Allocate skg with enough headroom by mac80211 , this eliminate need
to add extra skb headroom by the mt76x0 driver.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Use common sta_rate_tbl_update on mt76x0 and mt76x2.
mt76x0 do not have support TPC (transmision power control) implmented,
msta->wcid.max_txpwr_adj is only set for mt76x2.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Make common add_interface for mt76x0 and mt76x2e. This change behavior
for mt76x0, but it should work with the new implementation.
mt76x2u has different implementation. Maybe it can use common one,
but for now leave it as is.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Use one conf_tx implementation in mt76x0 and mt76x2. Note this change
conf_tx for mt76x0, but it should work with mt76x2 version.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Use the same AC to hardware queue mappings for all subdrivers.
Note: this change BK and BE mappings for USB drivers.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Use mt76x2_ampdu_action as common function, mt76x0 ampdu_action was
diffrent, but mt76x2 version should work for this driver as well.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Merge mt76x0 and mt76x0 sta add/remove callback. We drop
mt76x0_mac_set_ampdu_factor() for now. Need to consider to add
it to common code, but mt76x2 don't do it so perhaps mt76x0 don't
need it as well.
Signed-off-by: Stanislaw Gruszka <[email protected]>
All current MT devices including new MT7603 type chips support 128
WCIDs, we can unify wcid data in common mt76_dev structure.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Verify if evt field is set to EVT_CMD_DONE in usb mcu
response messages. This is a preliminary patch for usb_mcu layer
unification between mt76x0u and mt76x2u driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Enable the use of CQM_RSSI_LIST with mt76-devices. The change has been
tested with the mt7602, mt7603 and mt7621 PCI wifi-cards. I passed a
list of RSSI thresholds to the driver, and when disconnecting/connecting
the antenna(s) I got an event each time the RSSI went above/below a
threshold.
While I have not been able to test the change with any of the mt76
USB-devices (no access to a device), the RX RSSI management code is
shared between the two device types. Thus, CQM should also work with the
mt76 USB-devices.
Signed-off-by: Kristian Evensen <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Remove the following unused routines for usb buffer
allocation/free/submit:
- mt76x0_usb_alloc_buf
- mt76x0_usb_free_buf
- mt76x0_usb_submit_buf
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Use mt76u_mcu_fw_send_data utility routine for firmware uploading and
remove unused __mt76x0_dma_fw/mt76x0_dma_fw functions
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Use mt76u_mcu_send_msg/__mt76u_mcu_send_msg utility routines to
send commands to usb mcu. Remove following unused routines:
- mt76x0_mcu_wait_resp
- __mt76x0_mcu_msg_send
- mt76x0_mcu_msg_send
- mt76x0_dma_skb_wrap_cmd
- trace_mt_mcu_msg_send_cs
- mt76x0_mcu_cmd_deinit
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Delete core.c source file since, removing mt76x0_wait_asic_ready
routine, it is no longer needed
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Remove mt76x0_vendor_request routine and use
mt76u_vendor_request utility function from mt76-usb
layer in mt76x0_upload_firmware
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Remove mt76x0_complete_urb routine and use mt76u_mcu_complete_urb utility
function as usb mcu completion handler
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Use mt76 usb shared completion data structure in
mt76x0_mcu_wait_resp routine and remove mt76x0
private one
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Remove mt76x0_mcu_msg_alloc duplicated routine and use mt76u_mcu_msg_alloc
utility function for usb mcu message allocation
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Remove mt76x0_vendor_single_wr routine and use mt76u_single_wr
utility function for mcu firmware loading
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Remove mt76x0_vendor_reset duplicated routine and use mt76u_mcu_fw_reset
utility function for mcu fw reset
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Use mt76u_init utility routine for usb initialization.
Moreover remove following unused routines:
- mt76x0_rr
- mt76x0_wr
- mt76x0_rmw
- mt76x0_wr_copy
- mt76x0_assign_pipes
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Introduce multiple regs read support to mcu layer in mt76-usb module.
Multiple regs read will be reused by mt76x0 driver in usb mcu layer
unification between mt76x0 and mt76x2u drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Move mt76x2u_mcu_deinit routine in usb_mcu layer in order to
be reused by mt76x0 driver in usb mcu layer unification between
mt76x0 and mt76x2u drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Split __mt76u_mcu_send_msg and mt76u_mcu_send_msg in order to be reused
by mt76x0 driver in usb mcu layer unification between mt76x0 and
mt76x2u drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Move common definition of mt76_reg_pair in mt76.h
and remove duplicated code in mt76x2_init_common.c
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
