
will exceed max page index, which happens in our newer chipset.
Fixes: 26f18380e6ca ("mt76: mt7915: add support for flash mode")
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
FCS error packets are filtered by default and won't be reported to
driver, so that RX fcs error and PER in testmode always show zero.
Fix this issue by reading fcs error count from hw counter.
We did't fix this issue by disabling fcs error rx filter since it may
let HW suffer some SER errors.
Fixes: 5d8a83f09941 ("mt76: mt7915: implement testmode rx support")
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move chip-specific stats dumping part before common stats dumping
to provide flexibility for per-chip driver to modify the value of
common stats.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
If efuse mode is used, read all values from fw during eeprom init,
which makes it more convinient to check if rf values in efuse are
properly burned.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Get per-rate txpower with mcu command. This is the preparation of
co-driver for the next chipset, which has different tmac power registers
but can share this same command.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Do not read rf value from efuse when driver is configured to
use flash mode.
Tested-by: Bruce Chuang <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Since driver no longer handler per-rate tx power setting, we need to
read the power values directly from registers.
Tested-by: Evelyn Tsai <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Clean up the flow of per-rate txpower limit setting to get rid of
duplicate work since it has already been handled by firmware, and set
proper max_power based on different channels and regdomains.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix ofdm rate index and ldpc setting in rate setting field of tx
descriptor.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rework mt7915_tm_set_tx_len() with mt76_testmode_alloc_skb() to support
larger packet based on a longer tx_time.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add support to send larger packet in testmode to meet requirements
of some test cases.
The limit of max packet size is determined based on tx rate mode setting.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When testmode can be enabled, the start() callback would already be
called, causing that txpower sku feature isn't really disabled after
testmode is enabled. This patch fix the issue.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to simplify setting state in mt7915
testmode, for adding the new continuous tx state.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Support to set a special tx state in testmode: continuous tx,
which is used for sending tx without time gap.
Note that continuous tx mode doesn't send real packets, instead, it's
pure phy signal, and the waveform can be observed by instrument.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add a testmode mcu command to clean up hw tx queue before a new
testmode tx starts.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
If tx_time is set, calculate a new packet length based on tx time and
tx rate.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add support to calculate and apply ipg parameters in testmode
for MT7915 NIC.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Split parameter settings and mcu command update in mt7915_mcu_set_tx().
This is for reusing edca update function in testmode ipg setting.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Originally, tx queued limit is set to 1000 to prevent from running out
of tx token. If a new testmode tx is triggered while the previous one
hasn't finished yet, we'll wait a period of time until tx_done equals to
tx_queued. Normally, current queued limit can finish in 10 seconds.
However, if ipg is configured to a larger value, less than 1000 packets
can be done in the default timeout period, which may lead to a crash
when a new testmode tx triggered.
To deal with this, make tx queued limit dynamically adjusted according
to ipg value.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add attributes for setting tx inter-packet gap (ipg), duty cycle, and
transmission time in testmode.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add spatial extension (spe) index as a configurable parameter in testmode.
This is used for specifically configuring TX path, such as different
WF TX priority, number of antennas and spatial streams.
If spe_idx is not set, TX path depends on tx_antenna_mask; otherwise,
both spe_idx and tx_antenna_mask are referenced to decide TX path.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
LDPC should be set when bw is larger than 20MHz to make
testmode tx work normally.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The mcs value of HT mode reported by mt7915_mcu_get_rx_rate()
has already been converted to the expected format.
Tested-by: Yiwei Chung <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move per-chip testmode data to mt7615_phy, to properly support
reg_backup and rx status of each band in testmode.
Signed-off-by: Shayne Chen <[email protected]>
Acked-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move per-chip testmode data to mt7915_phy, to properly support
reg_backup and rx status of each band in testmode.
Signed-off-by: Shayne Chen <[email protected]>
Acked-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move testmode mtd variables to mt76_dev, since they are the same on
each phy.
Signed-off-by: Shayne Chen <[email protected]>
Acked-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add testmode support for DBDC NICs (both MT7615D and MT7915D work).
Testmode data and parameters are moved from per-dev to per-phy
for maintaining the value of each band.
Signed-off-by: Shayne Chen <[email protected]>
Acked-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch for DBDC and ipg config support
in testmode.
The wmm_idx of band1 should be configured by this command to
make band1 Tx work normally. Also, for setting ipg, FW needs a
non-empty bss_info structure to do edca parameters update.
Signed-off-by: Shayne Chen <[email protected]>
Acked-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
