The background radar uses MT_RX_SEL2 as its band indication, so fix it.
Fixes: 7a53eecd5c87 (wifi: mt76: mt7915: check the correctness of event data)
Signed-off-by: StanleyYP Wang <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Enable support for the 5GHz channel 177 with center frequency 5885MHz and
operating class 125 based on IEEE Std 802.11ax-2021 Table E-4.
Signed-off-by: Himanshu Goyal <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The Group ID Management frame is an Action frame of category VHT.
It is transmitted by the AP to assign or change the user position
of a STA for one or more group IDs.
Also, sniffer can use a given group id to monitor STA that belongs
to that group.
Notify underlying driver of changes via BSS_CHANGED_MU_GROUPS.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The Group ID Management frame is an Action frame of category VHT.
It is transmitted by the AP to assign or change the user position
of a STA for one or more group IDs.
Also, sniffer can use a given group id to monitor STA that belongs
to that group.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When header translation failure is indicated, the hardware will insert
an extra 2-byte field containing the data length after the protocol
type field. This happens either when the LLC-SNAP pattern did not match,
or if a VLAN header was detected.
The previous commit accidentally breaks the logic, so reverts back.
Fixes: 27db47ab1f47 (wifi: mt76: mt7996: enable mesh HW amsdu/de-amsdu support)
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt7921_usb_sdio_tx_prepare_skb() calls mt7921_usb_sdio_write_txwi() and
mt7921_skb_add_usb_sdio_hdr(), both of which blindly assume that
adequate headroom will be available in the passed skb. This assumption
typically is satisfied when the skb was allocated in the net core for
transmission via the mt7921 netdev (although even that is only an
optimization and is not strictly guaranteed), but the assumption is
sometimes not satisfied when the skb originated in the receive path of
another netdev and was passed through to the mt7921, such as by the
bridge layer. Blindly prepending bytes to an skb is always wrong.
This commit introduces a call to skb_cow_head() before the call to
mt7921_usb_sdio_write_txwi() in mt7921_usb_sdio_tx_prepare_skb() to
ensure that at least MT_SDIO_TXD_SIZE + MT_SDIO_HDR_SIZE bytes can be
pushed onto the skb.
Without this fix, I can trivially cause kernel panics by bridging an
MT7921AU-based USB 802.11ax interface with an Ethernet interface on an
Intel Atom-based x86 system using its onboard RTL8169 PCI Ethernet
adapter and also on an ARM-based Raspberry Pi 1 using its onboard
SMSC9512 USB Ethernet adapter. Note that the panics do not occur in
every system configuration, as they occur only if the receiving netdev
leaves less headroom in its received skbs than the mt7921 needs for its
SDIO headers.
Here is an example stack trace of this panic on Raspberry Pi OS Lite
2023-02-21 running kernel 6.1.24+ [1]:
skb_panic from skb_push+0x44/0x48
skb_push from mt7921_usb_sdio_tx_prepare_skb+0xd4/0x190 [mt7921_common]
mt7921_usb_sdio_tx_prepare_skb [mt7921_common] from mt76u_tx_queue_skb+0x94/0x1d0 [mt76_usb]
mt76u_tx_queue_skb [mt76_usb] from __mt76_tx_queue_skb+0x4c/0xc8 [mt76]
__mt76_tx_queue_skb [mt76] from mt76_txq_schedule.part.0+0x13c/0x398 [mt76]
mt76_txq_schedule.part.0 [mt76] from mt76_txq_schedule_all+0x24/0x30 [mt76]
mt76_txq_schedule_all [mt76] from mt7921_tx_worker+0x58/0xf4 [mt7921_common]
mt7921_tx_worker [mt7921_common] from __mt76_worker_fn+0x9c/0xec [mt76]
__mt76_worker_fn [mt76] from kthread+0xbc/0xe0
kthread from ret_from_fork+0x14/0x34
After this fix, bridging the mt7921 interface works fine on both of my
previously problematic systems.
[1] https://github.com/raspberrypi/firmware/tree/5c276f55a4b21345cd4d6200a504ee991851ff7a
Link: https://github.com/openwrt/openwrt/issues/11796
Signed-off-by: Matt Whitlock <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Get rid of WEP support in mt76x02_set_key routine since it is not longer
supported upstream.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Issue: Though the Netgear AXE3000 (A8000) is based on the mt7921
chipset because of the unique USB VID:PID combination this device
does not initialize/register. Thus making it not plug and play.
Fix: Adds support for the Netgear AXE3000 (A8000) based on the Mediatek
mt7921au chipset. The method of action is adding the USD VID/PID
pair to the mt7921u_device_table[] array.
Notes: A retail sample of the Netgear AXE3000 (A8000) yeilds the following
from lsusb D 0846:9060 NetGear, Inc. Wireless_Device. This pair
0846:9060 VID:PID has been reported by other users on Github.
Signed-off-by: Reese Russell <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In system warm reboot scene, due to the polling timeout(now 1000us)
is too short to wait dma idle in time, it may make driver probe fail
with error code -ETIMEDOUT. Meanwhile, we also found the dma may take
around 70ms to enter idle state. Change the polling idle timeout to
100ms to avoid the probabilistic probe fail.
Tested pass with 5000 times warm reboot on x86 platform.
[4.477496] pci 0000:01:00.0: attach allowed to drvr mt7921e [internal device]
[4.478306] mt7921e 0000:01:00.0: ASIC revision: 79610010
[4.480063] mt7921e: probe of 0000:01:00.0 failed with error -110
Fixes: 0a1059d0f060 ("mt76: mt7921: move mt7921_dma_reset in dma.c")
Signed-off-by: Quan Zhou <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add support for the MediaTek MT7981 SoC which is similar to the MT7986
but with a newer IP cores and only 2x ARM Cortex-A53 instead of 4x.
Unlike MT7986 the MT7981 can only connect a single wireless frontend,
usually MT7976 is used for DBDC.
Signed-off-by: Alexander Couzens <[email protected]>
Signed-off-by: Daniel Golle <[email protected]>
Just a cosmetic patch to drop redundant prefix for txpower ouput text.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt76 scan command only support 64 channels currently. If the
channel count is larger than 64(for 2+5+6GHz), some channels will
not be scanned. Hence change the scan type to full channel scan
in case of the command cannot include proper list for chip.
Fixes: 399090ef9605 ("mt76: mt76_connac: move hw_scan and sched_scan routine in mt76_connac_mcu module")
Reported-by: Ben Greear <[email protected]>
Tested-by: Isaac Konikoff <[email protected]>
Signed-off-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move some mac shared definitions between mt7996, mt7921 and mt7915 in
mt76_connac2_mac.h.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
eeprom.h is mostly empty for mt7921, so get rid of it.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
gen_ppe_thresh routine is shared between mt7615, mt7915, mt7921 and
mt7996 so move it in mt76_connac module.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
sta_ps callback is just an empty stub for most of the drivers,
so get rid of them.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Most of connac based drivers (mt7921, mt7615, mt7663) share the same
code to enable interrupts. Move it in mt76_connac module.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
irq_tasklet struct is used by most of the drivers (e.g. mt7915, mt7921,
mt7615, mt7663 and mt7996) so move it in common code.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The user is allowed to change beacon tx rate (HT/VHT/HE) from hostapd.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Similar to BSS_CHANGED_BASIC_RATES, this enables mcast rate
configuration through fixed rate tables.
Signed-off-by: Ryder Lee <[email protected]>
Change-Id: Ifc305e8c7de9a7df4ad5f856e2097d721a886aaa
Signed-off-by: Felix Fietkau <[email protected]>
The connac3 removes fixed rate fields to reduce txd size and introduces
global rate tables (64 entries) for rate setting. Driver needs to fill
the corresponding idx in MT_TXD6_TX_RATE while tx, and push mt76_rate
into predifined table at bootup stage so that mvif->basic_rates_idx
can immediately switch out once setting changes.
spe_idx is also needed for fixed rate frames, and will be updated by
future patches.
Note that all table entries are shared across driver and firmware
(i.e.TxBF), hence adding MT7996_BASIC_RATES_TBL to reflect mapping
status.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Take nss calculation into account since this function always wrongly
returns 0.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The vif->bss_conf.mcast_rate should be applied to multicast data frame
only.
Fixes: 182071cdd594 ("mt76: connac: move connac2_mac_write_txwi in mt76_connac module")
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
If the chip reset worker is triggered during the remove process, the chip
DMA may not be properly pushed back to the idle state. This can lead to
corruption of the DMA flow due to the chip reset. Therefore, it is
necessary to stop the chip reset before the DMA is finalized.
To avoid resetting the chip after the reset worker is cancelled, use
__mt7921_mcu_drv_pmctrl() instead of mt7921_mcu_drv_pmctrl(). It is safe to
ignore the pm mutex because the pm worker and wake worker have already been
cancelled.
Fixes: 033ae79b3830 ("mt76: mt7921: refactor init.c to be bus independent")
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Co-developed-by: Deren Wu <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Co-developed-by: Wang Zhao <[email protected]>
Signed-off-by: Wang Zhao <[email protected]>
Signed-off-by: Quan Zhou <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The hardware team has advised the driver that it is necessary to first put
WFDMA into an idle state before resetting the WFDMA. Otherwise, the WFDMA
may enter an unknown state where it cannot be polled with the right state
successfully. To ensure that the DMA can work properly while a stressful
cold reboot test was being made, we have reordered the programming sequence
in the driver based on the hardware team's guidance.
The patch would modify the WFDMA disabling flow from
"DMA reset -> disabling DMASHDL -> disabling WFDMA -> polling and waiting
until DMA idle" to "disabling WFDMA -> polling and waiting for DMA idle ->
disabling DMASHDL -> DMA reset.
Where he polling and waiting until WFDMA is idle is coordinated with the
operation of disabling WFDMA. Even while WFDMA is being disabled, it can
still handle Tx/Rx requests. The additional polling allows sufficient time
for WFDMA to process the last T/Rx request. When the idle state of WFDMA is
reached, it is a reliable indication that DMASHDL is also idle to ensure it
is safe to disable it and perform the DMA reset.
Fixes: 0a1059d0f060 ("mt76: mt7921: move mt7921_dma_reset in dma.c")
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Co-developed-by: Deren Wu <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Co-developed-by: Wang Zhao <[email protected]>
Signed-off-by: Wang Zhao <[email protected]>
Signed-off-by: Quan Zhou <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
`mt7921u_dma_init` can only return zero or negative number according to its
definition. When it returns non-zero number, there exists an error and this
function should handle this error rather than return directly.
Fixes: 0d2afe09fad5 ("mt76: mt7921: add mt7921u driver")
Signed-off-by: Jiefeng Li <[email protected]>
Reviewed-by: Dongliang Mu <[email protected]>
Reviewed-by: Sridhar Samudrala <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mcu_uni_event and mcu_reg_event structs are shared between mt7921 and
mt7615 drivers, so move them in connac lib.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Host triggered and catastrophic event triggered firmware core dumping
for basic firmware issues triage, including state reporting, function
calltrace and MCU memory dump.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add testing points into debugfs to trigger firmware assert and enable
full system recovery. Also rename knob "fw_ser" to a clear-cut name
"sys_recovery".
Co-developed-by: Bo Jiao <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add mt7996_reset() and refactor mt7996_mac_reset_work() to support
full system recovery.
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce p2p-go/p2p-client support to mt7921 driver
CONNECTION_P2P_GC/GO is not supported with the current firmware
so we added mt76_dev to mt76_connac_mcu_sta_basic_tlv signature to
use CONNECTION_INFRA_STA/AP instead for p2p-client and p2p-go
respectively to make it work.
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When the BIOS has been configured for Fast Boot, systems with mt7921e
have non-functional wifi. Turning on Fast boot caused both bus master
enable and memory space enable bits in PCI_COMMAND not to get configured.
The mt7921 driver already sets bus master enable, but explicitly check
and set memory access enable as well to fix this problem.
Tested-by: Anson Tsao <[email protected]>
Signed-off-by: Mario Limonciello <[email protected]>
Acked-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
FIF_* flags from mac80211 is not ABI. mt7921 should not pass it into mcu
directly. Remap FIF_* to driver defined flags as mcu command input.
Fixes: c222f77fd421 ("wifi: mt76: mt7921: fix rx filter incorrect by drv/fw inconsistent")
Signed-off-by: Neil Chen <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
