Each rate retry slot takes up MT7603_RATE_RETRY tries, and cannot be altered
based on mac80211 provided rate retry counts.
Signed-off-by: Felix Fietkau <[email protected]>
The second chain value is 0 if the second chain is disabled, which
would make the reported signal strength 0 as well.
Signed-off-by: Felix Fietkau <[email protected]>
Port mt76x02_check_tx_hang watchdog from vendor driver in order to
perform a device reset when tx mac/dma logic hangs. Tx mac/dma stuck
has been observed when the device is heavy loaded or in a noisy
environment. Moreover introduce wdt delayed work in order to run
tx_hang watchdog. For the moment run mt76x02_check_tx_hang watchdog
just on mt76x2 devices since the issue has not been observed on mt76x0
driver yet
Signed-off-by: Lorenzo Bianconi <[email protected]>
Precompute data length in order to avoid to allocate the related
skb data structure if reported length does not fit in queue buf_size
Signed-off-by: Lorenzo Bianconi <[email protected]>
Do not set bw variable to zero for legacy rates since it is already
initialized to zero. Moreover set nss to 1 just for legacy rates
since nss will be properly set for VHT/HT rates
Signed-off-by: Lorenzo Bianconi <[email protected]>
Ported from the reference driver. Should fix compliance with ETSI
regulatories on preventing transmission while energy detect values
are above the threshold.
The code has been tested using an ath9k device running tx99 as
noise generator
Signed-off-by: Lorenzo Bianconi <[email protected]>
Grab mt76_dev mutex in mt76x02_dfs_set_domain since it runs
concurrently with mt76x{0,2}_set_channel routines
Signed-off-by: Lorenzo Bianconi <[email protected]>
Configure protection based on information that are provided to
us either by remote AP or by hostapd via HT operation IE.
Signed-off-by: Stanislaw Gruszka <[email protected]>
On new mt76 chips, phy mode is configured by last 3 bits
of rate value. Hence OFDM bit is marked by 0x2000
instead of 0x4000.
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Stanislaw Gruszka <[email protected]>
Use set_rts_threshold calback to enable/disable threshold only for
legacy traffic.
Protection for HT and VHT traffic is defined by HT operation element
and it's provided by remote AP or by hostapd.
Signed-off-by: Stanislaw Gruszka <[email protected]>
As already done for pcie code in commit 79d1c94c9c78 ("mt76: avoid
queue/status spinlocks while passing tx status to mac80211") make sure
that no tx related spinlocks are taken during the ieee80211_tx_status call
Signed-off-by: Lorenzo Bianconi <[email protected]>
Grab mt76_dev mutex in mt76x02_mac_work handler since it runs
concurrently with mt76x{0,2}_set_channel routines
Signed-off-by: Lorenzo Bianconi <[email protected]>
Reconfigure properly MT_MAC_SYS_CTRL register after mac sw-reset
in mt76x02_check_mac_err routine
Fixes: 73556561ab9f ("mt76x0: use mt76x02_mac_work as stats handler")
Signed-off-by: Lorenzo Bianconi <[email protected]>
MODULE_FIRMWARE() is used in usb_mcu.c and provided by linux/module.h,
but this header file is not directly included. This causes problems in
backports with some kernel versions.
Add the missing include.
Signed-off-by: Hauke Mehrtens <[email protected]>
Precompute data length in order to avoid to allocate the related
skb data structure if reported length does not fit in queue buf_size
Signed-off-by: Lorenzo Bianconi <[email protected]>
Remove napi from mt76_dma_rx_fill routine signature since
it is a leftover of a previous implementation and it is no
longer used
Signed-off-by: Lorenzo Bianconi <[email protected]>
Some mt7603e chip has empty efuse data.
In this case driver will crash due to dereferencing NULL pointer.
The mt7603_eeprom_load will return success directly if the chip has no efuse
data and dev->mt76.otp.data is left empty, i.e. NULL pointer.
The mt7603_eeprom_init will then try to dereference dev->mt76.otp.data
without checking its value.
This patch adds a check around these codes to prevent kernel panic.
Signed-off-by: Weijie Gao <[email protected]>
Sometimes during startup, the MCU response time can be quite long,
especially in newer versions. This change prevents false timeout errors
Signed-off-by: Felix Fietkau <[email protected]>
Ported from the reference driver.
Should fix compliance with ETSI rules on preventing transmission while
energy detect values are above the threshold.
Relax rules for non-ETSI regdomains
Signed-off-by: Felix Fietkau <[email protected]>
It is not necessary to time the start of the queue in software, the hardware
already does that for us.
Move all processing into the pre-tbtt tasklet to get rid of a race condition
that could happen when the pre-tbtt tasklet takes too long
Signed-off-by: Felix Fietkau <[email protected]>
Felix Fietkau