mt7915 does not have a per-band number of chains unlike the other chips,
it only has a total number of chains. Yet the current code would
consider the total number as a per-band number.
For example, it would report that a 2x2 + 2x2 DBDC card have 4 chains on
each band and set chainmask to 0b1111 for the first interface and
0b11110000 for the second.
Fixes: 99ad32a4ca3a ("mt76: mt7915: add support for MT7986")
Signed-off-by: Nicolas Cavallari <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
If the nss value is zero in the eeprom, set it to the max.
This eeprom fragment from a mt7915 DBDC shows the problem:
00000190: 24 24 08 00 28 00 00 15 00 00 00 00 00 00 00 00
Fixes: 51a87540232c ("wifi: mt76: mt7915: rework eeprom tx paths and streams init")
Signed-off-by: Nicolas Cavallari <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
For a variant of mt7916, it supports up to 3 tx/rx paths but only 2
spatial streams. This implies that it has one more path to support
beamform. The correct tx/rx path number shall be configured to make sure
beamform works properly.
Fixes: bdaddc92f6b0 ("wifi: mt76: mt7915: deal with special variant of mt7916")
Reviewed-by: Shayne Chen <[email protected]>
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Host triggered and catastrophic event triggered firmware core dumping
for basic firmware issues triage, including state reporting, task/irq
info, function calltrace and MCU memory dump.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Trigger firmware crash and enable full system recovery through debugfs.
This also renames knob "fw_ser" to a clear-cut name "sys_recovery".
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add mt7915_reset() and refactor mt7915_mac_reset_work() to support
full system recovery.
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Reuse mt7915_dma_disable() to reduce duplicated code.
This is a preliminary patch to enable full system reset.
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move aggregation stats array per-phy instead of share it between multiple
interfaces. This is a preliminary patch to add mt7996 driver support.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to move aggr_stats array in mt76_phy
structure.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Similar to mt7915, fix stats clash between bins [4-7] in 802.11 tx
aggregation histogram.
Fixes: 163f4d22c118d ("mt76: mt7921: add MAC support")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This adds selectable RTC/CTS enablement for each interface.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This adds selectable RTC/CTS enablement for each interface.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This reports signal strength of ACK packets from the peer as measured
at each interface.
Tested-by: Shurong Wen <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The MIB INFO command is fetching MIB_BUSY_TIME, MIB_TX_TIME, MIB_RX_TIME and
MIB_OBSS_AIRTIME from the radio and filling out cc_busy, cc_tx, cc_bss_rx
and cc_rx respectively.
busy should be >= tx + rx >= tx + bss_rx but we don’t always quite see this.
Sometimes tx + rx is a bit higher than busy due to inaccurate accounting,
so this patch recalculates numbers to make them more reasonable.
Reported-By: Kevin Schneider <[email protected]>
Tested-by: Kevin Schneider <[email protected]>
Tested-by: Chad Monroe <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Checking the relevant rxd bits for the checksum information only indicates
if the checksum verification was performed by the hardware and doesn't show
actual checksum errors. Checksum errors are indicated in the info field of
the DMA descriptor. Fix packets erroneously marked as CHECKSUM_UNNECESSARY
by checking the extra bits as well.
Those bits are only passed to the driver for MMIO devices at the moment, so
limit checksum offload to those.
Fixes: 2122dfbfd0bd ("mt76: mt7615: add rx checksum offload support")
Fixes: 94244d2ea503 ("mt76: mt7915: add rx checksum offload support")
Fixes: 0e75732764e8 ("mt76: mt7921: enable rx csum offload")
Signed-off-by: Felix Fietkau <[email protected]>
When 802.3 decap offload is enabled, the hardware indicates header translation
failure, whenever either the LLC-SNAP header was not found, or a VLAN header
with an unregcognized tag is present.
In that case, the hardware inserts a 2-byte length fields after the MAC
addresses. For VLAN packets, this tag needs to be removed. However,
for 802.3 LLC packets, the length bytes should be preserved, since there
is no separate ethertype field in the data.
This fixes an issue where the length field was omitted for LLC frames, causing
them to be malformed after hardware decap.
Fixes: 1eeff0b4c1a6 ("mt76: mt7915: fix decap offload corner case with 4-addr VLAN frames")
Reported-by: Chad Monroe <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This reverts commit f17f4864504d754bcbf31e4c89412cdf9946c409.
The reverted commit significantly decreases performance when running
a test where two MT7915 radios have 16 station vdevs each, configured
for AC mode, and transmitting UDP traffic to AP.
Reported-by: Carson Vandegriffe <[email protected]>
Signed-off-by: Ben Greear <[email protected]>
Correct mac timiing settings for different hardware generations.
This improves 40-60Mbps performance.
Fixes: 9aac2969fe5f ("mt76: mt7915: update mac timing settings")
Reported-By: Carson Vandegriffe <[email protected]>
Tested-by: Chad Monroe <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
For MT7915D, correct antenna index should be set to let DFS radar
detection work on the 5 GHz band.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In previous, we only allow user to configure tx antenna mask
contiguously (e.g. 0x3, 0xf).
This patch allows user to configure tx antenna mask interleavingly
(e.g. 0x5, 0x8). By setting proper antenna mask and nss, user can
prioritized the signal of different antennas, which helps to test
their performance in normal mode.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add mt76_connac_spe_idx() for antenna mask to spatial extension
index conversion. This is used to support flexible control of
tx antenna.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Let the configuration of testmode antenna mask on both band0 and band1
become antenna_mask rather than chainmask. This could simplify the
settings for user and get rid of the conversion when sending fw command.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
A variant of mt7916 supports up to 3 tx/rx paths but with only
2 spatial streams. An example usage of the 3rd path is to server as
an auxiliary for beamforming.
In order to deal with this case, this patch reworks some parts to
correctly use paths or streams.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rework tx paths and streams init part to improve readability, and make
sure that the available tx streams should be smaller than or equal to
the available tx paths.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The value of regidx of rf registers is combined with WF selection and
offset. Extend the WF selection field from 4 to 8 bits since the
adie index should also be specified.
Signed-off-by: Evelyn Tsai <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
According to the tx-free-done documentation, the DW4 can be repeated,
so have to be more careful about how we test for walking off the
end of the array.
Signed-off-by: Ben Greear <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
All uses of mt76_wcid_mask_test() have
been removed since commit 8950a62f19c9 ("mt76: get rid of
mt76_wcid_hw routine"), so remove it.
Signed-off-by: Gaosheng Cui <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Group 3 in RxD is disabled in monitor mode. We should use the group 5 in
RxD instead to fix antenna signal way off issue, e.g we would see the
incorrect antenna signal value in wireshark. On the other hand, Group 5
wouldn't be used in STA or AP mode, so the patch shouldn't cause any
harm to those modes.
Fixes: cbaa0a404f8d ("mt76: mt7921: fix up the monitor mode")
Reported-by: Adrian Granados <[email protected]>
Co-developed-by: Deren Wu <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
- remove stbc, because mt76x0 doesn't support it and mt76x2 uses the same
values as HT/VHT
- reduce vht array to 2 elements, because VHT MCS0-7 are the same as HT
Signed-off-by: Felix Fietkau <[email protected]>
In case of PCIe interoperability problem shows up, the firmware
payload may be corrupted in download stage. Turn off L0s to keep
fw download process accurately.
[ 1093.528363] mt7921e 0000:3b:00.0: Message 00000007 (seq 7) timeout
[ 1093.528414] mt7921e 0000:3b:00.0: Failed to start patch
[ 1096.600156] mt7921e 0000:3b:00.0: Message 00000010 (seq 8) timeout
[ 1096.600207] mt7921e 0000:3b:00.0: Failed to release patch semaphore
[ 1097.699031] mt7921e 0000:3b:00.0: Timeout for driver own
[ 1098.758427] mt7921e 0000:3b:00.0: Timeout for driver own
[ 1099.834408] mt7921e 0000:3b:00.0: Timeout for driver own
[ 1100.915264] mt7921e 0000:3b:00.0: Timeout for driver own
[ 1101.990625] mt7921e 0000:3b:00.0: Timeout for driver own
[ 1103.077587] mt7921e 0000:3b:00.0: Timeout for driver own
[ 1104.173258] mt7921e 0000:3b:00.0: Timeout for driver own
[ 1105.248466] mt7921e 0000:3b:00.0: Timeout for driver own
[ 1106.336969] mt7921e 0000:3b:00.0: Timeout for driver own
[ 1106.397542] mt7921e 0000:3b:00.0: hardware init failed
Cc: [email protected]
Fixes: bf3747ae2e25 ("mt76: mt7921: enable aspm by default")
Signed-off-by: Deren Wu <[email protected]>
Tested-by: AngeloGioacchino Del Regno <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Country Location Control (CLC) is an additional control for country rules
in firmware. We introduce this new feature to make sure mt7921 series
working properly in all region.
The addtional policies would be put into firmware based on differnt
regions. mt76 driver should be in charge of submitting per region policy.
Reviewed-by: Sean Wang <[email protected]>
Tested-by: YN Chen <[email protected]>
Co-developed-by: Deren Wu <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
We should reset mstat->airtime_ac along with clear up the entries in the
hardware WLAN table for the Rx and Rx accumulative airtime. Otherwsie, the
value msta->airtime_ac - [tx, rx]_last may be a negative and that is not
the actual airtime the device took in the last run.
Reported-by: YN Chen <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Do not need to check running state before configuring implicit Tx
beamform. It is okay to configure implicit Tx beamform in run time.
Noted that the existing connected stations will be applied for new
configuration only if they reconnected to the interface.
Fixes: 6377b7f330 ("mt76: mt7915: add implicit Tx beamforming support")
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Initialize msta pointer to NULL in mt7921_mac_fill_rx() in order to not
dereference a uninitialized pointer.
Fixes: 0880d40871d1d ("mt76: connac: move mt76_connac2_reverse_frag0_hdr_trans in mt76-connac module")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix the error that mcs will be reduced to a range of 0 to 7 in ht mode.
Fixes: 70fd1333cd32 ("mt76: mt7915: rework .set_bitrate_mask() to support more options")
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
False positive reset would be possibly triggered by those commands we
applied in suspend with HZ MCU timeout, especially it happened when we
enabled kernel log in pm core to diagnose how much time we spend in each
driver during suspend procedure. So we enlarge the value and align the MCU
timeout as other commands we did to reduce the false positive reset.
Signed-off-by: Sean Wang <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Given that there's no data coming from network stack for binding flows,
hence driver counts and reports station's statistics directly through
NL80211_STA_INFO_* based on active PPDU based TxS for offloading data.
Apart from that, WA firmware and its offloading engine (SDO) have hardcoded
"2" as PID, so we introduce MT_PACKET_ID_WED to differentiate WED reporting.
Note that PPDU format TxS is mutually exclusive with MT_TXD5_TX_STATUS_HOST.
Co-developed-by: Yi-Chia Hsieh <[email protected]>
Signed-off-by: Yi-Chia Hsieh <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
