Move wiphy interface_modes configuration in mt76_alloc_device and
mt76_alloc_phy in order to be overwritten by hw specific code
since some drivers do not support all operating modes (mt7921
supports sta only in the current codebase)
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
wakeup chip every 250ms may cause huge power consumption
try to update statistic counter only if in active status only,
and it would lead fewer power cost
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Instead of read tx status from mac table, add new mechanisam to hanele
tx done event for data frame, every 250ms
This event indicate the real tx status of this pkt in mac layer and
would help mac80211 correct status more frequently
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Firmware functions (SCS, MU ...) also require read-clear phy counters,
hence firmware prepares a global task to read shared fields out to a
shared pool to avoid concurrency. Switch to event format accordingly.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Get rid of an undefined behaviour in mt76_testmode_alloc_skb routine
allocating skb frames
Fixes: 2601dda8faa76 ("mt76: testmode: add support to send larger packet")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Get rid of unnecessary function calls in mt76_testmode_free_skb routine
since they are already managed by dev_kfree_skb
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Free all pending frames in case of failure in mt76_testmode_alloc_skb
routine
Fixes: 2601dda8faa76 ("mt76: testmode: add support to send larger packet")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Get rid of unnecessary if condition in mt7615_add_interface routine
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Get per-rate txpower with mcu command. This is the preparation of
co-driver for the next chipset, which has different tmac power registers
but can share this same command.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
It's much more accurate than .get_tsf + .set_tsf and switch to use
mt76_rmw to operate tsf registers.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
It's much more accurate than .get_tsf + .set_tsf, and switch to use
mt76_rmw to operate tsf registers.
Tested-by: Xing Song <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This patch fixes a mcu hang during device probe on
Marvell ESPRESSObin after a hot reboot.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Return possible error values in mt7921_mac_init routine
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt7921 is mainly used in CE/IoT market so enable runtime-pm by default
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
OMAC idx have to be same with BSS idx according to firmware usage.
Fixes: e0f9fdda81bd ("mt76: mt7921: add ieee80211_ops")
Reviewed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: YN Chen <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Avoid unnecessary consecutive WiFi resets by dropping reset
request when reset work is working.
Co-developed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Similar to mt7915, switching to use standard hwmon sysfs.
For reading temperature, cat /sys/class/ieee80211/phy*/hwmon*/temp1_input
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Thermal cooling device support is added to control the temperature by
throttling the data transmission for the given duration. Throttling is
done by adjusting Tx period by given percentage of time. The thermal
device allows user to configure duty cycle.
Throttling can be disabled by setting the duty cycle to 0. The cooling
device can be found under /sys/class/thermal/cooling_deviceX/.
Corresponding soft link to this device can be found under phy folder
To set duty cycle as 80%,
echo 80 > /sys/class/ieee80211/phy*/cooling_device/cur_state
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This provides userspace with a unified interface, hwmon sysfs, to monitor
temperature in the hardware and can be adapted to system monitoring tools.
For reading temperature, cat /sys/class/ieee80211/phy*/hwmon*/temp1_input
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
There are firmware or hardware issues, which are currently causing tx hangs
when attempting to use these interfaces
Signed-off-by: Felix Fietkau <[email protected]>
The device tree partition offset needs to be added to the function argument,
instead of overwriting it.
Fixes an issue where wrong EEPROM data was sent to the firmware as
pre-calibration data on MT7915.
Fixes: 495184ac91bb ("mt76: mt7915: add support for applying pre-calibration data")
Signed-off-by: Felix Fietkau <[email protected]>
Hw beacon cmd to the mt7921 firmware doesn't only filter out the beacon,
but also performs its own connection monitoring, including periodic
keep-alives to the AP and probing the AP on beacon loss. Will indicate
the host with the event when the firmware detects the connection is lost.
Fixes: 1d8efc741df8 ("mt76: mt7921: introduce Runtime PM support")
Reviewed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: YN Chen <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
It is possible the RCPI from the certain antenna is an invalid value,
especially packets are receiving while the system is frequently entering
deep sleep mode, so consider calculating RSSI with the reasonable upper
bound to avoid report the wrong value to the mac80211 layer.
Fixes: 163f4d22c118 ("mt76: mt7921: add MAC support")
Reviewed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Update MCU command usage to fix WoW configuration with disconnection
and bitmap pattern and to avoid magic number.
Fixes: ffa1bf97425 ("mt76: mt7921: introduce PM support")
Reviewed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: YN Chen <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add addtional the deep sleep control to runtime-pm knob to
allow us to control driver switching between the full power
mode and the deep sleep mode the firmware is able to support.
Reviewed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Enable the deep sleep mode with that firmware is able to trap into
the doze state at runtime to reduce the power consumption further.
The deep sleep mode is not allowed in the STA state transition with
the firmware to have the fast connection experience as we've done in
the full power mode
Reviewed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
If the device is MMIO-based, we must ensure all TxD/TxP on the host
memory all being consumed by the device prior to safely switching to
fw_own state.
Fixes: ec7bd7b4a9c0 ("mt76: connac: check wake refcount in mcu_fw_pmctrl")
Reviewed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
WiFi subsytem reset should control MT_WFSYS_SW_RST_B and then poll the
same register until the bit WFSYS_SW_INIT_DONE bit is set.
Fixes: 0c1ce9884607 ("mt76: mt7921: add wifi reset support")
Reviewed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
As already done for mt7615 and mt7915, enable rx header translation
offload for mt7663 in order to reduce cpu load in the rx path.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
As already done for mt7915 and mt7921, free registered irq line if
mt7615_mmio_probe routine fails
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
BIT(0) in MT_EE_NIC_CONF_1 is use to notify the driver if the radio RF
switch is controlled through a gpio. Use dev_debug instead of dev_err
to log this info.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix theoretical NULL pointer dereference in mt7615_tx_prepare_skb and
mt7663_usb_sdio_tx_prepare_skb routines. This issue has been identified
by code analysis.
Fixes: 6aa4ed7927f11 ("mt76: mt7615: implement DMA support for MT7622")
Fixes: 4bb586bc33b98 ("mt76: mt7663u: sync probe sampling with rate configuration")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Even if this is not a real issue since mt76_tx is never run with wcid set
to NULL, fix a theoretical NULL pointer dereference in mt76_tx routine
Fixes: db9f11d3433f7 ("mt76: store wcid tx rate info in one u32 reduce locking")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Mitigate A-MSDU injection attacks (CVE-2020-24588) by detecting if the
destination address of a subframe equals an RFC1042 (i.e., LLC/SNAP)
header, and if so dropping the complete A-MSDU frame. This mitigates
known attacks, although new (unknown) aggregation-based attacks may
remain possible.
This defense works because in A-MSDU aggregation injection attacks, a
normal encrypted Wi-Fi frame is turned into an A-MSDU frame. This means
the first 6 bytes of the first A-MSDU subframe correspond to an RFC1042
header. In other words, the destination MAC address of the first A-MSDU
subframe contains the start of an RFC1042 header during an aggregation
attack. We can detect this and thereby prevent this specific attack.
For details, see Section 7.2 of "Fragment and Forge: Breaking Wi-Fi
Through Frame Aggregation and Fragmentation".
Signed-off-by: Felix Fietkau <[email protected]>
Add runtime configuration for bitrate mask. This update firmware rate
control to add a boundary on top of table to limit the rate selection
for each peer, so when user set bitrates vht-mcs-5 1:9, which actually
means nss = 1 mcs = 0~9. This only applies to data frames as for other
mgmt, mcast, bcast still use legacy rates as it is.
Note that driver does not support GI configuration.
Example:
iw dev wlan0 set bitrates vht-mcs-5 1:9 he-mcs-5 2:7
iw dev wlan0 set bitrates legacy-5 6 he-mcs-5 2:0-11
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove obsoleted codes. This is the preparation for .set_bitrate_mask().
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
"idx" needs to be signed for the error handling to work.
Fixes: 495184ac91bb ("mt76: mt7915: add support for applying pre-calibration data")
Signed-off-by: Dan Carpenter <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
