Get the RX queue inside mt76u_refill_rx. This will allow to reuse
mt76u_urb_alloc for TX allocations.
Signed-off-by: Stanislaw Gruszka <[email protected]>
mt76_queue_entry has alreay one bool variable, adding new one will
not increase it's size. Removing ->done filed from mt76u_buf will
allow to use urb directly in mt76usb code.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Setup usb device private data. This allows to remove mt76u_buf->dev
and simplify some routines as no longer we need to get usb device
through usb interface.
Signed-off-by: Stanislaw Gruszka <[email protected]>
We do not need to pass len and sglen to the function.
Additionally pass gfp to control allocation context.
Signed-off-by: Stanislaw Gruszka <[email protected]>
We can not run mt76u_alloc_buf() concurently, rx_tasklet is stooped
when mt76u_submit_rx_buffers(). We can remove rx_page_lock.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Enable AP mode. For now without multi-vif support, this will require
more testing and investigation.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
All mt76 drivers (now also USB drivers) require empty .set_tim
callback. Add it to common mt76 module and use on all drivers.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Create software MT_TXQ_PSD queue for USB and map it to MT_TXQ_VO
since we do not have USB endpoint for PSD. This should make
mt76_release_buffered_frames() work by sending released frames
via MT_TXQ_VO.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Since we sent PS buffered frames via beacon memory we need to make
beacon slots bigger. That imply we will also need to decrease number
of slots as beacon SRAM memory is limited to 8kB.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Program beacons data and PS buffered frames on TBTT work for USB.
We do not have MT_TXQ_PSD queue available via USB endpoints. The way
we can send PS broadcast frames in timely manner before PS stations go
sleep again is program them in beacon data area. Hardware do not modify
those frames since TXWI is properly configured. mt76x02_mac_set_beacon()
already handle this and free no longer used frames.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is required to sent multicast/broadcast frames in USB AP
mode just after beacon.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add sta_ps callback but dont set WCID drop sicne registers for USB
can not be accessed from tasklet context.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move some TBTT mmio functions to mt76x02_beacon.c and create new ones
in order to be reused by USB pre-TBTT.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add implementation of beacon_ops for USB and exit function to
stop the timer if running when device is removed. Still no
actual work on pre tbtt event.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Enabling/disableing TBTT and beacon will be diffrent for USB. Introduce
beacon_ops to encapsulate that and implement it for MMIO. USB
implementation is noop for now.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add timer and work for pre TBTT for USB devices. For now code
doesn't do anyting useful, just add hrtimer which synchronize
with hardware MT_TBTT_TIMER.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move most of beaconing code into separate file and separate beacon
initialization for USB and MMIO as pre TBTT implementation for USB
will be different.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Now that the sequence number allocation is fixed, we can finally send a BAR
at powersave wakeup time to refresh the receiver side reorder window
Signed-off-by: Felix Fietkau <[email protected]>
If the MT_TXD3_SN_VALID flag is not set in the tx descriptor, the hardware
assigns the sequence number. However, the rest of the code assumes that the
sequence number specified in the 802.11 header gets transmitted.
This was causing issues with the aggregation setup, which worked for the
initial one (where the sequence numbers were still close), but not for
further teardown/re-establishing of sessions.
Additionally, the overwrite of the TID sequence number in WTBL2 was resetting
the hardware assigned sequence numbers, causing them to drift further apart.
Fix this by using the software assigned sequence numbers
Signed-off-by: Felix Fietkau <[email protected]>
mutex->lock must not be held while cancelling workqueues, because it is held
by the workqueue items themselves
Signed-off-by: Felix Fietkau <[email protected]>
Use register definitions instead of magic numbers in mt7603_reg_map
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove mt7603_mcu_init since mcu.mutex has been already initialized
in mt76_mmio_init. Run mt7603_load_firmware directly in
mt7603_init_hardware
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
As already done for mt76_dma_tx_queue_skb_raw, add static qualifier to
mt76_dma_tx_queue_skb and introduce mt76_tx_queue_skb in order to run
mt76_dma_tx_queue_skb in driver code
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
q->tail can be safely updated without locking, because there is no
concurrent access. If called from outside of the tasklet (for flushing),
the tasklet is always disabled.
q->queued can be safely read without locking, as long as the decrement
happens within the locked section.
This patch allows cleaning up tx packets outside of the section that holds
the queue lock for improved performance
Signed-off-by: Felix Fietkau <[email protected]>
Add mt76_tx_info as auxiliary data structure to pass values
to tx_prepare_skb pointer. This is a preliminary patch to add
support for new chipsets (e.g. mt7615)
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move skb dma mapping before configuring txwi since new chipsets (mt7615)
will need skb dma addresses in order to properly configure txwi
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
