Genralize mt76_get_txpower routine for 4x4:4 capable devices
in order to be reused in mt7615 driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Select supported band according to the value read from
eeprom mtd/otp partition
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Calibration data are often available on a specific mtd partition on
embedded devices. Take into account eeprom calibration data if
available.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt7615_insert_ccmp_hdr in mac80211.c and rename it in
mt76_insert_ccmp_hdr since it is shared between mt7603 and mt7615
drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Stop mcu engine and then dma one in mt7615_unregister_device
in order to avoid a mcu hang in mt7615_unregister_device
Signed-off-by: Lorenzo Bianconi <[email protected]>
Use 0600 as edcca file permission in mt76x02 debugfs
Fixes: 643749d4a82b ("mt76: mt76x02: disable ED/CCA by default")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Run mt76x02_edcca_init atomically in mt76_edcca_set since it runs
concurrently with calibration work and mt76x2_set_channel.
Moreover perform phy calibration atomically
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to run mt76x02_edcca_init atomically
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove mt76x02_edcca_init in mt76x2u_set_channel since it is already
run by mt76x2u_phy_channel_calibrate performing channel calibration
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove enable parameter from mt76x02_edcca_init routine signature since
it is always true
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
To avoid aggregating rate control probing packets with other traffic, and to
ensure that the probing rate gets used, probing packets get assigned a different
internal queueing priority.
This causes packets to be transmitted in a different order, which is compensated
by the receiver side reordering.
However, if A-MPDU is disabled, this reordering can become visible to upper
layers on the receiver side. Disable the priority change if A-MPDU is disabled.
Signed-off-by: Felix Fietkau <[email protected]>
When the hardware falls back to lower rates for a transmit attempt, only the
first status report will show the number of retries correctly. The frames
that follow will report the correct final rate, but number of retries set to 0.
This can cause the rate control module to vastly underestimate the number of
retransmissions per rate.
To fix this, we need to keep track of the initial requested tx rate per packet
and pass it to the status information.
For frames with tx status requested, this is simple: use the rate configured
in info->control.rates[0] as reference.
For no-skb tx status information, we have to encode the requested tx rate in
the packet id (and make it possible to distinguish it from real packet ids).
To do that, reduce the packet id field size by one bit, and use that bit to
indicate packet id vs rate.
This change also improves reporting by filling the status rate array with
rates from first rate to final rate, taking the same steps as the hardware
fallback table. This matters in corner cases like MCS8 on HT, where the
fallback target is MCS0, not MCS7.
Signed-off-by: Felix Fietkau <[email protected]>
When setting chan->max_power after registering the wiphy, chan->max_reg_power
needs to be used as a limit
Signed-off-by: Felix Fietkau <[email protected]>
For the external PA (TSSI OFF) case, the target power needs to be read
from a different location in EEPROM
Signed-off-by: Felix Fietkau <[email protected]>
Introduce a knob in mt7603 debugfs in order to enable/disable
energy detection based on CCA thresholds
Signed-off-by: Lorenzo Bianconi <[email protected]>
Make mt7615_rx_poll_complete static since it is used just in pci.c
to initialize rx_poll_complete function pointer
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Run __mt76_mcu_send_msg instead of __mt7615_mcu_msg_send and remove
duplicated code.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use common function wrapper in mt7615_mcu_exit since the code is shared
with m7603 driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use __mt76_mcu_send_msg wrapper instead of mt7615_mcu_msg_send.
This is a preliminary patch for mt7615-mt7603 mcu code unification
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use mt76 common signature for mt7615_mcu_msg_send. Move skb allocation
in mt7615_mcu_msg_send and remove duplicated code. Remove
__mt7615_mcu_set_wtbl and __mt7615_mcu_set_sta_rec since now are used
just to send mcu msgs. This is a preliminary patch for mt7615-mt7603 mcu
code unification
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove function pointers in mt7615_mcu_set_bss_info and run function
directly. Moreover remove __mt7615_mcu_set_bss_info since it is run just
by mt7615_mcu_set_bss_info and remove duplicated istructions
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Unify mt7615_mcu_set_dev_info and __mt7615_mcu_set_dev_info since the
latter is run just by mt7615_mcu_set_dev_info
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove skb_ret parameter from mt7615_mcu_msg_send signature since it is
actually used just by mt7615_mcu_patch_sem_ctrl. This is a prelimanry
patch to use mt76 common mcu API
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove dest parameter from mt7615_mcu_msg_send/__mt7615_mcu_msg_send
routine signature since it can is always set to MCU_S2D_H2N
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove query parameter from mt7615_mcu_msg_send routine signature since
it can be obtained from cmd value
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use proper mcu message size in mt7615_mcu_add_wtbl and do not
allocate a huge buffer. Moreover use stack memory instead of heap one
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use proper mcu message size in mt7615_mcu_add_wtbl_bmc and do not
allocate a huge buffer. Moreover use stack memory instead of heap one
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove bss_info_convert_vif_type routine since it is run just in
mt7615_mcu_set_bss_info and the switch over vif->type is already there.
Simplify mt7615_mcu_set_bss_info routine
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Do not loop over cmd payload in __mt7615_mcu_set_sta_rec since it is
already done in before running __mt7615_mcu_set_sta_rec (e.g.
mt7615_mcu_set_sta_rec)
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Do not loop over cmd payload in __mt7615_mcu_set_wtbl since it is
already done in before running __mt7615_mcu_set_wtbl (e.g.
mt7615_mcu_set_wtbl_key)
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix sparse warning:
drivers/net/wireless/mediatek/mt76/mt7615/pci.c:37:13:
warning: symbol 'mt7615_irq_handler' was not declared. Should it be static?
Signed-off-by: YueHaibing <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
We dereference "skb" when we assign:
req.pkt_len = cpu_to_le16(MT_TXD_SIZE + skb->len);
^^^^^^^^
So this patch just moves the dev_kfree_skb() down a bit to avoid the
use after free.
Fixes: 04b8e65922f6 ("mt76: add mac80211 driver for MT7615 PCIe-based chipsets")
Signed-off-by: Dan Carpenter <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The problem is that "mvif->omac_idx" is a u8 so it can't be negative
and the error handling won't work. The get_omac_idx() function returns
-1 on error.
Fixes: 04b8e65922f6 ("mt76: add mac80211 driver for MT7615 PCIe-based chipsets")
Signed-off-by: Dan Carpenter <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move netif_napi_del in mt76_dma_cleanup routine since it is done
by all drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This allows tx scheduling and tx cleanup to run concurrently
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This allows tx scheduling and tx cleanup to run concurrently
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move tx_napi in mt76_dev data structure in order to implement
concurrency between tx scheduling and tx cleanup in mt7603 and mt7615
drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Do not allocate mcu requests on the stack in mt7603_mcu_set_eeprom
in order to avoid the following warning:
Warning: the frame size of 1032 bytes is larger than 1024 bytes
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Do not enable/disable pre_tbtt_tasklet tasklet in
mt76x02_sw_scan/mt76x02_sw_scan_complete since it is already done
setting the operating channel. Do run tbtt_tasklet while the device is
offchannel
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Disable pre_tbtt_tasklet tasklet before setting the operating channel.
Enable/disable beacon_timer in mt7603_set_channel
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move pre_tbtt_tasklet tasklet in mt76_dev data structure since
it is used by all drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Announce antenna pattern cap to adapt PHY and baseband settings.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move beacon_mask in mt76_dev data structure since it is used by
all drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
