Reset wifi subsystem when MCU is already running.
Fixes firmware download failure after soft reboot on systems where the PCIe
reset could not be performed properly.
Signed-off-by: Ryder Lee <[email protected]>
Co-developed-by: Felix Fietkau <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
For performance reasons, mt7915 supports using 2 PCIE gen1 links on
platforms that don't support gen2.
Add support for using this to move traffic for a second DBDC band onto
a dedicated link
Signed-off-by: Felix Fietkau <[email protected]>
Add support to calculate and apply ipg parameters in testmode
for MT7915 NIC.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7915 dbdc support. If dbdc is available, mt7915 primary phy
will work on 2.4GHz band, while secondary one on 5GHz band.
Co-developed-by: Shayne Chen <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Support testmode tx for MT7915A, including tx streams and HE rate
settings.
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Read per-stream measurements every 100 ms and build a simple moving average.
Tested-by: Shayne Chen <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Avoid firmware falling into spectrum mode since that will set
unexpected PSE/PLE thresholds which lead to Tx hang.
This mode should be cleaned before firmware download stage.
Signed-off-by: Chih-Min Chen <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
On 7615 and newer, DMA completion only triggers unmap, but not free of queued
skbs, since pointers to packets are queued internally.
Because of that, there is no need to process the main data queue immediately
on DMA completion.
To improve performance, mask out the DMA data queue completion interrupt and
process the queue only when we receive a txfree event.
This brings the number of interrupts under load down to a small fraction.
Signed-off-by: Felix Fietkau <[email protected]>
Since driver no longer handler per-rate tx power setting, we need to
read the power values directly from registers.
Tested-by: Evelyn Tsai <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Enable MU-MIMO DL/UL and add relative counters in debugfs.
Currently MU modules read WTBL first to notify BA changes to
other cross modules, so adjust mt7915_mcu_sta_ba() accordingly.
Tested-by: Evelyn Tsai <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add debug counters to track status of beamformer and beamformee.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add support for the MediaTek latest generation IEEE 802.11ax 4x4
device MT7915E, which supports concurrent dual-band operation at
both 5GHz and 2.4GHz.
Note that this patch just add basic part and will add more HE
capabilities support in the further patches.
The driver supports AP, Station, Mesh and monitor mode.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Chih-Min Chen <[email protected]>
Suggested-by: Shihwei Lin <[email protected]>
Tested-by: Evelyn Tsai <[email protected]>
Acked-by: Yiwei Chung <[email protected]>
Acked-by: YF Luo <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Felix Fietkau