Run mt76_free_device instead of ieee80211_free_hw if device probing
fails in order to remove the already allocated mt76 workqueue
Fixes: a86f1d01f5ce5 ("mt76: move mt76 workqueue in common code")
Fixes: f1d962369d568 ("mt76: mt7915: implement HE per-rate tx power support")
Signed-off-by: Lorenzo Bianconi <[email protected]>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <[email protected]>
Signed-off-by: Allen Pais <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
If THIS_MODULE is not set, the module would be removed while debugfs is
being used.
It eventually makes kernel panic.
Fixes: e57b7901469f ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Signed-off-by: Taehee Yoo <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
If THIS_MODULE is not set, the module would be removed while debugfs is
being used.
It eventually makes kernel panic.
Fixes: ec9742a8f38e ("mt76: mt7915: add .sta_add_debugfs support")
Signed-off-by: Taehee Yoo <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
sched quota is now updated in mt7663s_txrx_worker so there is no more
need of sched.lock mutex
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Properly account current consumed ple quota in mt7663s_tx_pick_quota
routine and avoid possible underflow.
Fixes: 6ef2d665f64d ("mt76: mt7663s: split mt7663s_tx_update_sched in mt7663s_tx_{pick,update}_quota")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Get rid of mt7663s_sta_add routine and rely on mt7615_mac_sta_add
since sched quota is already initialized in mt7663s_mcu_init_sched
routine
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add sched_quota debugfs node for mt7663s. Scheduling quota stats
are useful for debugging
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In order to reduce cpu cycles, enable hw beacon filter by default if
the device is running offload fw with sta only interfaces.
Disable runtime pm for multi-vif scenario.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
It was accidentally dropped while adding multiple wiphy support
Fixes fast-rx support and avoids handling reordering in both mac80211
and the driver
Cc: [email protected]
Fixes: c89d36254155 ("mt76: add function for allocating an extra wiphy")
Signed-off-by: Felix Fietkau <[email protected]>
When per-packet rate reporting is enabled, the hardware can get stuck under
some conditions. It self-recovers quickly, but in practice this leads to
reduced performance.
In order to avoid running into this issue, disable per-packet rate reporting
by default and query the rx rate from firmware instead, unless monitor mode
is enabled.
Signed-off-by: Felix Fietkau <[email protected]>
Can be used by the caller to get the response data directly instead of using the
hack of storing the result in internal data structures from .mcu_parse_response
Signed-off-by: Felix Fietkau <[email protected]>
The firmware/hardware supports only 16 entries. Trying to use more can lead
to timeouts on some firmware versions
Signed-off-by: Felix Fietkau <[email protected]>
In order to improve driver throughput, convert status_work and net_work
to mt76 worker APIs.
Remove txrx_wq sdio workqueue since it is no longer used
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In order to reduce sdio bus contention, disable interrupts during
txrx_worker processing
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In order to improve driver throughput, convert txrx_work to mt76 worker
threads APIs.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt7663 tx and rx processing in the same workqueue in order to
reduce jitter that can hit tcp performances. This is a preliminary patch
to switch to mt76 workers APIs
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt7615_load_patch in mt7615/mcu.c sometimes fails with:
mt7622-wmac 18000000.wmac: Failed to get patch semaphore
and returns -EAGAIN. But this error is returned all the way up to
mt7615_init_work with no actual retrial performed, leaving a
broken wireless phy.
Wait a bit and retry for up to 10 times before giving up.
Signed-off-by: Chuanhong Guo <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Read per-stream measurements every 100 ms and build a simple moving average.
Tested-by: Shayne Chen <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In the MT7915 info, the fields for the WLAN index / queue overlap with the
token id, and the MT_TX_FREE_PAIR bit indicates, which one is present.
If MT_TX_FREE_PAIR is set, skip processing the token index, since the data
will not be valid.
This fixes accidentally freeing tokens which are still in use by the
hardware with a wrong station pointer.
Signed-off-by: Felix Fietkau <[email protected]>
When looking for a MAC address slot, start by using main BSSID slots 1-3,
afterwards use 16 repeater mode BSSID slots, then start using the slots
usually used for AP mode.
This search order should prevent unnecessary conflicts with AP mode interfaces
on the same PHY
Signed-off-by: Felix Fietkau <[email protected]>
The newer chipsets can deal with the same STA on multiple interfaces
Preparation for supporting more station interfaces
Signed-off-by: Felix Fietkau <[email protected]>
This is primarily for testing and can be used in combination with monitor
mode to make the card respond to packets sent to a specific MAC address.
For now this is only exposed as a debug/testing feature, later on the
approach might be used to support more concurrent station interfaces
Signed-off-by: Felix Fietkau <[email protected]>
Remove A-MSDU max_tx_fragments constraint for sdio since the check is
already performed in mt7663s_tx_run_queue routine
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Qinglang Miao <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
After fixing mac80211 to allow larger A-MSDUs in some cases, there have been
reports of performance regressions and packet loss with some clients.
It appears that the issue occurs when the hardware is transmitting A-MSDUs
bigger than 8k. Limit the local VHT MPDU size capability to 7991, matching
the value used for MT7915 as well.
Signed-off-by: Felix Fietkau <[email protected]>
Convert cpu_to_le16(le16_to_cpu(E1) + E2) to use le16_add_cpu().
Signed-off-by: Liu Shixin <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fixes variable types in mt76x02_dfs_create_sequence and
mt76x02_dfs_add_event_to_sequence
Signed-off-by: Ye Bin <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Release mcu message memory in case of failure in mt7915_mcu_add_beacon
routine
Fixes: e57b7901469fc ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Taking the same approach as initvals_phy.h.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/mediatek/mt76/mt76x0/initvals.h:218:35: warning: ‘mt76x0_dcoc_tab’ defined but not used [-Wunused-const-variable=]
218 | static const struct mt76_reg_pair mt76x0_dcoc_tab[] = {
| ^~~~~~~~~~~~~~~
drivers/net/wireless/mediatek/mt76/mt76x0/initvals.h:86:35: warning: ‘mt76x0_bbp_init_tab’ defined but not used [-Wunused-const-variable=]
86 | static const struct mt76_reg_pair mt76x0_bbp_init_tab[] = {
| ^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/mediatek/mt76/mt76x0/initvals.h:48:35: warning: ‘mt76x0_mac_reg_table’ defined but not used [-Wunused-const-variable=]
48 | static const struct mt76_reg_pair mt76x0_mac_reg_table[] = {
| ^~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/mediatek/mt76/mt76x0/initvals.h:14:35: warning: ‘common_mac_reg_table’ defined but not used [-Wunused-const-variable=]
14 | static const struct mt76_reg_pair common_mac_reg_table[] = {
| ^~~~~~~~~~~~~~~~~~~~
Cc: Felix Fietkau <[email protected]>
Cc: Lorenzo Bianconi <[email protected]>
Cc: Ryder Lee <[email protected]>
Cc: Kalle Valo <[email protected]>
Cc: "David S. Miller" <[email protected]>
Cc: Jakub Kicinski <[email protected]>
Cc: Matthias Brugger <[email protected]>
Cc: Stanislaw Gruszka <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Signed-off-by: Lee Jones <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Unlock dfs channels for mt7615 devices since the driver supports
radar detection. Dfs pattern detector has been tested successfully by
mt7615 users.
Do not unlock DFS frequencies for mt7663 devices since it has not been
tested yet.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
