Introduce the second WDMA RX ring in WED driver for MT7988 SoC since the
Mediatek MT7992 WiFi chipset supports two separated WDMA rings.
Add missing MT7988 configurations to properly support WED for MT7992 in
MT76 driver.
Co-developed-by: Rex Lu <[email protected]>
Signed-off-by: Rex Lu <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
Embedding net_device into structures prohibits the usage of flexible
arrays in the net_device structure. For more details, see the discussion
at [1].
Un-embed the net_devices from struct mt76_dev by converting them
into pointers, and allocating them dynamically. Use the leverage
alloc_netdev_dummy() to allocate the net_device object at
mt76_dma_init().
The free of the device occurs at mt76_dma_cleanup().
Link: https://lore.kernel.org/all/[email protected]/ [1]
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: Breno Leitao <[email protected]>
Acked-by: Kalle Valo <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
Since stations are recreated from scratch, all lists that wcids are added
to must be cleared before calling ieee80211_restart_hw.
Set wcid->sta = 0 for each wcid entry in order to ensure that they are
not added again before they are ready.
Signed-off-by: Felix Fietkau <[email protected]>
Several places use rcu_dereference to get a wcid entry without validating
if the index exceeds the array boundary. Fix this by using a helper function,
which handles validation.
Signed-off-by: Felix Fietkau <[email protected]>
Restart the MCU and release the patch semaphore before loading the MCU
patch firmware from the host.
This fixes failures upon error recovery in case the semaphore was
previously taken and never released by the host.
This happens from time to time upon triggering a full-chip error
recovery. Under this circumstance, the hardware restart fails and the
radio is rendered inoperational.
Signed-off-by: David Bauer <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
The default timeout set in mt76_connac2_mcu_fill_message of 20 seconds
leads to excessive stalling in case messages are lost.
Testing showed that a smaller timeout of 5 seconds is sufficient in
normal operation.
Signed-off-by: David Bauer <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Increase the timeout for MCU_EXT_CMD_EFUSE_BUFFER_MODE command.
Regular retries upon hardware-recovery have been observed. Increasing
the timeout slightly remedies this problem.
Signed-off-by: David Bauer <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
One variant of MT7992 has 5 TX paths, so extend the power delta function
to support it. Also, rename nss_delta to path_delta since the value is
based on the number of TX paths rather tha the number of spatial streams.
(path delta [0.5 dBm] = 10 * log(path number) [dBm] * 2)
Co-developed-by: StanleyYP Wang <[email protected]>
Signed-off-by: StanleyYP Wang <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
devm_ioremap() returns NULL on error. Currently, mt7915_mmio_wed_init()
does not check for this case, which results in a NULL pointer
dereference.
Prevent null pointer dereference in mt7915_mmio_wed_init().
Fixes: 4f831d18d12d ("wifi: mt76: mt7915: enable WED RX support")
Signed-off-by: Henry Martin <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
The definition of MT_RX_SEL (for rdd_rx_sel) is mixed with the
definition of HWRDD idx.
For example, MT_RX_SEL2 is for background HWRDD idx, not an option
of rdd_rx_sel.
Therefore, add mt7915_get_rdd_idx as a helper function to get the
HWRDD idx for each variants.
Additionally, remove some parts of the code inherited from the legacy
chips.
For instance,
1. rdd_state is used for single-band-dual-HWRDD chips (for 80+80),
especially the 76xx series.
2. rdd_rx_sel is also used for single-band-dual-HWRDD chips
rx_sel = 0 => RDD0 for WF0, RDD1 for WF2
rx_sel = 1 => RDD0 for WF1, RDD1 for WF3
Chip Variants | 5G rdd idx(=bandidx)| Background rdd idx
-------------------------------|---------------------|-------------------
MT7915A | 0 | 2
MT7915D | 1 | 2
MT7916 2G + 5G (2T2R+1R) | 1 | 2
MT7916 2G + 5G (3T3R) | 1 | N/A
MT7981 2G + 5G | 1 | N/A
MT7986 2G + 5G (one adie DBDC) | 1 | N/A
MT7986 5G (one adie) | 1 (bandidx=MT_BAND1)| N/A
MT7986 2G + 5G (dual adie) | 1 | N/A
Signed-off-by: StanleyYP Wang <[email protected]>
Reviewed-by: Shayne Chen <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Some of the variants do not support background radar, so add a
helper to report background radar capability.
For mt7916, only the variant of 5G 2T2R + 1R supports background
radar.
Signed-off-by: StanleyYP Wang <[email protected]>
Reviewed-by: Shayne Chen <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
mt76 does a lot of:
local_bh_disable();
napi_enable(...napi);
napi_schedule(...napi);
local_bh_enable();
local_bh_disable() is not a real lock, its most likely taken
because napi_schedule() requires that we invoke softirqs at
some point. napi_enable() needs to take a mutex, so move it
from under the BH protection.
Fixes: 413f0271f396 ("net: protect NAPI enablement with netdev_lock()")
Reported-by: Dan Carpenter <[email protected]>
Link: https://lore.kernel.org/[email protected]
Reviewed-by: Eric Dumazet <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
Refactor for making use of mt76_get_power_bound instead of the specific
mt7915_get_power_bound, since we need this for other chipsets as well
when calculating txpower
Signed-off-by: Razvan Grigore <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Assuming sums of values stored in variables such as sub_total_cnt
and total_ppdu_cnt are big enough to warrant their u64 type, it
makes sense to ensure that their calculation takes into account
possible integer overflow issues.
Play it safe and fix the problem by casting right hand expressions
to u64 as well. Also, slightly adjust tabulation.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
Fixes: 1966a5078f2d ("mt76: mt7915: add mu-mimo and ofdma debugfs knobs")
Signed-off-by: Nikita Zhandarovich <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
DIV_ROUND_CLOSEST() after kstrtoul() results in an overflow if a large
number such as 18446744073709551615 is provided by the user.
Fix it by reordering clamp_val() and DIV_ROUND_CLOSEST() operations.
This commit was inspired by commit: 57ee12b6c514.
Fixes: 02ee68b95d81 ("mt76: mt7915: add control knobs for thermal throttling")
Signed-off-by: xueqin Luo <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Fixes linked list management issues during restart, where sta entries
can be recreated and reinitialized while still in the poll list, triggering
kernel warnings.
Signed-off-by: Felix Fietkau <[email protected]>
When a client is roaming to a different AP interface, a duplicate wtbl entry
can be created. This can lead to lost packets or aggregation issues until
the old entry expires.
In order to fix this issue, delete any conflicting entries from WTBL
whenever a station is authorized.
Signed-off-by: Felix Fietkau <[email protected]>
Preparation for supporting multiple radios on a single wiphy on devices
where firmware does not support actual hardware scanning.
This is also a prerequisite for full MLO support
Co-developed-by: Peter Chiu <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Co-developed-by: Michael-CY Lee <[email protected]>
Signed-off-by: Michael-CY Lee <[email protected]>
Co-developed-by: Shayne Chen <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Reset per-phy mac address slot mask in order to avoid leaking entries.
Fixes: 8a55712d124f ("wifi: mt76: mt7915: enable full system reset support")
Signed-off-by: Felix Fietkau <[email protected]>
It seems that the firmware checks the register used for detecting matching
PCIe links in order to figure out if a secondary PCIe link is enabled.
Write the register again just before starting the firmware on hw reset,
in order to fix an issue that left the second band unusable after restart.
Fixes: 9093cfff72e3 ("mt76: mt7915: add support for using a secondary PCIe link for gen1")
Signed-off-by: Felix Fietkau <[email protected]>
Due to a limitation in available memory, the MT7916 firmware can only
handle either 5 GHz or 6 GHz at a time. It does not support runtime
switching without a full restart.
On older firmware, this accidentally worked to some degree due to missing
checks, but couldn't be supported properly, because it left the 6 GHz
channels uncalibrated.
Newer firmware refuses to start on either band if the passed EEPROM
data indicates support for both.
Deal with this limitation by using a module parameter to specify the
preferred band in case both are supported.
Fixes: b4d093e321bd ("mt76: mt7915: add 6 GHz support")
Cc: [email protected]
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The need to retry a command is really uncommon. Reduce the retries to 1 to
speed up recovery from firmware issues.
Signed-off-by: Felix Fietkau <[email protected]>
The second PCIe link is only used to improve performance on older generation
PCIe devices (e.g. MT7621) where the bus speed of one link is not enough to
saturate both wifi bands under really good conditions.
Unfortunately it seems that resetting the hardware after a firmware error
causes the second band to stop working if the second link is in use.
Disable the link until the issue is properly fixed.
For testing, the link can still be enabled via module parameter.
Fixes: 9093cfff72e3 ("mt76: mt7915: add support for using a secondary PCIe link for gen1")
Signed-off-by: Felix Fietkau <[email protected]>
Currently DFS works under assumption there could be only one channel
context in the hardware. Hence, drivers just calls the function
ieee80211_radar_detected() passing the hardware structure. However, with
MLO, this obviously will not work since number of channel contexts will be
more than one and hence drivers would need to pass the channel information
as well on which the radar is detected.
Also, when radar is detected in one of the links, other link's CAC should
not be cancelled.
Hence, in order to support DFS with MLO, do the following changes -
* Add channel context conf pointer as an argument to the function
ieee80211_radar_detected(). During MLO, drivers would have to pass on
which channel context conf radar is detected. Otherwise, drivers could
just pass NULL.
* ieee80211_radar_detected() will iterate over all channel contexts
present and
* if channel context conf is passed, only mark that as radar
detected
* if NULL is passed, then mark all channel contexts as radar
detected
* Then as usual, schedule the radar detected work.
* In the worker, go over all the contexts again and for all such context
which is marked with radar detected, cancel the ongoing CAC by calling
ieee80211_dfs_cac_cancel() and then notify cfg80211 via
cfg80211_radar_event().
* To cancel the CAC, pass the channel context as well where radar is
detected to ieee80211_dfs_cac_cancel(). This ensures that CAC is
canceled only on the links using the provided context, leaving other
links unaffected.
This would also help in scenarios where there is split phy 5 GHz radio,
which is capable of DFS channels in both lower and upper band. In this
case, simultaneous radars can be detected.
Signed-off-by: Aditya Kumar Singh <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Johannes Berg <[email protected]>
commit c4f075582304 ("wifi: mt76: mt7915: fix command timeout in AP stop
period") changes the behavior of mt7915_bss_info_changed() in mesh mode
when enable_beacon becomes false: it calls mt7915_mcu_add_bss_info(...,
false) and mt7915_mcu_add_sta(..., false) while the previous code
didn't. These sends mcu commands that apparently confuse the firmware.
This breaks scanning while in mesh mode on AsiaRF MT7916 DBDC-based cards:
scanning works but no mesh frames get sent afterwards and the firmware
seems to be hosed. It breaks on MT7916 DBDC but not on MT7915 DBDC.
Fixes: c4f075582304 ("wifi: mt76: mt7915: fix command timeout in AP stop period")
Signed-off-by: Nicolas Cavallari <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
-Wflex-array-member-not-at-end was introduced in GCC-14, and we are
getting ready to enable it, globally.
So, in order to avoid ending up with a flexible-array member in the
middle of multiple other structs, we use the `struct_group_tagged()`
helper to create a new tagged `struct mt76_connac2_mcu_rxd_hdr`.
This structure groups together all the members of the flexible
`struct mt76_connac2_mcu_rxd` except the flexible array.
As a result, the array is effectively separated from the rest of the
members without modifying the memory layout of the flexible structure.
We then change the type of the middle struct members currently causing
trouble from `struct mt76_connac2_mcu_rxd` to `struct
mt76_connac2_mcu_rxd_hdr`.
We also want to ensure that when new members need to be added to the
flexible structure, they are always included within the newly created
tagged struct. For this, we use `static_assert()`. This ensures that the
memory layout for both the flexible structure and the new tagged struct
is the same after any changes.
This approach avoids having to implement `struct mt76_connac2_mcu_rxd_hdr`
as a completely separate structure, thus preventing having to maintain
two independent but basically identical structures, closing the door
to potential bugs in the future.
So, with these changes, fix the following warnings:
drivers/net/wireless/mediatek/mt76/mt7915/mcu.h:32:37: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/mediatek/mt76/mt7915/mcu.h:40:37: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/mediatek/mt76/mt7915/mcu.h:49:37: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/mediatek/mt76/mt7915/mcu.h:58:37: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
Signed-off-by: Gustavo A. R. Silva <[email protected]>
Link: https://patch.msgid.link/Zr5KsZugaEXrApQJ@elsanto
Signed-off-by: Felix Fietkau <[email protected]>
Do not trigger full restarts when running into timeouts during SER.
Immediately abort MCU commands when firmware requests DMA restart.
Signed-off-by: Felix Fietkau <[email protected]>
- use reconfig_complete to restart mac_work / queues
- reset full wtbl after firmware init
- clear wcid and vif mask to avoid leak
Signed-off-by: Felix Fietkau <[email protected]>
When ieee80211_restart_hw is called, all interfaces and stations are
recreated. This can lead to corruption in the sta poll list, since
existing entries were not removed before their private data is reset.
Signed-off-by: Felix Fietkau <[email protected]>
- initialize and use per-sta wcid entry instead of vif wcid
- set wcid flags for 4addr/offload
- fix 'newly' argument for vif sta entry update
Signed-off-by: Felix Fietkau <[email protected]>
