Make sure to run mt7615_mcu_set_roc() holding mt76 mutex in order to
wake the device from low power state and avoid races
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Make sure to run mt7615_mcu_set_wmm() holding mt76 mutex in order to
wake the device from low power state and avoid races
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Make sure to run mt7615_dfs_init_radar_detector in mt7615_regd_notifier
holding mt76 mutex in order to avoid races and set the device in full
power
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Set device in full power before performing hw scan or hw scheduled scan
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Make sure to wake the device in mt7615_pci_suspend in order to properly
configure device registers before suspend
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7615_update_survey utility routine in order to compute
survey stats without waking up the device since it runs holding mt76 lock.
Run mt7615_pm_wake directly in mt7615_update_channel since it can run
with mt76.mutex held if called by mac80211
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce runtime-pm power_save delayed work used to enable
low-power after an inactivity period
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Make sure the device is in full-power before uploading keys to the hw
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Make sure the device is in full-power before reading regs in debugfs
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7615_mutex_{acquire,release} utility routines in order to
switch in full-power/low-power before/after accessing device register-map
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7615_pm_wake utility routine to wake the device from
runtime low-power state (lower-power state is currently supported by
offload firmware for pcie devices).
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76 workqueue from usb to common code in order to be reused adding
low-power support for mt7663 chipset
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
According to the vendor sdk, mt7663 does not need to poll register after
firmware own. Since just mt7622 polls status register, set proper
timeout value according to the vendor sdk
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Avoid memcpy in Rx hot path to slightly improve performance.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Enable support for HC-M7662BU1 module on mt76x2u driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Supports sending a configurable number of packets with a specific rate
and configurable tx power levels / antenna settings, as well as displaying
rx statistics.
Signed-off-by: Felix Fietkau <[email protected]>
This can be used for calibration in the manufacturing process.
It supports sending a configurable number of packets with a specific rate
and configurable tx power levels / antenna settings.
It also supports receiving packets and showing some statistics, including
packet counters and detailed RSSI information.
It will only be compiled in if CONFIG_NL80211_TESTMODE is enabled
Signed-off-by: Felix Fietkau <[email protected]>
All drivers use this in pretty much the same way. Moving it to core helps with
some checks for the upcoming testmode support
Signed-off-by: Felix Fietkau <[email protected]>
Now that the bus access functions can use mapping for accessing full
register addresses, use it for WF_PHY registers to keep them constant.
Needed for follow-up work on testmode support
Signed-off-by: Felix Fietkau <[email protected]>
Unlike on earlier chips, DMA completion on MT7615 does not imply actually
having sent out any packets.
Since AQL will prevent filling the hardware queues and will only allow more
packets to be passed to the driver after tx completion, it makes much more
sense to schedule the tx tasklet there.
This is also needed for scheduling tx in testmode support
Signed-off-by: Felix Fietkau <[email protected]>
Rely on mt76x2e prefix in mt76x2/pci.c and align to the rest of
mt76 code
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Overwrite hw queue id for non-bufferable management frames if the hw/fw
support always txq (altxq) in order to be in sync with mac txwi code
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Since driver no longer handler per-rate tx power setting, we need to
read the power values directly from registers.
Tested-by: Evelyn Tsai <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Clean up the flow of per-rate txpower limit setting to get rid of
dulplicate work since it has already been handled by firmware, and set
proper max_power based on different channels and regdomains.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is easy to add MU EDCA parameters in the future. This patch
also fixes a wrong cw_min assignment.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Enable MU-MIMO DL/UL and add relative counters in debugfs.
Currently MU modules read WTBL first to notify BA changes to
other cross modules, so adjust mt7915_mcu_sta_ba() accordingly.
Tested-by: Evelyn Tsai <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In MT7915, hardware queue map is flexible. However, certain firmware modules
like MU and U-APSD presume a fixed queue order to adapt some devices that have
DMA scheduler with a strict order, so this patch can help in the long run.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Avoid adding MT7615_EEPROM_SIZE twice.
Rename MT7615_EEPROM_EXTRA_DATA to MT7615_EEPROM_FULL_SIZE, since it already
includes MT7615_EEPROM_SIZE
Fixes: ad380ad1ebbe ("mt76: mt7615: add support for applying DC offset calibration from EEPROM")
Signed-off-by: Felix Fietkau <[email protected]>
Introduce U-APSD support in mt76 driver for AP interface
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
For consistency with the rest of the code always rely on defined
macros for register access
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
kernel test robot <[email protected]> found the following issue
and Kalle Valo forwarded it to Linux wireless.
drivers/net/wireless/mediatek/mt76/pci.c:8:6:
warning: no previous prototype for 'mt76_pci_disable_aspm'
Fix this by adding the missing include of mt76.h as Kalle
suggested.
Signed-off-by: Markus Theil <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
While looking at the ETSI regulatory domain definitions
and a patch, which allows more channels for ath10k, I also
checked the channels allowed for mt76.
ETSI regulations would possibly allow to add channels 32, 68,
96, 144, 169 and 173. IEEE 802.11-2016 defines no operating class
for channels 32, 68 and 96. This leaves us channels 144, 169 and 173,
which are included in this patch.
I tested 169 and 173 with a mt76 based USB dongle (AVM AC 860) and they
worked fine. If I saw that right, these channels are also covered by
register definitions inside the driver.
Channel 144 should also work, but gets disabled by the kernel as of now.
Signed-off-by: Markus Theil <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Limits are used to update the channel max_power settings and also passed
to the firmware on channel changes
Signed-off-by: Felix Fietkau <[email protected]>
This subnode can be used to set per-rate tx power limits either per
country code / regdomain or globally.
These limits are typically provided by the device manufacturers and are
used to limit sideband emissions and stay within regulatory limits
Signed-off-by: Felix Fietkau <[email protected]>
Fix up typo in Kconfig with indicating MT7663U is an 802.11ac device
Fixes: eb99cc95c3b6 ("mt76: mt7615: introduce mt7663u support")
Signed-off-by: Sean Wang <[email protected]>
Rely on mt76_for_each_q_rx whenever possible in order to simply the code
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
