The SKB containing the generated beacon is not freed when the beacon
queue is deected stuck and scheduled for recovery.
Fixes potential memory leaks in case the beacon queue is detected stuck.
Signed-off-by: David Bauer <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
When performing a full system recovery of the MCU on a dual-phy
platform, band 0 (usually 2.4GHz) stops reading correct noise floor
data.
This is due to noise floor reporting only being configured correctly
for the second device PHY.
Configure the respective registers correctly after restarting the MCU
firmware to fix reported noise-floor values.
Signed-off-by: David Bauer <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
mt76 tracks the PSM state of a sta internally with a wcid flag. TX to
such clients is skipped based on the presence of this flag.
This flag was not added to the PS state notify handler for MT7915 chips.
Without this flag, mt76 queues pending frames to the hardware,
accounting for airtime when a PSM notification is received while in a TX
iteration.
Set the PS flag for the STA WCID to prevent this from happening. TX gets
skipped in presence of this flag.
Signed-off-by: David Bauer <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Host receives a power save state change event everytime a station enters
or leaves PS mode. Use this unsolicited event to stop filling up TX
queues in firmware, as the hardware will buffer frames for stations in
power safe indefinitely.
Limit packets to be enqueued for sleeping STAs in order to manage the
packet backlog in the host-system while still being able to indicate
pending traffic to said STAs.
Signed-off-by: David Bauer <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
mt76_txq_send_burst does check if the number of non-AQL frames exceeds
the maximum. In this case the queue is returned to ieee80211_return_txq
when iterating over the scheduled TXQs in mt76_txq_schedule_list.
This has the effect of inserting said TXQ at the head of the list. This
means the loop will get the same TXQ again, which will terminate the
scheduling round. TXQs following in the list thus never get scheduled
for transmission.
This can manifest in high latency low throughput or broken connections
for said STAs.
Check if the non-AQL packet count exceeds the limit and not return the
TXQ in this case.
Schedule all TXQs for the STA in case the non-AQL limit can be satisfied
again.
Signed-off-by: David Bauer <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
The shared reset procedure of MT7610 and MT7612 stop all queues before
starting the reset sequence.
They however never restart these like other supported mt76 chips
do in the reconfig_complete call. This leads to TX not continuing
after the reset.
Restart queues in the reconfig_complete callback to restore
functionality after the reset.
Signed-off-by: David Bauer <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Restart the MCU and release the patch semaphore before loading the MCU
patch firmware from the host.
This fixes failures upon error recovery in case the semaphore was
previously taken and never released by the host.
This happens from time to time upon triggering a full-chip error
recovery. Under this circumstance, the hardware restart fails and the
radio is rendered inoperational.
Signed-off-by: David Bauer <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
The default timeout set in mt76_connac2_mcu_fill_message of 20 seconds
leads to excessive stalling in case messages are lost.
Testing showed that a smaller timeout of 5 seconds is sufficient in
normal operation.
Signed-off-by: David Bauer <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Increase the timeout for MCU_EXT_CMD_EFUSE_BUFFER_MODE command.
Regular retries upon hardware-recovery have been observed. Increasing
the timeout slightly remedies this problem.
Signed-off-by: David Bauer <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
When operating two VAP on a MT7610 with encryption (PSK2, SAE, OWE),
only the first one to be created will transmit properly encrypteded
frames.
All subsequently created VAPs will sent out frames with the payload left
unencrypted, breaking multicast traffic (ICMP6 NDP) and potentially
disclosing information to a third party.
Disable GTK offloading and encrypt these frames in software to
circumvent this issue. THis only seems to be necessary on MT7610 chips,
as MT7612 is not affected from our testing.
Signed-off-by: David Bauer <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
