This patch does not change any logic, just improve code readability.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
round_jiffies_up() may change the duration reported from chip. We should
take the real timeout for current channel privilege.
Fixes: 034ae28b56f1 ("wifi: mt76: mt7921: introduce remain_on_channel support")
Signed-off-by: Deren Wu <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use the sts variable when setting vht beamform sts cap.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In newer chipsets, CFEND_RATE setting has been moved to different hw
module.
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This reports signal strength of ACK packets from the peer as measured
at each interface.
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When the chanctx enabled, IEEE80211_CONF_CHANGE_CHANNEL in .config()
would not be called anymore. mt76 cannot control RF channel for monitor.
Add monitor type set-channel flow in .change_chanctx().
Fixes: 41ac53c899bd ("wifi: mt76: mt7921: introduce chanctx support")
Reviewed-by: Sean Wang <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When flash mode is enabled, and the eeprom data in the flash is not for
the current chipset, it'll still be checked valid, and the default
eeprom bin won't be loaded.
(e.g., mt7915 NIC inserted with mt7916 eeprom data in the flash.)
Fix this kind of case by adding chip id into consideration in
mt7915_check_eeprom().
Reported-by: Cheng-Ji Li <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Call mt7915_mcu_set_thermal_protect() through
mt7915_thermal_temp_store() to update firmware trigger/restore temp
directly.
Fixes: 02ee68b95d81 ("mt76: mt7915: add control knobs for thermal throttling")
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This patch includes 2 changes:
1. Firmware expects to disable thermal protect first before
reconfiguring.
2. Separate setting thermal_protect and setting thermal_tx_duty into
different functions. These two firmware commands do not need to send
together.
Fixes: 34b877d972be ("mt76: mt7915: add thermal cooling device support")
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Enable thermal management by default shall not be executed during mcu
init. This causes thermal configuration being reset to the firmware
default settings.
Fixes: 0063b86c9120 ("mt76: mt7915e: Enable thermal management by default")
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When adding WED support, mt76_dma_add_buf was accidentally changed to set
the skip_buf0 flag for tx buffers on the wrong queue descriptor entry.
Additionally, there is a rxwi leak when rx buffer allocation fails.
Fix this and make the code more readable by adding a separate function for
adding rx buffers.
Reported-by: Mikhail Gavrilov <[email protected]>
Tested-by: Mikhail Gavrilov <[email protected]>
Fixes: cd372b8c99c5 ("wifi: mt76: add WED RX support to mt76_dma_{add,get}_buf")
Signed-off-by: Felix Fietkau <[email protected]>
When mt7921_abort_roc is called with dev->mutex held, it can deadlock while
calling cancel_work_sync(&phy->roc_work), because the work function could
be waiting to acquire the mutex.
Fix this by flushing the work before taking the mutex
Reported-by: Mikhail Gavrilov <[email protected]>
Fixes: 034ae28b56f1 ("wifi: mt76: mt7921: introduce remain_on_channel support")
Fixes: 41ac53c899bd ("wifi: mt76: mt7921: introduce chanctx support")
Signed-off-by: Felix Fietkau <[email protected]>
Fixed coverity issue with resource leaks at variable "fw" going out of
scope leaks the storage it points to mt7921_check_offload_capability().
Reported-by: coverity-bot <[email protected]>
Addresses-Coverity-ID: 1527806 ("Resource leaks")
Fixes: 034ae28b56f1 ("wifi: mt76: mt7921: introduce remain_on_channel support")
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Since mt76_dma_rx_fill() acquires mt76_queue spinlock, rely on mt76_queue
page_frag_cache in mt76_dma_rx_fill() instead of wed rx_buf_ring
page_frag_cache. Get rid of mt76_dma_rx_get_frag_cache since it is no
longer used.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Take into account possible error conditions of mt76_rx_token_consume
routine in mt7915_mmio_wed_init_rx_buf() and mt76_dma_add_buf()
Fixes: cd372b8c99c5 ("wifi: mt76: add WED RX support to mt76_dma_{add,get}_buf")
Fixes: 4f831d18d12d ("wifi: mt76: mt7915: enable WED RX support")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Do not increment queue head if mt76_dma_add_buf fails for Wireless
Ethernet Dispatcher rx queues.
Fixes: cd372b8c99c5 ("wifi: mt76: add WED RX support to mt76_dma_{add,get}_buf")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce the capability to support per-phy led blinking. This is needed
for devices supporting dbdc.
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce the capability to support per-phy led blinking. This is needed
for devices supporting dbdc.
Tested-by: Frank Wunderlich <[email protected]>
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move leds struct in mt76_phy in order to have leds associated to phy
(e.g. in dbdc mode) instead of per device.
Tested-by: Frank Wunderlich <[email protected]>
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The default case for frame_contorl is invalid. We should always
assign addr3 of this frame properly.
Coverity error message:
if (ieee80211_has_a4(hdr.frame_control))
(19) Event uninit_use_in_call: Using uninitialized value "hdr".
Field "hdr.addr3" is uninitialized when calling "memcpy".
memcpy(skb_push(skb, sizeof(hdr)), &hdr, sizeof(hdr));
else
memcpy(skb_push(skb, sizeof(hdr) - 6), &hdr, sizeof(hdr) - 6);
Fixes: 0880d40871d1 ("mt76: connac: move mt76_connac2_reverse_frag0_hdr_trans in mt76-connac module")
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In the expression "map[i].qid << 24" starts as u8, but is promoted to
"signed int", then sign-extended to type "unsigned long", which is not
intended. Cast to u32 to avoid the sign extension.
Fixes: 776ec4e77aa6 ("mt76: mt7915: rework debugfs queue info")
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In the expression "map[i].qid << 24" starts as u8, but is promoted to
"signed int", then sign-extended to type "unsigned long", which is not
intended. Cast to u32 to avoid the sign extension.
Reported-by: coverity-bot <[email protected]>
Addresses-Coverity-ID: 1527813 ("Integer handling issues")
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In ACPI enabled devices, mt7921 should read MTFG table from platform
hardware. Apply necessary settings for firmware capabilities through CLC
command.
Co-developed-by: Deren Wu <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Quan Zhou <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
After 'commit ba45841ca5eb ("wifi: mt76: mt76x02: simplify struct
mt76x02_rate_power")', mt76x02 relies on ht[0-7] rate_power data for
vht mcs{0,7}, while it uses vth[0-1] rate_power for vht mcs {8,9}.
Fix a possible out-of-bound access in mt76x0_phy_get_target_power routine.
Fixes: ba45841ca5eb ("wifi: mt76: mt76x02: simplify struct mt76x02_rate_power")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
addr <= MT_CBTOP2_PHY_END(0xffffffff) is always true (<= u32max),
so drop it.
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The mcu event might not be reliable, so check the correctness of data
before handling it.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Check return value of mt7996_mcu_get_eeprom_free_block() first before
accessing free_block_num.
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Check return value of mt7915_mcu_get_eeprom_free_block() first before
accessing free_block_num.
Fixes: bbc1d4154ec1 ("mt76: mt7915: add default calibrated data support")
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The current flow confuses coverity check that leads to false reporting,
so split the offs[] into two pieces according to chipset revision to
silence coverity tool.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This code is supposed to set a u32 value, but casting will not work on
big endian systems.
Reported-by: coverity-bot <[email protected]>
Addresses-Coverity-ID: 1527816 ("Integer handling issues")
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Coverity message:
using tainted "r->band_idx" variable as an index into an array "(*dev).mt76.phys".
Reported-by: coverity-bot <[email protected]>
Addresses-Coverity-ID: 1527812 ("Insecure data handling")
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Coverity message:
using tainted "hdr->band" variable as an index into an array "(*dev).mt76.phys".
Reported-by: coverity-bot <[email protected]>
Addresses-Coverity-ID: 1527797 ("Insecure data handling")
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
SDIO may need addtional 511 bytes to align bus operation. If the tailroom
of this skb is not big enough, we would access invalid memory region.
For low level operation, increase skb size to keep valid memory access in
SDIO host.
Error message:
[69.951] BUG: KASAN: slab-out-of-bounds in sg_copy_buffer+0xe9/0x1a0
[69.951] Read of size 64 at addr ffff88811c9cf000 by task kworker/u16:7/451
[69.951] CPU: 4 PID: 451 Comm: kworker/u16:7 Tainted: G W OE 6.1.0-rc5 #1
[69.951] Workqueue: kvub300c vub300_cmndwork_thread [vub300]
[69.951] Call Trace:
[69.951] <TASK>
[69.952] dump_stack_lvl+0x49/0x63
[69.952] print_report+0x171/0x4a8
[69.952] kasan_report+0xb4/0x130
[69.952] kasan_check_range+0x149/0x1e0
[69.952] memcpy+0x24/0x70
[69.952] sg_copy_buffer+0xe9/0x1a0
[69.952] sg_copy_to_buffer+0x12/0x20
[69.952] __command_write_data.isra.0+0x23c/0xbf0 [vub300]
[69.952] vub300_cmndwork_thread+0x17f3/0x58b0 [vub300]
[69.952] process_one_work+0x7ee/0x1320
[69.952] worker_thread+0x53c/0x1240
[69.952] kthread+0x2b8/0x370
[69.952] ret_from_fork+0x1f/0x30
[69.952] </TASK>
[69.952] Allocated by task 854:
[69.952] kasan_save_stack+0x26/0x50
[69.952] kasan_set_track+0x25/0x30
[69.952] kasan_save_alloc_info+0x1b/0x30
[69.952] __kasan_kmalloc+0x87/0xa0
[69.952] __kmalloc_node_track_caller+0x63/0x150
[69.952] kmalloc_reserve+0x31/0xd0
[69.952] __alloc_skb+0xfc/0x2b0
[69.952] __mt76_mcu_msg_alloc+0xbf/0x230 [mt76]
[69.952] mt76_mcu_send_and_get_msg+0xab/0x110 [mt76]
[69.952] __mt76_mcu_send_firmware.cold+0x94/0x15d [mt76]
[69.952] mt76_connac_mcu_send_ram_firmware+0x415/0x54d [mt76_connac_lib]
[69.952] mt76_connac2_load_ram.cold+0x118/0x4bc [mt76_connac_lib]
[69.952] mt7921_run_firmware.cold+0x2e9/0x405 [mt7921_common]
[69.952] mt7921s_mcu_init+0x45/0x80 [mt7921s]
[69.953] mt7921_init_work+0xe1/0x2a0 [mt7921_common]
[69.953] process_one_work+0x7ee/0x1320
[69.953] worker_thread+0x53c/0x1240
[69.953] kthread+0x2b8/0x370
[69.953] ret_from_fork+0x1f/0x30
[69.953] The buggy address belongs to the object at ffff88811c9ce800
which belongs to the cache kmalloc-2k of size 2048
[69.953] The buggy address is located 0 bytes to the right of
2048-byte region [ffff88811c9ce800, ffff88811c9cf000)
[69.953] Memory state around the buggy address:
[69.953] ffff88811c9cef00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[69.953] ffff88811c9cef80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[69.953] >ffff88811c9cf000: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[69.953] ^
[69.953] ffff88811c9cf080: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[69.953] ffff88811c9cf100: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
Fixes: 764dee47e2c1 ("mt76: sdio: move common code in mt76_sdio module")
Suggested-by: Lorenzo Bianconi <[email protected]>
Tested-by: YN Chen <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add missing of_node_put() after of_reserved_mem_lookup()
Fixes: 99ad32a4ca3a ("mt76: mt7915: add support for MT7986")
Signed-off-by: Wang Yufen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The SPR parameter set comprises OBSS PD threshold for SRG and
non SRG and Bitmap of BSS color and partial BSSID. This adds
support to configure fields of SPR element to firmware.
User can disable firmware SR algorithms by turning sr_scene_detect off.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This reports signal strength of ACK packets from the peer as measured
at each interface.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This adds selectable RTC/CTS enablement for each interface.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Due to information missing, the firmware may be fail on bandwidth
related settings in mt7921/mt7922. Add new cmd STA_REC_HE_V2 to apply
additional capabilities in 6GHz band.
Tested-by: Ben Greear <[email protected]>
Co-developed-by: Deren Wu <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
