Enable 160MHz beamformee support on mt7922 by updating HE capability
element configuration. Previously, only 160MHz channel width was set,
but beamformee for 160MHz was not properly advertised. This patch
adds BEAMFORMEE_MAX_STS_ABOVE_80MHZ_4 capability to allow devices
to utilize 160MHz BW for beamforming.
Tested by connecting to 160MHz-bandwidth beamforming AP and verified
HE capability.
Signed-off-by: Quan Zhou <[email protected]>
Link: https://patch.msgid.link/ae637afaffed387018fdc43709470ef65898ff0b.1756383627.git.quan.zhou@mediatek.com
Signed-off-by: Felix Fietkau <[email protected]>
The mt7925 sometimes fails to enter low power mode during suspend.
This is caused by the chip firmware sending an additional ACK event
to the host after processing the suspend command. Due to timing issues,
this event may not reach the host, causing the chip to get stuck.
To resolve this, the ACK flag in the suspend command is removed,
as it is not needed in the MT7925 architecture. This prevents the
firmware from sending the additional ACK event, ensuring the device
can reliably enter low power mode during suspend.
Signed-off-by: Quan Zhou <[email protected]>
Link: https://patch.msgid.link/d056938144a3a0336c3a4e3cec6f271899f32bf7.1736775666.git.quan.zhou@mediatek.com
Signed-off-by: Felix Fietkau <[email protected]>
When the system suspend or resume, the WiFi driver sends
an hif_ctrl command to the firmware and waits for an event.
Due to changes in the event format reported by the chip, the
current mt7925's driver does not account for these changes,
resulting in command timeout. Add flow to handle hif_ctrl
event to avoid command timeout. We also exented API
mt76_connac_mcu_set_hif_suspend for connac3 this time.
Signed-off-by: Quan Zhou <[email protected]>
Link: https://patch.msgid.link/3a0844ff5162142c4a9f3cf7104f75076ddd3b87.1735910562.git.quan.zhou@mediatek.com
Signed-off-by: Felix Fietkau <[email protected]>
When enter suspend/resume while in a connected state, the upper layer
will trigger disconnection before entering suspend, and at the same time,
it will trigger regd_notifier() and update CLC, causing the CLC event to
not be received due to suspend, resulting in a command timeout.
Therefore, the update of CLC is postponed until resume, to ensure data
consistency and avoid the occurrence of command timeout.
Signed-off-by: Quan Zhou <[email protected]>
Link: https://patch.msgid.link/bab00a2805d0533fd8beaa059222659858a9dcb5.1735910455.git.quan.zhou@mediatek.com
Signed-off-by: Felix Fietkau <[email protected]>
A sub-process of Wifi L0.5 reset will make chip common partition
enter low power, and have chance lead to Bluetooth host-to-chip
command timeout, modify the software flow according to the chip's
design to solve the problem.
Fixes: c948b5da6bbe ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Signed-off-by: Quan Zhou <[email protected]>
Signed-off-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
For some cases as below, we may encounter the unpreditable chip stats
in driver probe()
* The system reboot flow do not work properly, such as kernel oops while
rebooting, and then the driver do not go back to default status at
this moment.
* Similar to the flow above. If the device was enabled in BIOS or UEFI,
the system may switch to Linux without driver fully shutdown.
To avoid the problem, force push the device back to default in probe()
* mt7921e_mcu_fw_pmctrl() : return control privilege to chip side.
* mt7921_wfsys_reset() : cleanup chip config before resource init.
Error log
[59007.600714] mt7921e 0000:02:00.0: ASIC revision: 79220010
[59010.889773] mt7921e 0000:02:00.0: Message 00000010 (seq 1) timeout
[59010.889786] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59014.217839] mt7921e 0000:02:00.0: Message 00000010 (seq 2) timeout
[59014.217852] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59017.545880] mt7921e 0000:02:00.0: Message 00000010 (seq 3) timeout
[59017.545893] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59020.874086] mt7921e 0000:02:00.0: Message 00000010 (seq 4) timeout
[59020.874099] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59024.202019] mt7921e 0000:02:00.0: Message 00000010 (seq 5) timeout
[59024.202033] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59027.530082] mt7921e 0000:02:00.0: Message 00000010 (seq 6) timeout
[59027.530096] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59030.857888] mt7921e 0000:02:00.0: Message 00000010 (seq 7) timeout
[59030.857904] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59034.185946] mt7921e 0000:02:00.0: Message 00000010 (seq 8) timeout
[59034.185961] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59037.514249] mt7921e 0000:02:00.0: Message 00000010 (seq 9) timeout
[59037.514262] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59040.842362] mt7921e 0000:02:00.0: Message 00000010 (seq 10) timeout
[59040.842375] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59040.923845] mt7921e 0000:02:00.0: hardware init failed
Fixes: 5c14a5f944b9 ("mt76: mt7921: introduce mt7921e support")
Tested-by: Kai-Heng Feng <[email protected]>
Co-developed-by: Leon Yen <[email protected]>
Signed-off-by: Leon Yen <[email protected]>
Signed-off-by: Quan Zhou <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Tested-by: Juan Martinez <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In system warm reboot scene, due to the polling timeout(now 1000us)
is too short to wait dma idle in time, it may make driver probe fail
with error code -ETIMEDOUT. Meanwhile, we also found the dma may take
around 70ms to enter idle state. Change the polling idle timeout to
100ms to avoid the probabilistic probe fail.
Tested pass with 5000 times warm reboot on x86 platform.
[4.477496] pci 0000:01:00.0: attach allowed to drvr mt7921e [internal device]
[4.478306] mt7921e 0000:01:00.0: ASIC revision: 79610010
[4.480063] mt7921e: probe of 0000:01:00.0 failed with error -110
Fixes: 0a1059d0f060 ("mt76: mt7921: move mt7921_dma_reset in dma.c")
Signed-off-by: Quan Zhou <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
If the chip reset worker is triggered during the remove process, the chip
DMA may not be properly pushed back to the idle state. This can lead to
corruption of the DMA flow due to the chip reset. Therefore, it is
necessary to stop the chip reset before the DMA is finalized.
To avoid resetting the chip after the reset worker is cancelled, use
__mt7921_mcu_drv_pmctrl() instead of mt7921_mcu_drv_pmctrl(). It is safe to
ignore the pm mutex because the pm worker and wake worker have already been
cancelled.
Fixes: 033ae79b3830 ("mt76: mt7921: refactor init.c to be bus independent")
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Co-developed-by: Deren Wu <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Co-developed-by: Wang Zhao <[email protected]>
Signed-off-by: Wang Zhao <[email protected]>
Signed-off-by: Quan Zhou <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The hardware team has advised the driver that it is necessary to first put
WFDMA into an idle state before resetting the WFDMA. Otherwise, the WFDMA
may enter an unknown state where it cannot be polled with the right state
successfully. To ensure that the DMA can work properly while a stressful
cold reboot test was being made, we have reordered the programming sequence
in the driver based on the hardware team's guidance.
The patch would modify the WFDMA disabling flow from
"DMA reset -> disabling DMASHDL -> disabling WFDMA -> polling and waiting
until DMA idle" to "disabling WFDMA -> polling and waiting for DMA idle ->
disabling DMASHDL -> DMA reset.
Where he polling and waiting until WFDMA is idle is coordinated with the
operation of disabling WFDMA. Even while WFDMA is being disabled, it can
still handle Tx/Rx requests. The additional polling allows sufficient time
for WFDMA to process the last T/Rx request. When the idle state of WFDMA is
reached, it is a reliable indication that DMASHDL is also idle to ensure it
is safe to disable it and perform the DMA reset.
Fixes: 0a1059d0f060 ("mt76: mt7921: move mt7921_dma_reset in dma.c")
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Co-developed-by: Deren Wu <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Co-developed-by: Wang Zhao <[email protected]>
Signed-off-by: Wang Zhao <[email protected]>
Signed-off-by: Quan Zhou <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In ACPI enabled devices, mt7921 should read MTFG table from platform
hardware. Apply necessary settings for firmware capabilities through CLC
command.
Co-developed-by: Deren Wu <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Quan Zhou <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
