This is a preliminary patch to simplify setting state in mt7915
testmode, for adding the new continuous tx state.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Support to set a special tx state in testmode: continuous tx,
which is used for sending tx without time gap.
Note that continuous tx mode doesn't send real packets, instead, it's
pure phy signal, and the waveform can be observed by instrument.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add a testmode mcu command to clean up hw tx queue before a new
testmode tx starts.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
If tx_time is set, calculate a new packet length based on tx time and
tx rate.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add support to calculate and apply ipg parameters in testmode
for MT7915 NIC.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Split parameter settings and mcu command update in mt7915_mcu_set_tx().
This is for reusing edca update function in testmode ipg setting.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Originally, tx queued limit is set to 1000 to prevent from running out
of tx token. If a new testmode tx is triggered while the previous one
hasn't finished yet, we'll wait a period of time until tx_done equals to
tx_queued. Normally, current queued limit can finish in 10 seconds.
However, if ipg is configured to a larger value, less than 1000 packets
can be done in the default timeout period, which may lead to a crash
when a new testmode tx triggered.
To deal with this, make tx queued limit dynamically adjusted according
to ipg value.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add attributes for setting tx inter-packet gap (ipg), duty cycle, and
transmission time in testmode.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add spatial extension (spe) index as a configurable parameter in testmode.
This is used for specifically configuring TX path, such as different
WF TX priority, number of antennas and spatial streams.
If spe_idx is not set, TX path depends on tx_antenna_mask; otherwise,
both spe_idx and tx_antenna_mask are referenced to decide TX path.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
LDPC should be set when bw is larger than 20MHz to make
testmode tx work normally.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move chainmask from driver phy to mt76_phy since it is used by all
drivers. This is a preliminary patch to create a common mcu library used
by mt7615 and mt7921 drivers
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mac_work delayed_work and mac_work_count in mt76_phy since it is
used by all drivers. This is a preliminary patch to create a common mcu
library used by mt7615 and mt7921 drivers
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The mcs value of HT mode reported by mt7915_mcu_get_rx_rate()
has already been converted to the expected format.
Tested-by: Yiwei Chung <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move per-chip testmode data to mt7615_phy, to properly support
reg_backup and rx status of each band in testmode.
Signed-off-by: Shayne Chen <[email protected]>
Acked-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move per-chip testmode data to mt7915_phy, to properly support
reg_backup and rx status of each band in testmode.
Signed-off-by: Shayne Chen <[email protected]>
Acked-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move testmode mtd variables to mt76_dev, since they are the same on
each phy.
Signed-off-by: Shayne Chen <[email protected]>
Acked-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add testmode support for DBDC NICs (both MT7615D and MT7915D work).
Testmode data and parameters are moved from per-dev to per-phy
for maintaining the value of each band.
Signed-off-by: Shayne Chen <[email protected]>
Acked-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch for DBDC and ipg config support
in testmode.
The wmm_idx of band1 should be configured by this command to
make band1 Tx work normally. Also, for setting ipg, FW needs a
non-empty bss_info structure to do edca parameters update.
Signed-off-by: Shayne Chen <[email protected]>
Acked-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Kernel test robot reported warning:
drivers/net/wireless/mediatek/mt76/tx.c: In function
'mt76_txq_schedule':
>> drivers/net/wireless/mediatek/mt76/tx.c:499:21: warning: variable 'q'
>> set but not used [-Wunused-but-set-variable]
499 | struct mt76_queue *q;
| ^
Reported-by: kernel test robot <[email protected]>
Signed-off-by: Souptick Joarder <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Clang warns in both mt7615 and mt7915:
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:271:9: warning: implicit
conversion from enumeration type 'enum mt76_mcuq_id' to different
enumeration type 'enum mt76_txq_id' [-Wenum-conversion]
txq = MT_MCUQ_FWDL;
~ ^~~~~~~~~~~~
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:278:9: warning: implicit
conversion from enumeration type 'enum mt76_mcuq_id' to different
enumeration type 'enum mt76_txq_id' [-Wenum-conversion]
txq = MT_MCUQ_WA;
~ ^~~~~~~~~~
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:282:9: warning: implicit
conversion from enumeration type 'enum mt76_mcuq_id' to different
enumeration type 'enum mt76_txq_id' [-Wenum-conversion]
txq = MT_MCUQ_WM;
~ ^~~~~~~~~~
3 warnings generated.
drivers/net/wireless/mediatek/mt76/mt7615/mcu.c:238:9: warning: implicit
conversion from enumeration type 'enum mt76_mcuq_id' to different
enumeration type 'enum mt76_txq_id' [-Wenum-conversion]
qid = MT_MCUQ_WM;
~ ^~~~~~~~~~
drivers/net/wireless/mediatek/mt76/mt7615/mcu.c:240:9: warning: implicit
conversion from enumeration type 'enum mt76_mcuq_id' to different
enumeration type 'enum mt76_txq_id' [-Wenum-conversion]
qid = MT_MCUQ_FWDL;
~ ^~~~~~~~~~~~
2 warnings generated.
Use the proper type for the queue ID variables to fix these warnings.
Additionally, rename the txq variable in mt7915_mcu_send_message to be
more neutral like mt7615_mcu_send_message.
Fixes: e637763b606b ("mt76: move mcu queues to mt76_dev q_mcu array")
Link: https://github.com/ClangBuiltLinux/linux/issues/1229
Signed-off-by: Nathan Chancellor <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Hardware wouldn't add LLC-SNAP when skb->data_len is 0, which causes
Tx hang, so add a check to drop this kind of packet.
Tested-by: Bo Jiao <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix the following sparse warning in mt7915_mcu_set_radar_th routine:
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:3154:17: warning: incorrect type in initializer (different base types)
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:3154:17: expected unsigned int [usertype] min_pri
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:3154:17: got restricted __le32 [usertype]
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:3155:17: warning: incorrect type in initializer (different base types)
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:3155:17: expected unsigned int [usertype] max_pri
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:3155:17: got restricted __le32 [usertype]
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:3162:17: warning: incorrect type in initializer (different base types)
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:3162:17: expected unsigned int [usertype] min_stgpr_diff
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:3162:17: got restricted __le32 [usertype]
Fixes: cee236e1489ec ("mt76: mt7915: fix endian issues")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add support for getting rf values from flash.
This is used for some test purposes and products.
If the mtd partition is configured in dts, driver will read from flash
to init eeprom command; if not, still init it with efuse's values.
An example:
&slot0 {
mt7915@0,0 {
reg = <0x0000 0 0 0 0>;
device_type = "pci";
mediatek,mtd-eeprom = <&factory 0x0000>;
};
};
Acked-by: Ryder Lee <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In order to avoid races, run mt7915_configure_filter routine holding
mt76 mutex
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Replace a comma between expression statements by a semicolon.
Signed-off-by: Zheng Yongjun <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Replace a comma between expression statements by a semicolon.
Signed-off-by: Zheng Yongjun <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Reset token in mt7615_mac_reset_work() to avoid possible leakege.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Reset buffering token in mt7915_mac_reset_work() to avoid possible leakege,
which leads to Tx stop after mac reset.
Tested-by: Bo Jiao <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
MCU expects to set WLAN_CIPHER_SUITE_CCMP and WLAN_CIPHER_SUITE_AES_CMAC
at the same time, so adding an intermediate buffer for batch update.
Tested-by: Sujuan Chen <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix a possible NULL pointer dereference in mt76s_process_tx_queue that
can occur if status thread runs before allocating tx queues
Fixes: 6a618acb7e62 ("mt76: sdio: convert {status/net}_work to mt76_worker")
Signed-off-by: Lorenzo Bianconi <[email protected]>
This is causing some extreme latency spikes when sending traffic to
multiple stations at the same time. Disable this until the firmware issue
is sorted out
Signed-off-by: Felix Fietkau <[email protected]>
Instead of stopping and waking only a single queue, handle all phy tx queues
mapped ot the same hardware queue.
Also allow the driver to block tx queues
Signed-off-by: Felix Fietkau <[email protected]>
mt7915 automatically detects dbdc feature so drop debugfs knob.
Move if_comb, mt7915_rates, if_limits structs and mt7915_regd_notifier(),
mt7915_init_wiphy() routines at the begging of init.c in order to make
mt7915_register_ext_phy routine static
Co-developed-by: Shayne Chen <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
