Introduce p2p-go/p2p-client support to mt7921 driver
CONNECTION_P2P_GC/GO is not supported with the current firmware
so we added mt76_dev to mt76_connac_mcu_sta_basic_tlv signature to
use CONNECTION_INFRA_STA/AP instead for p2p-client and p2p-go
respectively to make it work.
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When the BIOS has been configured for Fast Boot, systems with mt7921e
have non-functional wifi. Turning on Fast boot caused both bus master
enable and memory space enable bits in PCI_COMMAND not to get configured.
The mt7921 driver already sets bus master enable, but explicitly check
and set memory access enable as well to fix this problem.
Tested-by: Anson Tsao <[email protected]>
Signed-off-by: Mario Limonciello <[email protected]>
Acked-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
FIF_* flags from mac80211 is not ABI. mt7921 should not pass it into mcu
directly. Remap FIF_* to driver defined flags as mcu command input.
Fixes: c222f77fd421 ("wifi: mt76: mt7921: fix rx filter incorrect by drv/fw inconsistent")
Signed-off-by: Neil Chen <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Since the fw offload capability check is shared between pci,usb and sdio
devices, move it in common init code and reduce code duplication.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Currently using BSS_INFO_PS command will sometimes cause packet drop in
hw rx queue.
Temporarily remove this function until finding the cause.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Init mpdu density based on the hardware capability to prevent rx drop.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix the tail and data pointers. The rxd->len in mt7996_mcu_rxd does not
include the length of general rxd. It only includes the length of
firmware event rxd. Use skb->length to get the correct length.
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Tri-band chipsets support one band on each a-die, so remove the unused
definition of eeprom band selection.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Pass qid into mt7996_mac_write_txwi() to let the tx descriptor of
non-bufferable MMPDUs be filled with correct hw queue index.
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Those capabilities have been added into ieee80211_bss_conf.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Those capabilities have been added into ieee80211_bss_conf.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
According to the documentation, ieee80211_rx_list must not run concurrently
with ieee80211_tx_status (or its variants).
Cc: [email protected]
Fixes: 88046b2c9f6d ("mt76: add support for reporting tx status with skb")
Reported-by: Brian Coverstone <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This helps avoid cleartext leakage of already queued or powersave buffered
packets, when a reassoc triggers the key deletion.
Cc: [email protected]
Signed-off-by: Felix Fietkau <[email protected]>
This fixes the following compile error when compiling against recent
glibc:
------------
/tools/eeprom.c:223:9: error: ignoring return value of 'fread' declared with attribute 'warn_unused_result' [-Werror=unused-result]
223 | fread(buf, 1, EEPROM_PART_SIZE, f);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
------------
Signed-off-by: Hauke Mehrtens <[email protected]>
There's no keep-alive packet being received by mac80211 stack when WED
is enabled, which leads to tx BA session timeout. This patch calls
ieee80211_refresh_tx_agg_session_timer() to refresh timer according
to tx status reporting.
Signed-off-by: Ryder Lee <[email protected]>
Trying to probe a mt7921e pci card without firmware results in a
successful probe where ieee80211_register_hw hasn't been called. When
removing the driver, ieee802111_unregister_hw is called unconditionally
leading to a kernel NULL pointer dereference.
Fix the issue running mt76_unregister_device routine just for registered
hw.
Link: https://bugs.debian.org/1029116
Link: https://bugs.kali.org/view.php?id=8140
Reported-by: Stuart Hayhurst <[email protected]>
Fixes: 1c71e03afe4b ("mt76: mt7921: move mt7921_init_hw in a dedicated work")
Tested-by: Helmut Grohne <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
A number of users reported that this support was working fine before
it got removed. Add it back, but leave out the unsupported 80+80 mode.
Fixes: ac922bd60ace ("wifi: mt76: mt7915: remove BW160 and BW80+80 support")
Signed-off-by: Felix Fietkau <[email protected]>
The scatter and gather frame may be incorrect because WED and WO may
send frames to host driver interleaved.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Sujuan Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
If kernel do not enable CONFIG_HWMON, it may cause thermal
initialization to be done with temperature value 0 and then can not
transmit. This commit fixes it by setting trigger/restore temperature
before checking CONFIG_HWMON.
Fixes: 7d12b38ab6f6 ("wifi: mt76: mt7915: call mt7915_mcu_set_thermal_throttling() only after init_work")
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Enable two PCIe interfaces (dev->hif2) support for mt7916 when WED is enabled.
Signed-off-by: Sujuan Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
On MT7986 the WiFi driver currently does not get automatically loaded,
requiring manual modprobing because the device tree compatibles are not
exported into metadata.
Add the missing MODULE_DEVICE_TABLE macro to fix this.
Fixes: 99ad32a4ca3a2 ("mt76: mt7915: add support for MT7986")
Signed-off-by: Lorenz Brun <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Allow AP to change channel width for 40Mhz intolerant STA on the
2.4 GHz band.
Signed-off-by: Himanshu Goyal <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The 11be generation's radiotap bitfields were wrongly copy-and-pasted
from 11ax driver, so fix them accordingly.
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Drop the lock before returning -EINVAL.
Fixes: ecaccdae7a7e ("wifi: mt76: mt7915: rework mt7915_thermal_temp_store()")
Signed-off-by: Dan Carpenter <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt7921 just stop some workers and clean up chip status before reboot.
In stress test, there are working activities still running at the period
of .shutdown callback and that would cause some hosts cannot recover
DMA after reboot. To avoid the floating state in reboot, we use
mt7921_pci_remove() to fully deinit all resources.
Fixes: f23a0cea8bd6 ("wifi: mt76: mt7921e: add pci .shutdown() support")
Signed-off-by: Deren Wu <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Should not use AND operator to check vif type NL80211_IFTYPE_MONITOR, and
that will cause we go into sniffer command for both STA and MONITOR
mode. However, the sniffer command would set channel properly (with some
extra options), the STA mode still works even if using the wrong
command.
Fix vif type check to make sure we using the right command to update
channel.
Fixes: 914189af23b8 ("wifi: mt76: mt7921: fix channel switch fail in monitor mode")
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Some combinations of hosts cannnot detect mt7921e after reboot. The
interoperability issue is caused by the status mismatch between host
and chip fw. In such cases, the driver should stop chip activities
and reset chip to default state before reboot.
Suggested-by: [email protected]
Co-developed-by: Deren Wu <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Leon Yen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
PCI power state and wakeup are already handled by PCI core, so it's not
necessary to handle them in the driver.
Also switch to use pm_sleep_ptr() to remove #ifdef guard.
Signed-off-by: Kai-Heng Feng <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Run mt76x02_set_ethtool_fwver utility routine in mt76x0u_load_firmware()
in order to report firmware version through ethtool
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rework and extract common code of capability init for the preparation of
adding EHT capability.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add helpers to get the maximum wtbl size and interface num based
on hw caps.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
There are variants of mt7996 which are different from eht supported and
wtbl size limit. Get the hw caps with CHIP_CONFIG command.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add support to get EHT rate stats from ethtool.
This is the preliminary patch to add EHT support for mt7996.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Increase wcid size to support up to 1024 station hw entries and
64 bcast/mcast hw entries.
This is the preliminary patch to add EHT support for mt7996.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is the preliminary patch to add EHT support for mt7996.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add helpers to get eht cap and phymode on different bands and vifs.
This is the preliminary patch to add EHT support for mt7996.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
