Add RF registers read/write support for debugging RF issues, which
should be processed by mcu commands.
The index of rf registers use the generic regidx, and are combined
with two parts: WF selection [31:28] and offset [27:0].
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Don't populate the read-only array ppet16_ppet8_ru3_ru0 on the stack but
instead make it static const. Also makes the object code a little smaller.
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Signed-off-by: Colin Ian King <[email protected]>
Don't populate the read-only array ppet16_ppet8_ru3_ru0 on the stack but
instead make it static const. Also makes the object code a little smaller.
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Signed-off-by: Colin Ian King <[email protected]>
To make sure we have the proper antenna config in 6g cap,
move IEEE80211_VHT_CAP_[T/R]X_ANTENNA_PATTERN to stream init.
Fixes: edf9dab8ba27 ("mt76: add 6GHz support")
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fixes potential latency / packet drop issues in cases where a BA session has
not (yet) been established.
Fixes: e195dad14115 ("mt76: add support for 802.3 rx frames")
Signed-off-by: Felix Fietkau <[email protected]>
When the QoS ack policy was set to non explicit / psmp ack, frames are treated
as not being part of a BA session, which causes extra latency on reordering.
Fix this by only bypassing reordering for packets with no-ack policy
Signed-off-by: Felix Fietkau <[email protected]>
Use 0xff (GENMASK(7,0)) in mt7915_init_bitrate_mask routine in order to
initialize bitrate_mask structure in order to avoid truncating value in
memset().
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Report rx mode in mt7915_mac_fill_rx_rate routine in order to properly
add he radiotap if mode is at least HE_SU.
Fixes: 1c9db0aa23fd1 ("mt76: mt7915: update rx rate reporting for mt7916")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix typo in mt7915_muru_debug_set routine and pass muru_debug value to
mt7915_mcu_muru_debug_set() instead of data pointer.
Fixes: 1966a5078f2d2 (mt76: mt7915: add mu-mimo and ofdma debugfs knobs")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix possible NULL pointer dereference in mt7915_mac_fill_rx_vector
routine if the chip does not support dbdc and the hw reports band_idx
set to 1.
Fixes: 78fc30a21cf11 ("mt76: mt7915: move testmode data from dev to phy")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add default case for type switch in mt7986_wmac_gpio_setup routine in
order to avoid a possible uninitialized pointer dereference.
Fixes: 99ad32a4ca3a2 ("mt76: mt7915: add support for MT7986")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In case of error, some resources must be freed, as already done above and
below the devm_kmemdup() and __mt7921e_mcu_drv_pmctrl() calls added in the
commit in Fixes:.
Fixes: 602cc0c9618a ("mt76: mt7921e: fix possible probe failure after reboot")
Signed-off-by: Christophe JAILLET <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
WED support requires using non-coherent DMA, whereas the PCI device might
be configured for coherent DMA.
The WED driver will take care of changing the PCI HIF coherent IO setting
on attach.
Signed-off-by: Felix Fietkau <[email protected]>
Soft reboot might not clear certain condition, so always call
mt7915_wfsys_reset() during init.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Honor runtime-pm user configuration in mt7921_sniffer_interface_iter
routine if we do not have a monitor interface.
Fixes: 1f12fa34e5dc5 ("mt76: mt7921: don't enable beacon filter when IEEE80211_CONF_CHANGE_MONITOR is set")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt7921 is currently using rxfilter defined in mt76_dev for rx filter
configuration. Fix mt7921_configure_filter implementation.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
MT7915_MAX_INTERFACES is per-band declaration in MT7915/MT7986/MT7916.
Enlarge vif_mask to 64 bits wide, including the bit operation.
Reviewed-by: Shayne Chen <[email protected]>
Signed-off-by: Evelyn Tsai <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Clean up and fix error paths in mt7915_register_device
Initialize second DBDC tx queue in mt7915_dma_init
Signed-off-by: Felix Fietkau <[email protected]>
Instead of taking q->lock for every single cleaned up frame, batch up to
16 cleaned up frames before taking it.
Signed-off-by: Felix Fietkau <[email protected]>
dma unmap is already needed for cleanup anyway, so we don't need the extra
tracking and can save a bit of memory here
Signed-off-by: Felix Fietkau <[email protected]>
When setup monitor mode in DFS channel, mt76 send CH_SWITCH_DFS to
fw for channel config. This would cause rx performance bad while
monitoring frames. Settings CH_SWITCH_NORMAL in monitor mode would
get the same performance as normal channels.
Reviewed-by: Shayne Chen <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
IEEE80211_CONF_CHANGE_MONITOR would be set every time even when vif runs as
sta mode.
If vif runs as sta mode, the beacon filter would be falsely enabled
earlier than the associated state.
That is not the behavior the firmware expects and also breaks the original
logic of sta mode. Thus, we only limit the operation to set the beacon
filter only for monitor mode when IEEE80211_CONF_CHANGE_MONITOR is set.
Fixes: 4ad65a54617c ("mt76: mt7921: toggle runtime-pm adding a monitor vif")
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Due to the missing IEEE80211_RADIOTAP_HE_DATA1_BW_RU_ALLOC_KNOWN in
status report, the HE rate in wirehsark/tcpdump always shows wrong value.
Applications will refer to IEEE80211_RADIOTAP_HE_DATA5_DATA_BW_RU_ALLOC
when the flag is set and shows the correct data rate.
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Firmware initialization can take a while. Move mt7921_init_hw routine in
a dedicated work in order to not slow down bootstrap process.
Tested-by: Deren Wu <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce __mt76u_init unitility routine and move mt7615 usb bus ops
into mt7615 module in order to allow specifying driver specific
parameter.
This is a preliminary patch to add usb support to mt7921 driver.
Tested-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to add usb support to mt7921 driver.
Tested-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
