This adds an implementation for the chanctx functions, which can be used
by multi-channel capable drivers. Preparation for adding MLO support.
Signed-off-by: Felix Fietkau <[email protected]>
Preparation for supporting multiple radios on a single wiphy on devices
where firmware does not support actual hardware scanning.
This is also a prerequisite for full MLO support
Co-developed-by: Peter Chiu <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Co-developed-by: Michael-CY Lee <[email protected]>
Signed-off-by: Michael-CY Lee <[email protected]>
Co-developed-by: Shayne Chen <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Reset per-phy mac address slot mask in order to avoid leaking entries.
Fixes: 8a55712d124f ("wifi: mt76: mt7915: enable full system reset support")
Signed-off-by: Felix Fietkau <[email protected]>
It seems that the firmware checks the register used for detecting matching
PCIe links in order to figure out if a secondary PCIe link is enabled.
Write the register again just before starting the firmware on hw reset,
in order to fix an issue that left the second band unusable after restart.
Fixes: 9093cfff72e3 ("mt76: mt7915: add support for using a secondary PCIe link for gen1")
Signed-off-by: Felix Fietkau <[email protected]>
The need to retry a command is really uncommon. Reduce the retries to 1 to
speed up recovery from firmware issues.
Signed-off-by: Felix Fietkau <[email protected]>
The second PCIe link is only used to improve performance on older generation
PCIe devices (e.g. MT7621) where the bus speed of one link is not enough to
saturate both wifi bands under really good conditions.
Unfortunately it seems that resetting the hardware after a firmware error
causes the second band to stop working if the second link is in use.
Disable the link until the issue is properly fixed.
For testing, the link can still be enabled via module parameter.
Fixes: 9093cfff72e3 ("mt76: mt7915: add support for using a secondary PCIe link for gen1")
Signed-off-by: Felix Fietkau <[email protected]>
If mcu_skb_prepare_msg is not implemented, incrementing skb refcount does not
work for mcu message retry. In some cases (e.g. on SDIO), shared skbs can trigger
a BUG_ON, crashing the system.
Fix this by only incrementing refcount if retry is actually supported.
Fixes: 3688c18b65ae ("wifi: mt76: mt7915: retry mcu messages")
Reported-by: Nícolas F. R. A. Prado <[email protected]> #KernelCI
Tested-by: Alper Nebi Yasak <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Do not trigger full restarts when running into timeouts during SER.
Immediately abort MCU commands when firmware requests DMA restart.
Signed-off-by: Felix Fietkau <[email protected]>
- use reconfig_complete to restart mac_work / queues
- reset full wtbl after firmware init
- clear wcid and vif mask to avoid leak
Signed-off-by: Felix Fietkau <[email protected]>
When ieee80211_restart_hw is called, all interfaces and stations are
recreated. This can lead to corruption in the sta poll list, since
existing entries were not removed before their private data is reset.
Signed-off-by: Felix Fietkau <[email protected]>
- initialize and use per-sta wcid entry instead of vif wcid
- set wcid flags for 4addr/offload
- fix 'newly' argument for vif sta entry update
Signed-off-by: Felix Fietkau <[email protected]>
On MT7915, MCU hangs do not trigger watchdog interrupts, so they can only
be detected through MCU message timeouts. Ensure that the hardware gets
restarted when that happens in order to prevent a permanent stuck state.
Signed-off-by: Felix Fietkau <[email protected]>
In some cases MCU messages can get lost. Instead of failing completely,
attempt to recover by re-sending them.
Signed-off-by: Felix Fietkau <[email protected]>
Also report auth/disassoc events, in order to give the driver more control over
handling the station state.
Signed-off-by: Felix Fietkau <[email protected]>
This allows the core code to change the channel. Code deduplication and
preparation for adding scanning code to the core.
Signed-off-by: Felix Fietkau <[email protected]>
Do not assume that the first phy has 2 GHz support.
Check sband->band instead of accessing dev->phy.sband_2g.
Signed-off-by: Felix Fietkau <[email protected]>
Move the qid variable declaration further up
Fixes: b473c0e47f04 ("wifi: mt76: mt7603: fix tx queue of loopback packets")
Signed-off-by: Felix Fietkau <[email protected]>
This is expected by the firmware of older chipsets as well, though it may
not have been as strongly required as on mt799x
Fixes: 098428c400ff ("wifi: mt76: connac: set correct muar_idx for mt799x chipsets")
Signed-off-by: Felix Fietkau <[email protected]>
This flag is needed for the PSE client reset. Fixes watchdog reset issues.
Fixes: c677dda16523 ("wifi: mt76: mt7603: improve watchdog reset reliablity")
Signed-off-by: Felix Fietkau <[email protected]>
Use the correct WMM AC queue instead of the MGMT one to fix potential issues
with aggregation sequence number tracking. Drop non-bufferable packets.
Fixes: fca9615f1a43 ("mt76: mt7603: fix up hardware queue index for PS filtered packets")
Signed-off-by: Felix Fietkau <[email protected]>
When pre-calibration data is missing, do not fail the driver probe.
Instead, just print a warning and fall back to regular calibration.
Signed-off-by: Felix Fietkau <[email protected]>
When queueing packets, only the MT76_RESET flag of the primary PHY
is checked. If the primary PHY is scanning or changing channels, this can
lead to packet loss for tx on the second PHY.
Fix this by passing the phy to the .tx_queue_skb op and using it to check
the correct flag.
Signed-off-by: Felix Fietkau <[email protected]>
Copy cck and ofdm separately in order to avoid __read_overflow2_field
warning.
Fixes: f75e4779d215 ("wifi: mt76: mt7996: add txpower setting support")
Signed-off-by: Felix Fietkau <[email protected]>
Do not clear the interrupt mask register on MT7915, since that prevents
MCU_CMD interrupts from being reported, thus causing timeouts during the
reset sequence. Defer stopping WED until tx/rx processing activity has
stopped.
Signed-off-by: Felix Fietkau <[email protected]>
If WED rx is enabled, rx buffers are added to a buffer pool that can be
filled from multiple page pools. Because buffers freed from rx poll are
not guaranteed to belong to the processed queue's page pool, lockless
caching must not be used in this case.
Cc: [email protected]
Fixes: 2f5c3c77fc9b ("wifi: mt76: switch to page_pool allocator")
Signed-off-by: Felix Fietkau <[email protected]>
On MT76x0, LNA gain should be applied for both external and internal LNA.
On MT76x2, LNA gain should be treated as 0 for external LNA.
Move the LNA type based logic to mt76x2 in order to fix mt76x0.
Fixes: 2daa67588f34 ("mt76x0: unify lna_gain parsing")
Reported-by: Shiji Yang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The error handling code was added in order to allow tx enqueue to fail after
calling .tx_prepare_skb. Since this can no longer happen, the error handling
code is unused.
Signed-off-by: Felix Fietkau <[email protected]>
When drv_tx calls race against local tx scheduling, the queue fill status checks
can potentially race, leading to dma queue entries being overwritten.
Fix this by deferring packets from drv_tx calls to the tx worker, in order to
ensure that all regular queue tx comes from the same context.
Signed-off-by: Felix Fietkau <[email protected]>
Enable receiving other-unicast packets
Disable RX header translation in order to proprerly receive data packets
Signed-off-by: Felix Fietkau <[email protected]>
Before preparing the new beacon, check the queue status, flush out all
previous beacons and buffered multicast packets, then (if necessary)
try to recover more gracefully from a stuck beacon condition by making a
less invasive attempt at getting the MAC un-stuck.
Fixes: c8846e101502 ("mt76: add driver for MT7603E and MT7628/7688")
Signed-off-by: Felix Fietkau <[email protected]>
Only trigger PSE reset if PSE was stuck, otherwise it can cause DMA issues.
Trigger the PSE reset while DMA is fully stopped in order to improve
reliabilty.
Fixes: c8846e101502 ("mt76: add driver for MT7603E and MT7628/7688")
Signed-off-by: Felix Fietkau <[email protected]>
It turns out that the code in mt7603_rx_pse_busy() does not detect actual
hardware hangs, it only checks for busy conditions in PSE.
A reset should only be performed if these conditions are true and if there
is no rx activity as well.
Reset the counter whenever a rx interrupt occurs. In order to also deal with
a fully loaded CPU that leaves interrupts disabled with continuous NAPI
polling, also check for pending rx interrupts in the function itself.
Fixes: c8846e101502 ("mt76: add driver for MT7603E and MT7628/7688")
Signed-off-by: Felix Fietkau <[email protected]>
Setting MT_TX_ABORT does not abort any transmission for a wtbl index on its
own. Instead, it modifies the behavior of a queue flush to make it selectively
flush packets for a particular wtbl index.
Adjust powersave filtering to make use of this in order to avoid running into
unnecessary timeouts while flushing
Signed-off-by: Felix Fietkau <[email protected]>
When disabling beacons on a vif, intval is 0. Ensure that dev->mt76.beacon_int
is not overwritten in this case, so that beacons continue to work for other
interfaces.
Signed-off-by: Felix Fietkau <[email protected]>
The IEEE80211_VHT_CAP_EXT_NSS_BW value already indicates support for half-NSS
160 MHz support, so it is wrong to also advertise full 160 MHz support.
Fixes: c2f73eacee3b ("wifi: mt76: mt7915: add back 160MHz channel width support for MT7915")
Signed-off-by: Felix Fietkau <[email protected]>
Capabilities in vif->bss_conf are only initialized in AP mode.
For other modes, they should be enabled by default, in order to avoid a
mismatch.
Fixes: 885f7af7e544 ("wifi: mt76: mt7915: remove mt7915_mcu_beacon_check_caps()")
Signed-off-by: Felix Fietkau <[email protected]>
Felix Fietkau