Instead of stopping and waking only a single queue, handle all phy tx queues
mapped ot the same hardware queue.
Also allow the driver to block tx queues
Signed-off-by: Felix Fietkau <[email protected]>
mt7915 automatically detects dbdc feature so drop debugfs knob.
Move if_comb, mt7915_rates, if_limits structs and mt7915_regd_notifier(),
mt7915_init_wiphy() routines at the begging of init.c in order to make
mt7915_register_ext_phy routine static
Co-developed-by: Shayne Chen <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7915 dbdc support. If dbdc is available, mt7915 primary phy
will work on 2.4GHz band, while secondary one on 5GHz band.
Co-developed-by: Shayne Chen <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to properly support mt7915 dbdc
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce dbdc support to mt7915 devices
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to properly support mt7915 dbdc
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to move properly support mt7915 dbdc
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move hw data queues in mt76_phy from mt76_dev since mt7915 supports per
phy hw queues in dbdc mode
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mcu queue to a dedicated array q_mcu in mt76_dev structure.
This is a preliminary patch to move data queues in mt76_phy and properly
support dbdc
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to move data queues in mt76_phy and properly
support dbdc
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt76_init_mcu_queue utility routine in order to allocate
dedicate q_mcu pointers for mcu hw queues. This is a preliminary patch
to move data queues in mt76_phy and add dbdc support to mt7915 driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rely on mt76_queue instead of qid in tx_queue_skb signature.
This is a preliminary patch to move data queues in mt76_phy and add
dbdc support to mt7915 driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to move data queues in mt76_phy and properly
support dbdc
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to move data queues in mt76_phy and properly
support dbdc for mt7915
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to move data queues in mt76_phy and properly
support dbdc for mt7915
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to move hw data queues in mt76_phy for
mt7915 dbdc support
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_init_tx_queue in mac80211.c since it is shared by all
drivers.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In order to make the code more readable, rely on mt7915_eeprom_field
definitions for eeprom parsing
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Since wtbl workqueue is used only for rate handling, refactor code to
make it more clear
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When looking for a MAC address slot, start by using main BSSID slots 1-3,
afterwards use 16 repeater mode BSSID slots, then start using the slots
usually used for AP mode.
This search order should prevent unnecessary conflicts with AP mode interfaces
on the same PHY.
Note that two PHYs share global 32 omac slots with each other.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt7915_mcu_bss_sync_tlv() is no longer used, so remove it.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The omac_idx variable is u64 so we should use the 64-bit BIT_ULL().
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Make mt7915_eeprom_read routine static since it is used only in eeprom.c
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Support to set tx frequency offset in testmode, which is usally used in
the pre-calibration stage.
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Support tx_power setting in testmode. Note that the tx power value of
antenna 1-3 equal to antenna 0.
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Support testmode rx and display rx statistic by parsing RXV packet
type, which is currently only enabled in testmode.
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Support testmode tx for MT7915A, including tx streams and HE rate
settings.
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Extend enum mt76_testmode_tx_mode to support various HE rate modes.
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]> [update tools/]
Prepare for setting different LTF (1x, 2x, and 4x) and GI (0.8us,
1.6us, 3.2us) combinations in HE rate mode.
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]> [update tools/]
Add the parameter to control STBC function in testmode.
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]> [update tools/]
Support to display snr value when dumping rx statistics.
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]> [update tools/]
Change ib_rssi and wb_rssi into array type, since they could be reported
by per-antenna.
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]> [update tools/]
Since rate configuration is run holding dev mutex, we can run key
configuration in mt7615_set_key for usb/sdio devices avoiding to
schedule the workqueue
Tested-by: Tested-by: YN Chen <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Switch to wep sw crypto for mt7615/mt7915 since wtbl require a sta
reference and wep key is not pairwise
Tested-by: YN Chen <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
SDIO-based WiFi would rely on an additional GPIO pin to wake up the host.
Co-developed-by: YN Chen <[email protected]>
Signed-off-by: YN Chen <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Move mt76_mcu_send_firmware routine in common code since it is actually
shared between mt7615, mt7663, mt7603 and mt7915 devices
Signed-off-by: Lorenzo Bianconi <[email protected]>
Run mt76_free_device instead of ieee80211_free_hw if device probing
fails in order to remove the already allocated mt76 workqueue
Fixes: a86f1d01f5ce5 ("mt76: move mt76 workqueue in common code")
Fixes: f1d962369d568 ("mt76: mt7915: implement HE per-rate tx power support")
Signed-off-by: Lorenzo Bianconi <[email protected]>
