This is a preliminary patch to add ethtool stats to mt7921 driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Similar to mt7915 driver, add tx/rx statistics reporting through ethtool.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce ethtool stats support to mt7921
driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move tx_amsdu histogram stats in mib_stats structure since registers are
clear-on-read
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Since it can run in parallel with mac_work, hold mutex lock in
mt7915_get_et_stats. Moreover update mib counters running
mt7915_get_et_stats.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_ethtool_worker_info in common code in order to be reused in
mt7921 driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to add ethtool stats to mt7921 driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Appears to have incorrectly offset 0x120 + 0x12 instead of 12 decimal,
leading to bogus power values being used.
Signed-off-by: Richard Huynh <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce mt7921s support.
Refactor mt7921_mcu_send_message to be sharable between mt7921s and
mt7921e.
Tested-by: Deren Wu <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rely on mcu_get_nic_capability to obtain Tx quota information
for the SDIO device, get PHY capability, MAC address and then we can
totally drop mt7921/eeprom.c and any unnecessary code.
Noting that mt76_connac_mcu_get_nic_capability should be run before set
flag MT76_STATE_MCU_RUNNING being set to setup the proper parameters
like Tx quota control before the device is started to running.
Tested-by: Deren Wu <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Extend mcu_get_nic_capability to obtain tx resource for SDIO device,
MAC address, and PHY capability.
Tested-by: Deren Wu <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add parse_irq to handle that interrupt status structure is
different between mt7663s and mt7921s.
This is a preliminary patch to introduce mt7921s driver
Tested-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move sdio common code in mt76_sdio module.
This is a preliminary patch to support mt7921s devices.
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use physical address to unify the register access and reorder the
entries in fixed_map table to accelerate the address lookup for
MT7921e. Cosmetics the patch with adding an extra space to make all
entries in the array style consistent.
Tested-by: Deren Wu <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The longer event such as the event for mcu_get_nic_capability would hold
the data in paged fragment skb for the SDIO device so we turn the skb to
be linearized skb before accessing it to reuse the same event parser
betweem mt7921s and mt7921e.
Tested-by: Deren Wu <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce mt7921s support.
MT7921_COMMON module grouping bus independent objects the both mt7921e and
mt7921s can share with and have to rely on.
Tested-by: Deren Wu <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce mt7921s support.
Make init.c reusable between mt7921s and mt7921e
Tested-by: Deren Wu <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce mt7921s support.
Make mcu.c reusable between mt7921s and mt7921e
Tested-by: Deren Wu <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce mt7921s support.
make dma.c be used dedicately for mt7921e.
by moving out mt7921_tx_cleanup from dma.c to mcu.c and then renaming
mt7921_tx_cleanup to refect the exact thing the function actually does.
Finally, dma.c totally become pcie specific one, only needed to
be compiled only when CONFIG_MT7921E is enabled.
Tested-by: Deren Wu <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce mt7921s support.
Split out a new pci_mac.c from mac.c to make mac.c reusable between
mt7921s and mt7921e.
Tested-by: Deren Wu <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove some more not used code in mt7915 debugfs.
Squash mt7915_puts_rate_txpower and mt7915_rate_txpower_show.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Export mt76s_alloc_rx_queue and mt76s_alloc_tx utility routines in order
to allow mt7921s driver to configure a different main rx queue.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce a dedicated mt76 debugfs sub-dir for ext-phy in dbdc mode.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to create a mt76 debugfs subir for ext-phy.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The VTA (Valid for Txd Arrival time) bit should be set in tx descriptor,
which is necessary for WM fw to schedule SPL (station priority list)
normally before generating txcmd.
If it's not set, some unexpected wcids may be involved in SPL.
Suggested-by: Nelson Chang <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
For broadcast/multicast wcid, the muar_idx should be 0xe.
Fixes: e57b7901469f ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rework starec tags to the order which firmware expected. This also fixes
some weird behaviors during generating SPL of HE-MU.
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix tag len error for sta_rec_wtbl, which causes fw parsing error for
the tags placed behind it.
Fixes: e57b7901469f ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
With this patch we can append txbf starec TLVs. This is an intermediate
patch to improve HE MUMIMO performances.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Beacon elements might be changed by hostapd configuraion, so driver
should compare both IEs and PHY capabilities to get the least common
denominator before association.
Co-developed-by: Evelyn Tsai <[email protected]>
Signed-off-by: Evelyn Tsai <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Even if it is a not real issue, add missing brackets in
mt7915_mcu_sta_bfer_ht routine in order to improve code readability
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fixes: d8d59f66d136 ("mt76: mt7615: support 16 interfaces").
commit 7f4b7920318b ("mt76: mt7615: add ibss support") introduced IBSS
and commit f4ec7fdf7f83 ("mt76: mt7615: enable support for mesh")
meshpoint support.
Both used in the "get_omac_idx"-function:
if (~mask & BIT(HW_BSSID_0))
return HW_BSSID_0;
With commit d8d59f66d136 ("mt76: mt7615: support 16 interfaces") the
ibss and meshpoint mode should "prefer hw bssid slot 1-3". However,
with that change the ibss or meshpoint mode will not send any beacon on
the mt7622 wifi anymore. Devices were still able to exchange data but
only if a bssid already existed. Two mt7622 devices will never be able
to communicate.
This commits reverts the preferation of slot 1-3 for ibss and
meshpoint. Only NL80211_IFTYPE_STATION will still prefer slot 1-3.
Tested on Banana Pi R64.
Signed-off-by: Nick Hainke <[email protected]>
Do not check status timestamp before DMA completion.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
