Introduce mt7615_mcu_rdd_send_pattern routine to trigger a radar pattern
detection. Moreover move debugfs related routines in a dedicated source
file.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add Channel Switch Announcement support to mt7615 driver updating beacon
template with CSA IE received from mac80211
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Delay channel calibration after Channel Availability Check. Add some
code cleanup to mt7615_mcu_set_channel
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add hw radar detection support to mt7615 driver in order to
unlock dfs channels on 5GHz band
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7615_regd_notifier callback. This is a preliminary patch to
add radar detection support to mt7615 driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When beacon length is not a multiple of 4, the beacon could be sent with
the last 1-3 bytes corrupted. The skb data is guaranteed to have enough
room for reading beyond the end, because it is always followed by
skb_shared_info, so rounding up is safe.
All other callers of mt76_wr_copy have multiple-of-4 length already.
Cc: [email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Commit f8f527b16db5 ("mt76: usb: use EP max packet aligned buffer sizes
for rx") breaks A-MSDU support. When A-MSDU is enable the device can
receive frames up to q->buf_size but they will be discarded in
mt76u_process_rx_entry since there is no enough room for
skb_shared_info. Fix the issue reallocating the skb and copying in the
linear area the first 128B of the received frames and in the frag_list
the remaining part
Fixes: f8f527b16db5 ("mt76: usb: use EP max packet aligned buffer sizes for rx")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Remove {out,in}_max_packet from mt76_usb data structure since
they just track last usb endpoint and they are not actually used
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move dfs region field in mt76_dev data structure since it is
used by all drivers. This is a preliminary patch to add DFS support to
mt7615 driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Simplify mt7615_set_channel signature removing cfg80211_chan_def
parameter since it is not actually used
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Reduce rx memory footprint allocating just one SG buffer since for the
moment we support just 3839B as maximal size of an A-MSDU.
Introduce different SG_MAX_SIZE definitions for TX and RX sides.
Moreover set q->buf_size to PAGE_SIZE even for SG case.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This makes sure that the driver update peer's bssid when state
transition occurs.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix wrong settings that will drop packets due to hardware's RX table
searching flow.
Fixes: f072c7ba21 ("mt76: mt7615: enable support for mesh")
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix following sparse warnings in mt76x02_usb_core.c
drivers/net/wireless/mediatek/mt76/mt76x02_usb_core.c:29:6: warning:
symbol 'mt76x02u_tx_complete_skb' was not declared. Should it be static?
drivers/net/wireless/mediatek/mt76/mt76x02_usb_core.c:37:5: warning:
symbol 'mt76x02u_skb_dma_info' was not declared. Should it be static?
drivers/net/wireless/mediatek/mt76/mt76x02_usb_core.c:96:52: warning:
restricted __le16 degrades to integer
drivers/net/wireless/mediatek/mt76/mt76x02_usb_core.c:74:5: warning:
symbol 'mt76x02u_tx_prepare_skb' was not declared. Should it be static?
drivers/net/wireless/mediatek/mt76/mt76x02_usb_core.c:244:6: warning:
symbol 'mt76x02u_init_beacon_config' was not declared. Should it be
static?
drivers/net/wireless/mediatek/mt76/mt76x02_usb_core.c:262:6: warning:
symbol 'mt76x02u_exit_beacon_config' was not declared. Should it be
static?
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When TSSI calibration is disabled (which it means the device has been
equipped with an external power amplifier) we need to refer to
different eeprom fields in order to properly configure tx power
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Set per-channel target power as the minimum between the regulatory
tx power and the value configured in the eeprom
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move conn_type configuration directly in mt7615_mcu_set_sta_rec and
remove sta_rec_convert_vif_type since it is actually used just in
mt7615_mcu_set_sta_rec
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When loading EEPROM data from flash, the RF frontend settings need to be
initialized from flash data. Without this, the chip loads the wrong values
from its internal eFuse ROM.
Signed-off-by: Felix Fietkau <[email protected]>
Now that tx status reporting can figure out the first attempted rate, we can
make switching from lower rates to higher rates more conservative.
This reduces retries under bad link conditions and ensures that fallback
rates get more test coverage
Signed-off-by: Felix Fietkau <[email protected]>
Tx status reporting on mt7603 has a number of issues:
- the hardware can alter the first rate index, but it is not reported to
the driver
- probing is very imprecise, because it alters the per-client rate set,
but only considers info->status.rates for rate selection of a single probe
packet
- short/long GI selection has limitations, which are not accurately reported
to mac80211
- if rates are changed while packets are in flight, tx status reports for
the old rate set might be processed based on the new selection
This led to very suboptimal rate selection with minstrel_ht.
This patch completely reworks tx status reporting to get rid of these
limitations:
- Store the previous and current rate set in the driver + the TSF value
at the time of the switch.
- Use the tx status TSF value to determine which rate set needs to be used
as reference.
- Report only short or long GI rates for a single status event, not a mix.
- The hardware reports the last used rate index. Use it along with the
retry count to figure out what rate was used for the first attempt.
- Use the same retry count value for all rate slots to make this calculation
work.
- Derive the probe rate from the current rateset instead of the skb cb
- Do not wait for a status report for the probe frame before removing the
probe rate from the rate table. Do it immediately after it was referenced
in a tx status report.
- Use the first half of the first rate retry budget for the probe rate
in order to avoid using too many retries on that rate
With this patch, throughput under bad link conditions is improved
significantly, and there is a lot less rate fluctuation going on.
Signed-off-by: Felix Fietkau <[email protected]>
This didn't bring the performance benefit that I had hoped for, so the mac80211
patch for this will not make it upstream
Signed-off-by: Felix Fietkau <[email protected]>
Set usb buffer size taking into account skb_shared_info in order to
not always copy the first part of received frames if A-MSDU is enabled
for SG capable devices
Signed-off-by: Lorenzo Bianconi <[email protected]>
Commit f8f527b16db5 ("mt76: usb: use EP max packet aligned buffer sizes
for rx") breaks A-MSDU support. When A-MSDU is enable the device can
receive frames up to q->buf_size but they will be discarded in
mt76u_process_rx_entry since there is no enough room for
skb_shared_info. Fix the issue reallocating the skb and copying in the
linear area the first 128B of the received frames and in the frag_list
the remaining part.
Fixes: f8f527b16db5 ("mt76: usb: use EP max packet aligned buffer sizes for rx")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Do not check key pointer in mt7615_mcu_set_wtbl_key since if set_key_cmd
is SET_KEY, key will be always not NULL. This patch will address a false
positive reported by Coverity-Scan
Addresses-Coverity-ID: 1445463 ("Dereference after null check")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove tim_len in mt7615_mcu_set_bcn since it is not actually used
and ieee80211_beacon_get_tim checks if tim_length is NULL
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix wrong WCID assignment and add RKV (RX Key of this entry is valid)
flag to check if peer uses the same configuration with previous
handshaking.
If the configuration is mismatch, WTBL indicates a “cipher mismatch”
to stop SEC decryption to prevent the packet from damage.
Suggested-by: YF Luo <[email protected]>
Suggested-by: Yiwei Chung <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fixes gcc '-Wunused-but-set-variable' warnings:
drivers/net/wireless/mediatek/mt76/mt7603/mac.c: In function mt7603_fill_txs:
drivers/net/wireless/mediatek/mt76/mt7603/mac.c:969:5: warning: variable pid set but not used [-Wunused-but-set-variable]
drivers/net/wireless/mediatek/mt76/mt7603/mac.c:961:7: warning: variable final_mpdu set but not used [-Wunused-but-set-variable]
drivers/net/wireless/mediatek/mt76/mt7615/mac.c: In function mt7615_fill_txs:
drivers/net/wireless/mediatek/mt76/mt7615/mac.c:555:5: warning: variable pid set but not used [-Wunused-but-set-variable]
drivers/net/wireless/mediatek/mt76/mt7615/mac.c:552:19: warning: variable final_mpdu set but not used [-Wunused-but-set-variable]
They are never used, so can be removed.
Signed-off-by: YueHaibing <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt7603_get_rate in mac80211.c and rename it to mt76_get_rate
since it is shared between mt7603 and mt7615 drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Since all the routines in mt7615_config grub mt76.mutex moves
mutex_lock/mutex_unlock at the beginning/end of mt7615_config
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Initialize get_txpower mac80211 callback to mt76_get_txpower
in order to report the configured tx power to mac80211
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7615_mcu_set_tx_power routine in order to cap tx power
according to the value configured by the user
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Genralize mt76_get_txpower routine for 4x4:4 capable devices
in order to be reused in mt7615 driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Select supported band according to the value read from
eeprom mtd/otp partition
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Calibration data are often available on a specific mtd partition on
embedded devices. Take into account eeprom calibration data if
available.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt7615_insert_ccmp_hdr in mac80211.c and rename it in
mt76_insert_ccmp_hdr since it is shared between mt7603 and mt7615
drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Stop mcu engine and then dma one in mt7615_unregister_device
in order to avoid a mcu hang in mt7615_unregister_device
Signed-off-by: Lorenzo Bianconi <[email protected]>
Use 0600 as edcca file permission in mt76x02 debugfs
Fixes: 643749d4a82b ("mt76: mt76x02: disable ED/CCA by default")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Run mt76x02_edcca_init atomically in mt76_edcca_set since it runs
concurrently with calibration work and mt76x2_set_channel.
Moreover perform phy calibration atomically
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to run mt76x02_edcca_init atomically
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove mt76x02_edcca_init in mt76x2u_set_channel since it is already
run by mt76x2u_phy_channel_calibrate performing channel calibration
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove enable parameter from mt76x02_edcca_init routine signature since
it is always true
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
