Since some radar specifications maintained by the driver are incorrect
and are now also maintained by the firmware, offload the initialization
procedure to the firmware.
This fixes issues for radar detection rate testings.
Signed-off-by: StanleyYP Wang <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
After channel switch, some tags of BSSINFO (rfch) and STAREC (bfer,
rate_ctrl) commands should also be updated. Otherwise, a BSS might not be
able to transmit with its peer using correct bandwidth.
Co-developed-by: Shayne Chen <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: StanleyYP Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
RDD_DET_MODE is a firmware command intended for testing and does not
pause TX after radar detection, so remove it from the normal flow;
instead, use the MAC_ENABLE_CTRL firmware command to resume TX after
the radar-triggered channel switch completes.
Fixes: 1529e335f93d ("wifi: mt76: mt7996: rework radar HWRDD idx")
Co-developed-by: Shayne Chen <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: StanleyYP Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Currently, per-radio attributes are set on per-phy basis, i.e., all the
radios present in a wiphy will take attributes values sent from user. But
each radio in a wiphy can get different values from userspace based on
its requirement.
To extend support to set per-radio attributes, add support to get radio
index from userspace. Add an NL attribute - NL80211_ATTR_WIPHY_RADIO_INDEX,
to get user specified radio index for which attributes should be changed.
Pass this to individual drivers, so that the drivers can use this radio
index to change per-radio attributes when necessary. Currently, per-radio
attributes identified are:
NL80211_ATTR_WIPHY_TX_POWER_LEVEL
NL80211_ATTR_WIPHY_ANTENNA_TX
NL80211_ATTR_WIPHY_ANTENNA_RX
NL80211_ATTR_WIPHY_RETRY_SHORT
NL80211_ATTR_WIPHY_RETRY_LONG
NL80211_ATTR_WIPHY_FRAG_THRESHOLD
NL80211_ATTR_WIPHY_RTS_THRESHOLD
NL80211_ATTR_WIPHY_COVERAGE_CLASS
NL80211_ATTR_TXQ_LIMIT
NL80211_ATTR_TXQ_MEMORY_LIMIT
NL80211_ATTR_TXQ_QUANTUM
By default, the radio index is set to -1. This means the attribute should
be treated as a global configuration. If the user has not specified any
index, then the radio index passed to individual drivers would be -1. This
would indicate that the attribute applies to all radios in that wiphy.
Signed-off-by: Roopni Devanathan <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Johannes Berg <[email protected]>
Grab the mt76 mutex running mt7996_mac_sta_rc_work() since it is
required by mt7996_mcu_add_rate_ctrl routine.
Fixes: 28d519d0d493a ("wifi: mt76: Move RCU section in mt7996_mcu_add_rate_ctrl_fixed()")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_abort_scan routine out of mt76_reset_device() in order to
avoid a possible deadlock since mt76_reset_device routine is running
with mt76 mutex help and mt76_abort_scan_complete() can grab mt76 mutex
in some cases.
Fixes: b36d55610215a ("wifi: mt76: abort scan/roc on hw restart")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Tested-by: Ben Greear <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Move mt7996_update_beacons routine inside mt76 mutex critical section
in mt7996_mac_reset_work() in order to run mt7996_vif_conf_link() in
mt7996_mcu_add_beacon routine.
Fixes: f30906c55a400 ("wifi: mt76: mt7996: disable beacons when going offchannel")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Tested-by: Ben Greear <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Grab mt76 mutex in mt7996_mac_sta_event routine in order to rely on
mt76_dereference() utility macro.
Fixes: ecd72f9695e7e ("wifi: mt76: mt7996: Support MLO in mt7996_mac_sta_event()")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Tested-by: Ben Greear <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
This patch fixes the following key issues:
- Pass correct link BSS to mt7996_mcu_add_key(), and use HW beacon
protection mode for mt7990 chipset
- Do not do group key deletion for GTK and IGTK due to FW design, the
delete key command will delete all group keys of a link BSS
- For deleting BIGTK, FW adds a new flow, but the "sec->add" field
should be filled with "SET_KEY". Note that if BIGTK is not deleted, it
will cause beacon decryption issue when switching from an AP interface
to a station interface
Fixes: 0c45d52276fd ("wifi: mt76: mt7996: fix setting beacon protection keys")
Co-developed-by: Allen Ye <[email protected]>
Signed-off-by: Allen Ye <[email protected]>
Co-developed-by: Peter Chiu <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Obtain the correct link ID and, if needed, switch to the corresponding
wcid before populating the TX descriptor and TX payload.
Rules for link id:
- For QoS data of MLD peers (excluding EAPOL), select the primary or
secondary wcid based on whether the TID is odd or even to meet FW/HW
requirements
- For other packets, use IEEE80211_TX_CTRL_MLO_LINK if specified
(such as multicast and broadcast packets)
Signed-off-by: Shayne Chen <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
For an MLD peer, we only need to call the teardown command when removing
the last link, and there's no need to call mt7996_mcu_add_sta() for the
earlier links.
Fixes: c1d6dd5d03eb ("wifi: mt76: mt7996: Add mt7996_mcu_teardown_mld_sta rouine")
Signed-off-by: Shayne Chen <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Fix several fields in mt7996_mcu_bss_basic_tlv() that were not obtained
from the correct link. Without this patch, the MLD station interface
does not function properly.
Fixes: 34a41bfbcb71 ("wifi: mt76: mt7996: prepare mt7996_mcu_add_dev/bss_info for MLO support")
Signed-off-by: Shayne Chen <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Fix the ibf_timeout field for mt7996, mt7992 and mt7990 chipsets. For
the mt7992, this value shall be set as 0xff, while the others shall be
set as 0x18.
Fixes: ad4c9a8a9803 ("wifi: mt76: mt7996: add implicit beamforming support for mt7992")
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Since wiphy->available_antennas_tx now accumulates the chainmask of all
the radios of a wiphy, use phy->orig_antenna_mask to get the original
max nss for comparison.
Fixes: 69d54ce7491d ("wifi: mt76: mt7996: switch to single multi-radio wiphy")
Signed-off-by: StanleyYP Wang <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
The implementation amounts to setting the driver flag
IEEE80211_VIF_SUPPORTS_CQM_RSSI, and then providing
mechanisms for continuously updating enough information
to be able to provide notifications to userspace when
RSSI drops below a certain threshold
Signed-off-by: Jack Kao <[email protected]>
Signed-off-by: Ming Yen Hsieh <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Passing a BSS conf pointer to mt76_connac2_mac_tx_rate_val() currently has
two inconsistencies.
When called from mt76_connac2_mac_write_txwi(), BSS conf is got by
dereferencing a vif pointer. A NULL vif isn't accounted for though the
function itself supposes it to be NULL and tries to handle this case in
previous checks. This looks like a cosmetic change since the drivers
calling the function (namely, mt7915 and mt7921) set WANT_MONITOR_VIF flag
so judging by info->control.vif initialization inside ieee80211_tx_*()
routines it can't actually come as NULL here.
The same holds for the BSS conf pointer handling inside
mt76_connac2_mac_tx_rate_val(). It is dereferenced before being checked
for NULL. The function supposes to handle the case so reorder the check
and dereference of the pointer. Again, this looks like a syntax issue
only.
Found by Linux Verification Center (linuxtesting.org) with SVACE static
analysis tool.
Co-developed-by: Matvey Kovalev <[email protected]>
Signed-off-by: Matvey Kovalev <[email protected]>
Signed-off-by: Fedor Pchelkin <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
This reverts commit 55e95ce469d0c61041bae48b2ebb7fcbf6d1ba7f.
mt792x drivers don't seem to support multi-radio devices yet. At least
they don't mess with `struct wiphy_radio` at the moment.
Packet capturing on monitor interface doesn't work after the blamed patch:
tcpdump -i wls6mon -n -vvv
Revert the NO_VIRTUAL_MONITOR feature for now to resolve the issue.
Found by Linux Verification Center (linuxtesting.org).
Fixes: 55e95ce469d0 ("wifi: mt76: mt792x: improve monitor interface handling")
Signed-off-by: Fedor Pchelkin <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Update functions which copy to and from MMIO to load bytes as Little
Endian, and also support unaligned buffers.
PCI devices almost universally use Little Endian ordering for MMIO
registers, mt76 is no exception. PCI hardware that is designed to work
with Big Endian CPUs often (but not always) "helps" by transparently
byte-swapping MMIO reads and writes on the wire. If this is enabled
then it cannot be turned off for a single write. On hardware which does
not support this, writel() does the swap in software. When we are
transferring arbitrary bytes to MMIO space, we need them to arrive in
the same order they were in memory, so when the hardware swaps them
this is a problem. Rather than care about how our PCI host controller
works, we instead load bytes as Little Endian - so on a Big Endian
machine this will reverse them, then we use writel() which will put
them back in the right order again. This way we do not make it our
business whether the swapping is done in software or hardware.
Furthermore, inspection of the code shows that these functions are
often called with stack-allocated u8 arrays which have no alignment
guarantees so we now use (get|put)_unaligned_le32().
Fixes:
mt76x2e 0000:02:00.0: ROM patch build: 20141115060606a
mt76x2e 0000:02:00.0: Firmware Version: 0.0.00
mt76x2e 0000:02:00.0: Build: 1
mt76x2e 0000:02:00.0: Build Time: 201607111443____
mt76x2e 0000:02:00.0: Firmware failed to start
mt76x2e 0000:02:00.0: probe with driver mt76x2e failed with error -145
Tested on:
SmartFiber XP8421-B (Big Endian MIPS 34Kc)
- MT7612 -> 5g / ap / psk2
- MT7603 -> 2g / sta / psk2
- MT7603 -> 2g / ap / psk2
TpLink Archer v1200v-v2 (Big Endian MIPS 34Kc)
- MT7613 -> 5g / ap / psk2
- MT7603 -> 2g / sta / psk2
Signed-off-by: Caleb James DeLisle <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Introduce Airoha NPU support to MT7996 driver. NPU is used to enable
traffic forward offloading between the MT76 NIC and the Airoha ethernet one
available on the Airoha EN7581 SoC using Netfilter Flowtable APIs.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Add the NPU generic layer in mt76 module. NPU will be used to enable
traffic forward offloading between the MT76 NIC and the Airoha ethernet one
available on the Airoha EN7581 SoC using Netfilter Flowtable APIs.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to enable traffic forward offloading between
the MT76 NIC and the Airoha ethernet one via the Airoha NPU module
available on the Airoha EN7581 SoC.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
The current WED only supports 256 wcid, whereas mt7986 can support up to
512 entries, so firmware provides a rule to get sta_info by DA when wcid
is set to 0x3ff by txd. Also, WED provides a register to overwrite txd
wcid, that is, wcid[9:8] can be overwritten by 0x3 and wcid[7:0] is set
to 0xff by host driver.
However, firmware is unable to get sta_info from DA as DA != RA for
4addr cases, so firmware and wifi host driver both use wcid (256 - 271)
and (768 ~ 783) for sync up to get correct sta_info.
Currently WDS+WED config is completely broken on MT7986/7981 devices if
without this patch.
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Sujuan Chen <[email protected]>
Signed-off-by: Shengyu Qu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The commit 22b980badc0f ("mt76: add functions for parsing rate power limits
from DT") introduced generic support for rates limits in the devicetree.
But the mt7915 supports beamforming and has another table for configuring
the backoff limits. These can be configured in the DT with the paths-*
properties. The path-*-bf are the ones relevant for beamforming and the
ones without -bf suffix for "traditional" path backoff.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Sven Eckelmann (Plasma Cloud) <[email protected]>
Link: https://patch.msgid.link/20251007-backoff-table-support-v3-3-fd6e2684988f@simonwunderlich.de
Signed-off-by: Felix Fietkau <[email protected]>
The power-limits for ru and mcs and stored in the devicetree as bytewise
array (often with sizes which are not a multiple of 4). These arrays have a
prefix which defines for how many modes a line is applied. This prefix is
also only a byte - but the code still tried to fix the endianness of this
byte with a be32 operation. As result, loading was mostly failing or was
sending completely unexpected values to the firmware.
Since the other rates are also stored in the devicetree as bytewise arrays,
just drop the u32 access + be32_to_cpu conversion and directly access them
as bytes arrays.
Cc: [email protected]
Fixes: 22b980badc0f ("mt76: add functions for parsing rate power limits from DT")
Fixes: a9627d992b5e ("mt76: extend DT rate power limits to support 11ax devices")
Signed-off-by: Sven Eckelmann (Plasma Cloud) <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove unnecessary link_id checks in mt7996_tx routine since if the link
identifier provided by mac80211 is unspecified the value will be
overwritten at the beginning on the function.
Fixes: f940c9b7aef6 ("wifi: mt76: mt7996: Set proper link destination address in mt7996_tx()")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
