Check that val is not zero before aggr_per estimation in order to avoid a
possible division by 0
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The reference driver does not seem to enable it by default, only under certain
conditions, e.g. when a .bin file is loaded.
Make it opt-in via a device tree property for now, in case it is needed on some
boards.
Signed-off-by: Felix Fietkau <[email protected]>
The reference driver does not seem to enable it by default, only under certain
conditions, e.g. when a .bin file is loaded.
Make it opt-in via a device tree property for now, in case it is needed on some
boards.
Signed-off-by: Felix Fietkau <[email protected]>
When the EEPROM data is read from flash, it can contain tx DPD calibration
data. Add support for sending the data to the firmware.
Signed-off-by: Felix Fietkau <[email protected]>
When the EEPROM data is read from flash, it can contain DC offset calibration
data. Add support for sending the data to the firmware.
Signed-off-by: Felix Fietkau <[email protected]>
The reference driver does not seem to enable it by default, only under certain
conditions, e.g. when a .bin file is loaded.
Make it opt-in via a device tree property for now, in case it is needed on some
boards.
Signed-off-by: Felix Fietkau <[email protected]>
The function “platform_get_irq” can log an error already.
Thus omit a redundant message for the exception handling in the
calling function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mac80211/hostapd runs mt7615_set_channel with the same channel
parameters sending multiple rdd commands overwriting the previous ones.
This behaviour is causing tpt issues on dfs channels.
Fix the issue checking new channel freq/width with the running one.
Fixes: 5dabdf71e94e ("mt76: mt7615: add multiple wiphy support to the dfs support code")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rom patch is shared between Bluetooth and Wifi devices, so correct the
naming to allow two drivers to share the same file.
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce address parameter to mt7615_eeprom_init routine in order to be
reused adding usb support to mt7615 driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Generalize mt7615_rate_desc introducing mt7615_wtbl_desc and
mt7615_key_desc data structures in order to configure the hw wtbl
in a non-atomic context for usb devices
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove key dependency from mt7615_mac_wtbl_update_key and export
mt7615_mac_wtbl_update_key, mt7615_mac_wtbl_update_pk and
mt7615_mac_wtbl_update_cipher in order to reuse them in usb code.
Move mt7615_mac_get_cipher in mac.h
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rely on the mt7622 endpoint definitions for mt7663u
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt7615_mac_wtbl_addr in mac.h and add inline qualifier in order to
be reused adding usb support to mt7615 driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce __mt7663_load_firmware routine to load firmware for usb
devices.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move register configuration out of mt7615_mac_set_rates since usb
driver can't access device register in interrupt context. Introduce
mt7615_mac_update_rate_desc routine to report rate info to
mt7615_mac_set_rates
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce headroom and tailroom to mt76_mcu_ops data structure in order
to unify the routine used for mcu message allocation. This is a
preliminary patch to add mt7663u support
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove mt76_wr(dev, MT_CSR(0x010), 0x8208) that would cause
MT_PCIE_IRQ_ENABLE to be disabled; MT_PCIE_IRQ_ENABLE should always keep
on enabled when the driver is running.
0x44064 is a not existing address
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce rlm tlv header in bss_info mcu command in order to
inform the mcu about operating channel. Rlm header is necessary only if
the mcu is running low power functionalities (e.g offloaded scan)
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce BSS absence event that is reported when the fw
is leaving or entering current operational channel.
Signed-off-by: Sean Wang <[email protected]>
Co-developed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Keep Rx filters default value if the firmware supports offload and
low power features.
Signed-off-by: Sean Wang <[email protected]>
Co-developed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7615_mcu_set_channel_domain routines in order to instruct
the mcu about supported band/channels. This is a preliminary patch to
add hw scan support to mt7663e driver
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Disable dfs RDD mcu commands for mt7663 driver since they are not
currently supported by the 7663 firmware
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Make scs configurable per phy since most of the chipsets do not
support dbdc
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Simplify mib macros and use proper type for related counters.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add mt7610 PCI id found on D-Link DWR-960 to pci_device_id table.
Run-tested on D-Link DWR-960 with no-name half-size mPCIE card
with mt7610e.
Signed-off-by: Pawel Dembicki <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce Mercury UD13 dual-band dongle support to mt76x2u driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The current version has a new USB ID and reports as an 0x7632 device.
Adding the IDs results in it working out of the box.
Signed-off-by: Matthew Garrett <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Sobstitute sta_rec_wtbl data structure with tlv one
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7615_mcu_uni_set_ba routine in order to add support
for mt7663e driver
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7615_mcu_uni_set_bss, mt7615_mcu_uni_set_dev and
mt7615_mcu_uni_set_beacon_offload uni mcu commands. This is a
preliminary patch to add mt7663e support
Signed-off-by: Sean Wang <[email protected]>
Co-developed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7615_mcu_uni_set_bmc and mt7615_mcu_uni_set_sta routines for
mt7663e commands.
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mcu uni command type. Uni commands rely on a stripped verions
of mt7615_mcu_txd data strutture. Split mt7615_mcu_txd_common and
mt7615_mcu_txd. Uni commands will be use by mt7663e driver
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
