Introduce extended utility routines to read/write data o usb bus. New
devices (e.g. mt7663u) will rely on both upper and lower part of the
register address. Add ext parameter to mt76u_init signature in order to
reuse the code adding mt7663u support.
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add mt76u_alloc_mcu_queue utility routine to allocate mcu hw rx queue.
This is a preliminary patch to support new devices (e.g. mt7663u) that
rely on a hw queue for mcu messages
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Resume all possible rx queues after suspend. This is a preliminary patch
to support mt7663u devices
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add mt76_queue parameter to mt76u_rx_urb_alloc signature since this
routine will be used to allocate urbs for mcu hw queue used by new
chipset generation (e.g. mt7663u). Check sg_max_size in in
mt76u_urb_alloc in order to use linear urb for mcu queue
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt76u_alloc_rx_queue routine to allocate rx hw queue.
This is a preliminary patch to support new devices (e.g. mt7663u) that
rely on a hw queue for mcu messages
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Stop/free all configured rx queues (data/mcu) in
mt76u_stop_rx/mt76u_free_rx. This is a preliminary patch to support new
devices (e.g. mt7663u) that rely on a hw queue for mcu messages
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt76u_free_rx_queue utility routine to free rx hw queue.
This is a preliminary patch to support new devices (e.g. mt7663u) that
rely on a hw queue for mcu messages
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mcu buffer allocation in mt76x2u/mt76x0u drivers since newer
chipsets (e.g. mt7663u) does not rely on synchronous mcu communication
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add queue_id parameter to mt76u_submit_rx_buffers in order to reuse it
adding mt7663u support
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In order to reuse mt76u_complete_rx for both data and mcu rx queue, rely
on mt76_queue as urb context in mt76u_complete_rx. Moreover set usb rx
endoint according to rx queue in mt76u_submit_rx_buf. This is a
preliminary patch to add mt7663u support
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt76_queue parameter to mt76u_refill_rx signature in order to
reuse it for mcu hw rx queue
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rely on mt76_queue pointer in mt76u_get_next_rx_entry in order to add
support for new devices (e.g 7663u) that reports fw events through hw rx
mcu queue
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt76u_process_rx_queue routine to process rx hw queue.
This is a preliminary patch to support new devices (e.g. mt7663u) that
rely on a hw queue for mcu messages
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
New devices (e.g. mt7663u) do not rely on stats workqueue to load tx
statistics but will be reported by the firmware. Check tx_status_data
pointer in mt76u_tx_tasklet in order to reuse tx tasklet for new devices
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Starting from 'commit ee8040139ab1 ("mt76: do not overwrite
max_tx_fragments if it has been set")' we can avoid overwriting
max_tx_fragments for mt76x02u devices
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move WIPHY_FLAG_HAS_CHANNEL_SWITCH in mt76-core module since now all
drivers support Channel Switch Announcement
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce dfs radar pattern specs in mt7615 driver in order to make
dfs debugging easier. Radar pulse/pattern thresholds are taken from
vendor SDK.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce token tracing support in mt7615_mac_tx_free routine
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mac_txdone tracepoint in common code in order to
be reused by mt7603 and mt7615 drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move dev_irq tracepoint in common code in order to be reused by mt7603
and mt7615 drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The ring is used for looping back tx powersave filtered frames, so it could
use some more room, in case more than one aggregate was queued
Signed-off-by: Felix Fietkau <[email protected]>
Fixes a theoretical issue where it could potentially overwrite an existing
descriptor entry (and leaking its skb)
Signed-off-by: Felix Fietkau <[email protected]>
Avoids a theoretical corner case where the hardware could try to process
a stale descriptor after a watchdog reset
Signed-off-by: Felix Fietkau <[email protected]>
The hardware does not support using the same MAC address for interfaces,
even if they are on different bands.
In the future this will be made configurable via device tree
Signed-off-by: Felix Fietkau <[email protected]>
Current implementation always use default eeprom mac address to
configure device registers even if it is updated using
mt76_eeprom_override. Fix it initializing macaddr filed of mt76_dev data
structure with eeprom mac address and running mt76_eeprom_override
before mt76x02_mac_setaddr
Fixes: d1bc9bf2072c ("mt76: mt76x0: eeprom: add support for MAC address from OF")
Tested-by: Kevin Schmidt <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
[backported from upstream commit 693d060536abca7b16d2fb8e66aa56be2a2443a2]
Signed-off-by: David Bauer <[email protected]>
No need to send both MCU_EXT_CMD_SET_RX_PATH and MCU_EXT_CMD_CHANNEL_SWITCH
together to MCU.
Split them out by passing the proper command in the corresponding flow.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
MT7615 supports dual-wiphy which means that it can run on 2.4G and 5GHz
channels simultaneously, and driver should configure each band.
Add missing register settings, and refine band related definitions to
avoid duplicate codes.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Even if they are not currently used fix BK/BE endpoint definition order.
Fixes: b40b15e1521f ("mt76: add usb support to mt76 layer")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix the following compilation warning in mt76_eeprom_override routine
when CONFIG_OF is not set and label 'out' is not actually used
drivers/net/wireless/mediatek/mt76/eeprom.c: In function ‘mt76_eeprom_override’:
drivers/net/wireless/mediatek/mt76/eeprom.c:100:1: warning: label ‘out’ defined but not used [-Wunused-label]
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rely on FIELD_PREP macro for led register definitions and
remove open coding
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rely on FIELD_PREP macro for led register definitions and
remove open coding
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Initialize brightness_set and blink_set callbacks to
mt7615_led_set_brightness and mt7615_led_set_blink in order to enable
LED support in mt7615 driver
Tested-by: Deng Qingfang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
We do not call mt76x02_mac_set_beacon() with NULL skb any longer and
we do not need to return error value.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
With current implementation we do not cleanup beacon memory, so is not
needed to call mt76x02_mac_set_beacon() with NULL skb.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
For transferring data over USB the optimal size is endpoint maxpacket.
For my hardware maxpaket for control endpoint is 64 bytes and changing
to this value from 128 bytes further shorten TBTT work time from
3ms to 1ms.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This patch enables channel switch support on mt76 usb interfaces.
Signed-off-by: Markus Theil <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use larger batches for usb copy to speed this operation up. Otherwise it
would be too slow for copying new beacons or broadcast frames over usb.
Assure, that always a multiple of 4 Bytes is copied, as outlined in
850e8f6fbd "mt76: round up length on mt76_wr_copy" from Felix Fietkau.
Signed-off-by: Markus Theil <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
