eeprom.h is mostly empty for mt7921, so get rid of it.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
gen_ppe_thresh routine is shared between mt7615, mt7915, mt7921 and
mt7996 so move it in mt76_connac module.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
sta_ps callback is just an empty stub for most of the drivers,
so get rid of them.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Most of connac based drivers (mt7921, mt7615, mt7663) share the same
code to enable interrupts. Move it in mt76_connac module.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
irq_tasklet struct is used by most of the drivers (e.g. mt7915, mt7921,
mt7615, mt7663 and mt7996) so move it in common code.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The user is allowed to change beacon tx rate (HT/VHT/HE) from hostapd.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Similar to BSS_CHANGED_BASIC_RATES, this enables mcast rate
configuration through fixed rate tables.
Signed-off-by: Ryder Lee <[email protected]>
Change-Id: Ifc305e8c7de9a7df4ad5f856e2097d721a886aaa
Signed-off-by: Felix Fietkau <[email protected]>
The connac3 removes fixed rate fields to reduce txd size and introduces
global rate tables (64 entries) for rate setting. Driver needs to fill
the corresponding idx in MT_TXD6_TX_RATE while tx, and push mt76_rate
into predifined table at bootup stage so that mvif->basic_rates_idx
can immediately switch out once setting changes.
spe_idx is also needed for fixed rate frames, and will be updated by
future patches.
Note that all table entries are shared across driver and firmware
(i.e.TxBF), hence adding MT7996_BASIC_RATES_TBL to reflect mapping
status.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Take nss calculation into account since this function always wrongly
returns 0.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The vif->bss_conf.mcast_rate should be applied to multicast data frame
only.
Fixes: 182071cdd594 ("mt76: connac: move connac2_mac_write_txwi in mt76_connac module")
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
If the chip reset worker is triggered during the remove process, the chip
DMA may not be properly pushed back to the idle state. This can lead to
corruption of the DMA flow due to the chip reset. Therefore, it is
necessary to stop the chip reset before the DMA is finalized.
To avoid resetting the chip after the reset worker is cancelled, use
__mt7921_mcu_drv_pmctrl() instead of mt7921_mcu_drv_pmctrl(). It is safe to
ignore the pm mutex because the pm worker and wake worker have already been
cancelled.
Fixes: 033ae79b3830 ("mt76: mt7921: refactor init.c to be bus independent")
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Co-developed-by: Deren Wu <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Co-developed-by: Wang Zhao <[email protected]>
Signed-off-by: Wang Zhao <[email protected]>
Signed-off-by: Quan Zhou <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The hardware team has advised the driver that it is necessary to first put
WFDMA into an idle state before resetting the WFDMA. Otherwise, the WFDMA
may enter an unknown state where it cannot be polled with the right state
successfully. To ensure that the DMA can work properly while a stressful
cold reboot test was being made, we have reordered the programming sequence
in the driver based on the hardware team's guidance.
The patch would modify the WFDMA disabling flow from
"DMA reset -> disabling DMASHDL -> disabling WFDMA -> polling and waiting
until DMA idle" to "disabling WFDMA -> polling and waiting for DMA idle ->
disabling DMASHDL -> DMA reset.
Where he polling and waiting until WFDMA is idle is coordinated with the
operation of disabling WFDMA. Even while WFDMA is being disabled, it can
still handle Tx/Rx requests. The additional polling allows sufficient time
for WFDMA to process the last T/Rx request. When the idle state of WFDMA is
reached, it is a reliable indication that DMASHDL is also idle to ensure it
is safe to disable it and perform the DMA reset.
Fixes: 0a1059d0f060 ("mt76: mt7921: move mt7921_dma_reset in dma.c")
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Co-developed-by: Deren Wu <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Co-developed-by: Wang Zhao <[email protected]>
Signed-off-by: Wang Zhao <[email protected]>
Signed-off-by: Quan Zhou <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
`mt7921u_dma_init` can only return zero or negative number according to its
definition. When it returns non-zero number, there exists an error and this
function should handle this error rather than return directly.
Fixes: 0d2afe09fad5 ("mt76: mt7921: add mt7921u driver")
Signed-off-by: Jiefeng Li <[email protected]>
Reviewed-by: Dongliang Mu <[email protected]>
Reviewed-by: Sridhar Samudrala <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mcu_uni_event and mcu_reg_event structs are shared between mt7921 and
mt7615 drivers, so move them in connac lib.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Host triggered and catastrophic event triggered firmware core dumping
for basic firmware issues triage, including state reporting, function
calltrace and MCU memory dump.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add testing points into debugfs to trigger firmware assert and enable
full system recovery. Also rename knob "fw_ser" to a clear-cut name
"sys_recovery".
Co-developed-by: Bo Jiao <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add mt7996_reset() and refactor mt7996_mac_reset_work() to support
full system recovery.
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce p2p-go/p2p-client support to mt7921 driver
CONNECTION_P2P_GC/GO is not supported with the current firmware
so we added mt76_dev to mt76_connac_mcu_sta_basic_tlv signature to
use CONNECTION_INFRA_STA/AP instead for p2p-client and p2p-go
respectively to make it work.
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When the BIOS has been configured for Fast Boot, systems with mt7921e
have non-functional wifi. Turning on Fast boot caused both bus master
enable and memory space enable bits in PCI_COMMAND not to get configured.
The mt7921 driver already sets bus master enable, but explicitly check
and set memory access enable as well to fix this problem.
Tested-by: Anson Tsao <[email protected]>
Signed-off-by: Mario Limonciello <[email protected]>
Acked-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
FIF_* flags from mac80211 is not ABI. mt7921 should not pass it into mcu
directly. Remap FIF_* to driver defined flags as mcu command input.
Fixes: c222f77fd421 ("wifi: mt76: mt7921: fix rx filter incorrect by drv/fw inconsistent")
Signed-off-by: Neil Chen <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Since the fw offload capability check is shared between pci,usb and sdio
devices, move it in common init code and reduce code duplication.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Currently using BSS_INFO_PS command will sometimes cause packet drop in
hw rx queue.
Temporarily remove this function until finding the cause.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Init mpdu density based on the hardware capability to prevent rx drop.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix the tail and data pointers. The rxd->len in mt7996_mcu_rxd does not
include the length of general rxd. It only includes the length of
firmware event rxd. Use skb->length to get the correct length.
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Tri-band chipsets support one band on each a-die, so remove the unused
definition of eeprom band selection.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Pass qid into mt7996_mac_write_txwi() to let the tx descriptor of
non-bufferable MMPDUs be filled with correct hw queue index.
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Those capabilities have been added into ieee80211_bss_conf.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Those capabilities have been added into ieee80211_bss_conf.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
According to the documentation, ieee80211_rx_list must not run concurrently
with ieee80211_tx_status (or its variants).
Cc: [email protected]
Fixes: 88046b2c9f6d ("mt76: add support for reporting tx status with skb")
Reported-by: Brian Coverstone <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This helps avoid cleartext leakage of already queued or powersave buffered
packets, when a reassoc triggers the key deletion.
Cc: [email protected]
Signed-off-by: Felix Fietkau <[email protected]>
This fixes the following compile error when compiling against recent
glibc:
------------
/tools/eeprom.c:223:9: error: ignoring return value of 'fread' declared with attribute 'warn_unused_result' [-Werror=unused-result]
223 | fread(buf, 1, EEPROM_PART_SIZE, f);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
------------
Signed-off-by: Hauke Mehrtens <[email protected]>
There's no keep-alive packet being received by mac80211 stack when WED
is enabled, which leads to tx BA session timeout. This patch calls
ieee80211_refresh_tx_agg_session_timer() to refresh timer according
to tx status reporting.
Signed-off-by: Ryder Lee <[email protected]>
Trying to probe a mt7921e pci card without firmware results in a
successful probe where ieee80211_register_hw hasn't been called. When
removing the driver, ieee802111_unregister_hw is called unconditionally
leading to a kernel NULL pointer dereference.
Fix the issue running mt76_unregister_device routine just for registered
hw.
Link: https://bugs.debian.org/1029116
Link: https://bugs.kali.org/view.php?id=8140
Reported-by: Stuart Hayhurst <[email protected]>
Fixes: 1c71e03afe4b ("mt76: mt7921: move mt7921_init_hw in a dedicated work")
Tested-by: Helmut Grohne <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
A number of users reported that this support was working fine before
it got removed. Add it back, but leave out the unsupported 80+80 mode.
Fixes: ac922bd60ace ("wifi: mt76: mt7915: remove BW160 and BW80+80 support")
Signed-off-by: Felix Fietkau <[email protected]>
The scatter and gather frame may be incorrect because WED and WO may
send frames to host driver interleaved.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Sujuan Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
If kernel do not enable CONFIG_HWMON, it may cause thermal
initialization to be done with temperature value 0 and then can not
transmit. This commit fixes it by setting trigger/restore temperature
before checking CONFIG_HWMON.
Fixes: 7d12b38ab6f6 ("wifi: mt76: mt7915: call mt7915_mcu_set_thermal_throttling() only after init_work")
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
