Currently, per-radio attributes are set on per-phy basis, i.e., all the
radios present in a wiphy will take attributes values sent from user. But
each radio in a wiphy can get different values from userspace based on
its requirement.
To extend support to set per-radio attributes, add support to get radio
index from userspace. Add an NL attribute - NL80211_ATTR_WIPHY_RADIO_INDEX,
to get user specified radio index for which attributes should be changed.
Pass this to individual drivers, so that the drivers can use this radio
index to change per-radio attributes when necessary. Currently, per-radio
attributes identified are:
NL80211_ATTR_WIPHY_TX_POWER_LEVEL
NL80211_ATTR_WIPHY_ANTENNA_TX
NL80211_ATTR_WIPHY_ANTENNA_RX
NL80211_ATTR_WIPHY_RETRY_SHORT
NL80211_ATTR_WIPHY_RETRY_LONG
NL80211_ATTR_WIPHY_FRAG_THRESHOLD
NL80211_ATTR_WIPHY_RTS_THRESHOLD
NL80211_ATTR_WIPHY_COVERAGE_CLASS
NL80211_ATTR_TXQ_LIMIT
NL80211_ATTR_TXQ_MEMORY_LIMIT
NL80211_ATTR_TXQ_QUANTUM
By default, the radio index is set to -1. This means the attribute should
be treated as a global configuration. If the user has not specified any
index, then the radio index passed to individual drivers would be -1. This
would indicate that the attribute applies to all radios in that wiphy.
Signed-off-by: Roopni Devanathan <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Johannes Berg <[email protected]>
The implementation amounts to setting the driver flag
IEEE80211_VIF_SUPPORTS_CQM_RSSI, and then providing
mechanisms for continuously updating enough information
to be able to provide notifications to userspace when
RSSI drops below a certain threshold
Signed-off-by: Jack Kao <[email protected]>
Signed-off-by: Ming Yen Hsieh <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
MediaTek has asked to switch from the ISC license to BSD-3-Clause-Clear,
in order to improve clarity and the legal integrity of the code.
The BSD-3-Clause license includes the "no endorsement" clause, which is
important for protecting the reputation of the original authors and
contributors by preventing unauthorized use of their names for endorsement
purposes.
This clause is absent in the BSD-2-Clause license, which is more permissive
but lacks this specific protection.
This change also cleans up the license of some Kconfig/Makefile files,
which were accidentally marked as GPL.
The GPL 2.0 remains in use on mt76x0, as well as two source files in mt7615
for which the license situation still needs to be clarified.
Signed-off-by: Felix Fietkau <[email protected]>
The test mode interface allows controlled execution of chip-level
operations such as continuous transmission, reception tests, and
register access, which are essential during bring-up, diagnostics,
and factory testing.
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Michael Lo <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Refine the disconnection cleanup process for MLO. It introduces a dedicated
function to handle device removal, ensuring proper resource cleanup for both
BSS and device information.
Fixes: 21e40c17361e ("wifi: mt76: mt7925: adjust rm BSS flow to prevent next connection failure")
Signed-off-by: Ming Yen Hsieh <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Similar to the mt7921, seems the code was copy-paste from there. This
bug was noticed by me and confirmed by many more people using this
chipset with openwrt: https://github.com/openwrt/mt76/issues/783
It seems that for this particular chipset the mt76_phy->txpower_cur is
never set, like in the case of other chipsets like mt7603, mt7615, etc.
The driver is correctly calculating the TX power adjustment based on the
number of antennas. However, the base TX power (phy->txpower_cur) is not
being properly initialized or set to a meaningful value. It's starting
at 0, so the final result is just the antenna gain compensation divided
by 2.
Signed-off-by: Razvan Grigore <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Some countries do not support EHT modulation for now. To prevent violating
regulations, the MT7925 chipset should control the EHT capabilities.
Therefore, when a regulatory domain change is detected during scanning,
the `mt7925_regd_be_ctrl` will process the CLC data to update the EHT
capabilities.
Signed-off-by: Ming Yen Hsieh <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
This patch introduces MLO capability control for the MT792x Wi-Fi driver.
It removes the unused `MT792x_CHIP_CAP_MLO_EVT_EN` flag and introduces new
capability flags `MT792x_CHIP_CAP_MLO_EN` and `MT792x_CHIP_CAP_MLO_EML_EN`
to enable MLO and EML features based on firmware capabilities.
Signed-off-by: Ming Yen Hsieh <[email protected]>
Reviewed-by: Sabeeh Khan <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Properly retrieve the response for commands with events. Ensure accurate
handling of event-driven commands.
Fixes: 86c051f2c418 ("wifi: mt76: mt7925: enabling MLO when the firmware supports it")
Signed-off-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
In mt7925_mac_link_bss_add(), the mt76_connac_mcu_uni_add_dev() function
must be executed only after all parameters have been properly initialized.
Fixes: 86c051f2c418 ("wifi: mt76: mt7925: enabling MLO when the firmware supports it")
Signed-off-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
This commit extends the `mt76_connac_mcu_uni_add_dev` function to include
support for Multi-Link Operation (MLO). Additionally, backward
compatibility for MT7921 is preserved, enabling seamless integration with
existing setups.
Fixes: 86c051f2c418 ("wifi: mt76: mt7925: enabling MLO when the firmware supports it")
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
In mt7925_change_vif_links() devm_kzalloc() may return NULL but this
returned value is not checked.
Fixes: 69acd6d910b0 ("wifi: mt76: mt7925: add mt7925_change_vif_links")
Signed-off-by: Charles Han <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Rework connac helpers related to rate and phymode.
This is a preliminary patch to add MLO support for mt7996 chipsets.
Co-developed-by: Bo Jiao <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In multi-channel scenarios, the granted channel must be aborted before
suspending. Otherwise, the firmware will be put into a wrong state,
resulting in an association failure after resuming.
With this patch, the granted channel will be aborted before suspending
if necessary.
Cc: [email protected]
Fixes: c948b5da6bbe ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Signed-off-by: Michael Lo <[email protected]>
Signed-off-by: Ming Yen Hsieh <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Also report auth/disassoc events, in order to give the driver more control over
handling the station state.
Signed-off-by: Felix Fietkau <[email protected]>
