When disabling beacons on a vif, intval is 0. Ensure that dev->mt76.beacon_int
is not overwritten in this case, so that beacons continue to work for other
interfaces.
Signed-off-by: Felix Fietkau <[email protected]>
Move hw data queues in mt76_phy from mt76_dev since mt7915 supports per
phy hw queues in dbdc mode
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rely on mt76_queue instead of qid in tx_queue_skb signature.
This is a preliminary patch to move data queues in mt76_phy and add
dbdc support to mt7915 driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to move data queues in mt76_phy and properly
support dbdc
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <[email protected]>
Signed-off-by: Allen Pais <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This fixes the following checkpatch warnings:
WARNING: Improper SPDX comment style
CHECK: No space is necessary after a cast
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Disable pre_tbtt_tasklet tasklet before setting the operating channel.
Enable/disable beacon_timer in mt7603_set_channel
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move beacon_mask in mt76_dev data structure since it is used by
all drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move beacon_int in mt76_dev data structure since it is used by
all drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
As already done for mt76_dma_tx_queue_skb_raw, add static qualifier to
mt76_dma_tx_queue_skb and introduce mt76_tx_queue_skb in order to run
mt76_dma_tx_queue_skb in driver code
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt76_sw_queue data structure in order to support new
chipsets (e.g. mt7615) that have a shared hardware queue for all traffic
identifiers. mt76_sw_queue will be used to track outstanding packets
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove mt76_queue dependency from tx_queue_skb function pointer and
rely on mt76_tx_qid instead. This is a preliminary patch to introduce
mt76_sw_queue support
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
__sw_hweight8() is only defined if CONFIG_GENERIC_HWEIGHT is enabled.
The function that works on all architectures is hweight8().
Signed-off-by: Felix Fietkau <[email protected]>
For some reason the BMC queue flush does not work properly if packets were
queued for a BSS0_n interface (secondary vif).
Work around this issue by using the DMA scheduler to filter the queue before
issueing the BMC queue flush.
Signed-off-by: Felix Fietkau <[email protected]>
It is not necessary to time the start of the queue in software, the hardware
already does that for us.
Move all processing into the pre-tbtt tasklet to get rid of a race condition
that could happen when the pre-tbtt tasklet takes too long
Signed-off-by: Felix Fietkau <[email protected]>
Felix Fietkau