The muru enable/disable are only set after the first station connection.
Without this patch, the firmware couldn't enable muru
if the first connected station is non-HE type.
Fixes: 16bff457dd33a ("mt76: mt7915: rework mt7915_mcu_sta_muru_tlv()")
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: MeiChia Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
fix warning: variable 'temp' set but not used and
cast from pointer to integer of different size
Fixes: 91eeaef2523f ("mt76: mt7915: add support for MT7986")
Reported-by: kernel test robot <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
fix logic error and remove the unused member 'adie' of mt7915_dev.
Fixes: 91eeaef2523f ("mt76: mt7915: add support for MT7986")
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix the following sparse warning in mt7915_mac_tx_free routine:
warning: incorrect type in assignment (different base types)
expected unsigned int [usertype] *cur_info
got restricted __le32 *
warning: cast to restricted __le32
Fixes: c17780e7b21ec ("mt76: mt7915: add txfree event v3")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix the following sparse warnings:
warning: incorrect type in initializer (different base types)
expected restricted __le16 [usertype] msg_type
got int
warning: incorrect type in assignment (different base types)
expected restricted __le32 [usertype] timestamp
got unsigned int
Fixes: 988845c9361a0 ("mt76: mt7915: add support for passing chip/firmware debug data to user space")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix channel state update error issue due to wrong
register access for mt7916.
Signed-off-by: Sujuan Chen <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Before, the hardware would be allowed to transmit injected 802.11 MPDUs
as A-MSDU. This resulted in corrupted frames being transmitted. Now,
injected MPDUs are transmitted as-is, without A-MSDU.
The fix was verified with frame injection on MT7915 hardware, both with
and without the injected frame being encrypted.
If the hardware cannot do A-MSDU aggregation on MPDUs, this problem
would also be present in the TX path where mac80211 does the 802.11
encapsulation. However, I have not observed any such problem when
disabling IEEE80211_HW_SUPPORTS_TX_ENCAP_OFFLOAD to force that mode.
Therefore this fix is isolated to injected frames only.
The same A-MSDU logic is also present in the mt7921 driver, so it is
likely that this fix should be applied there too. I do not have access
to mt7921 hardware so I have not been able to test that.
Signed-off-by: Johan Almbladh <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Instead of just taking the maximum per-chain signal strength values,
add an approximation for the sum of the combined signal.
This should more accurately reflect the real signal strength, especially
if the per-chain signal strength values are close to each other
Signed-off-by: Felix Fietkau <[email protected]>
Do not always copy ethernet header in mt{7615,7915,7921}_reverse_frag0_hdr_trans
and use a pointer instead.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Client mode on DFS channels was broken, because the old code was activating
the DFS detector on radar channels while leaving it in CAC state.
This was caused by making the decision based on the channel radar flag,
instead of hw->conf.radar_enabled.
In order to properly deal with the various corner cases, rip out the state
handling code and replace it with something that's much easier to reason
about.
Signed-off-by: Felix Fietkau <[email protected]>
without this change, the fixed MCS only supports 1 Nss.
Fixes: 70fd1333cd32f ("mt76: mt7915: rework .set_bitrate_mask() to support more options")
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: MeiChia Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The maximum max_mpdu_size of mt7915 is 7991, whereas mt7916 can
support 11454.
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Should use peer's bandwidth instead of chandef->width to
get correct mcs_map.
Fixes: 76be6c076c077 ("mt76: mt7915: add .set_bitrate_mask() callback")
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Free allocated skb in mt7915_mcu_add_sta routine in case of failures.
Fixes: 89bbd3730f382 ("mt76: mt7915: rework starec TLV tags")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The radar detctor is used for dfs channel. So it will start after switching
to dfs channel and will stop after leaving. The TX will be blocked if radar
detctor isn't stopped in non-dfs channel.
This patch resets the dfs state to indicate the radar detector needs to be
stopped.
Signed-off-by: Xing Song <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add missing DATA4_TB_SPTL_REUSE1 he radiotap flag to
mt7915_mac_decode_he_radiotap routine.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt76_connac_lmac_mapping is shared between mt7921 and mt7915
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce rdd_monitor debugfs node in order to dump rdd2 configuration.
Tested-by: Owen Peng <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7915_mcu_rdd_background_enable and
mt7915_mcu_background_chain_ctrl routines to configure rx dfs dedicated chain.
This is a preliminary patch to add zero-wait dfs support performing CAC
detection on rdd2.
Tested-by: Owen Peng <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
bssinfo/starec disabled commands are sent during removing interface.
However, if we don't set corresponding enabled commands before
removing interface, the fw may enter an exception state due to
some NULL structs.
For example, the following commands can cause fw timeout in our newer
chips:
ifconfig wlan0/mon0 up
ifconfig wlan0/mon0 down
Fix this by setting enabled commands once interface added.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The mcs value of HT mode reported by mt7915_mac_add_txs_skb()
has already been converted to the expected format.
Fixes: 9908d98ae72cd ("mt76: mt7915: report tx rate directly from tx status")
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This can be used to assist in debugging driver or firmware tx/rx issues.
The data is streamed to user space using a relay file in debugfs
Signed-off-by: Felix Fietkau <[email protected]>
In some cases, the WA firmware needs to know if encryption is used, in order
to set the protection bit of packets
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_connac_mcu_rdd_cmd routine in mt76-connac module and remove
duplicated code.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rely on mt76_connac_mcu_set_rts_thresh routine in mt7915 driver and
remove duplicated code.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_connac_mcu_gen_dl_mode utility routine in mt76_connac_mcu.h
since it is shared by all drivers.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rely on mt76_connac_mcu_init_download routine in mt7915 driver and
remove duplicated code.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rely on mt76_connac_mcu_patch_sem_ctrl/mt76_connac_mcu_start_patch
routine in mt7915 driver and remove duplicated code.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_connac_mcu_restart routine in mt76-connac since it is shared
between mt7921 and mt7915.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rely on mt76_connac_mcu_start_firmware and remove duplicated code.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_connac_mcu_set_pm utility routine in connac module since it is
shared between mt7615 and mt7915 drivers.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_connac_mcu_wtbl_update_hdr_trans routine in mt76-connac module
since it is shared between mt7915 and mt7615 drivers.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rely on mt76_connac_mcu_wtbl_hdr_trans_tlv routine and
remove duplicated code.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rely on mt76_connac_mcu_wtbl_ht_tlv routine and
remove duplicated code.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rely on mt76_connac_mcu_wtbl_smps_tlv routine in mt7915
and remove duplicated code.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rely on mt76_connac_mcu_sta_uapsd routine in mt7915 and remove
duplicated code.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rely on mt76_connac_mcu_sta_basic_tlv routine in mt7915 and remove
duplicated code.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rely on mt76_connac_mcu_wtbl_generic_tlv routine in mt7915 and remove
duplicated code.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rely on mt76_connac_mcu_sta_ba routine in mt7915 and remove duplicated
code.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rely on mt76_connac_mcu_wtbl_ba_tlv routine in mt7915 and remove
duplicated code.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
