After a full chip reset, mac80211 reconfig replays interface, link and
channel context setup. mt7996_vif_link_add() short-circuits when the
link_id is still marked in mvif->valid_links, a state introduced for
postponing link teardown to interface removal. The reset path frees the
link structures without clearing those bits, so the replayed setup never
re-creates dev_info/bss_info/STA records in the restarted firmware and
never re-registers the link wcid, leaving the device inoperative.
The reset path also leaks every allocated MLD index: per-link indices
and the per-vif group/remap indices are re-allocated from scratch during
reconfig, but the old bits stay set in the masks, so repeated full
resets exhaust the index space.
Clear valid_links in the reset vif iterator and reset the MLD index
masks alongside the existing omac_mask clearing.
Fixes: ace5d3b6b49e ("wifi: mt76: mt7996: improve hardware restart reliability")
Fixes: 08813703ac41 ("wifi: mt76: mt7996: Destroy vif active links in mt7996_remove_interface()")
Signed-off-by: Felix Fietkau <[email protected]>
mt7996_mac_reset_vif_iter() queues non-default vif links for kfree_rcu
while dev->wcid[] still holds pointers to the wcid embedded in each
freed link; mt76_reset_device() then dereferences those entries and
runs mt76_wcid_cleanup() on them. If a grace period elapses in between,
the cleanup operates on freed memory.
Run mt76_reset_device() first, so the wcid entries are cleaned up and
cleared while the links are still valid.
Fixes: ace5d3b6b49e ("wifi: mt76: mt7996: improve hardware restart reliability")
Signed-off-by: Felix Fietkau <[email protected]>
WM firmware can enter a partial failure state where RX is hung.
Detect this condition by monitoring SER_PLE_ERR_1 for MDP_RIOC_HANG_ERR
and trigger L1 SER to restore operation. Use transition detection on the
error bit to fire only once per new occurrence, preventing an infinite
SER loop when the bit remains set across checks.
Signed-off-by: Chad Monroe <[email protected]>
Suggested-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt7615_tx() falls back to the vif BSS wcid when mac80211 hands a frame
over without a station, e.g. while a station is being torn down, and to
the global wcid when there is no vif either. Both tx_prepare_skb
implementations derive a mt7615_sta from that wcid unconditionally and,
if the rate control probe flag is set, pass it to mt7615_mac_set_rates(),
which dereferences the NULL vif backpointer of the per-vif embedded sta:
Unable to handle kernel read from unreadable memory at virtual
address 0000000000000002
...
pc : mt7615_mac_set_rates
lr : mt7615_tx_prepare_skb
Neither entry is rate controlled by mac80211: the embedded sta has an
empty rate set, and for the global wcid the container_of does not yield a
valid mt7615_sta at all. Only resolve the sta for wcids that belong to a
station.
Reported-by: Chad Monroe <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When a firmware watchdog triggers full SER recovery before any VAPs
are up, mac80211 skips drv_reconfig_complete() because open_count is
zero. This leaves the DRIVER queue stop reason set permanently,
blocking all TX when interfaces eventually start.
Signed-off-by: Chad Monroe <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The net_setup_tc callback is chosen at compile time and the WED
handler shadows the NPU one when CONFIG_NET_MEDIATEK_SOC_WED is
enabled. mt76_wed_net_setup_tc() returns -EOPNOTSUPP without an
active WED device, so on boards using the Airoha NPU with a WED
enabled kernel the tc offload block is never bound and PPE flow
offload for wireless traffic is silently disabled.
Dispatch on the active offload backend instead: use the WED handler
when a WED device is attached and fall back to the NPU handler
otherwise. Builds without MT76_NPU keep the old behavior through the
mt76_npu_net_setup_tc() stub.
Signed-off-by: Chad Monroe <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move the offload specific parts of Q_READ/Q_WRITE into
mt76_dma_handle_read/write, which return false to fall back to
readl/writel. The WED and NPU #ifdefs now live inside those helpers
instead of selecting between mutually exclusive macro definitions, so a
kernel with both enabled supports both at runtime.
Also fixes the NPU path dereferencing a hardcoded q instead of the macro
argument.
Signed-off-by: Felix Fietkau <[email protected]>
The L1 reset path calls mt76_abort_scan() between setting MT76_MCU_RESET
and waking mcu.wait. A scan work blocked on an in-flight MCU command
does not re-evaluate its wait condition until woken, so the
cancel_delayed_work_sync() inside the abort sleeps out the full MCU
timeout before recovery can proceed, adding several seconds of SER
latency. mt7996_mac_full_reset() and the mt7915 counterpart already
order the wake-up first.
Wake mcu.wait immediately after setting MT76_MCU_RESET so in-flight
commands bail out before the abort synchronises against them.
Fixes: b36d55610215 ("wifi: mt76: abort scan/roc on hw restart")
Signed-off-by: Felix Fietkau <[email protected]>
No hw keys are ever uploaded for scanning/roc links and the link remove
path already skips the key iteration for them. The add path still runs
it, and since mt7996_set_hw_key() resolves the target through
mvif->link[link_id] rather than the offchannel link, starting a scan on
another band re-uploads the group keys of the link sharing the same
link_id, re-sending its BSS cipher info and, for BIGTK with beacon
protection on an AP link, toggling its beacons off and on.
Skip the key iteration for offchannel links, mirroring the remove path.
Fixes: 69d54ce7491d ("wifi: mt76: mt7996: switch to single multi-radio wiphy")
Signed-off-by: Felix Fietkau <[email protected]>
The flow is added to dev->twt_list before sending the agreement to the
firmware, but the error path leaves it linked while flowid_mask is
never set. The flow slot can then be reused and memset while still on
the list, corrupting twt_list, and station removal leaves a dangling
entry behind that mt7915_mac_twt_sched_list_add() later walks.
Fixes: 3782b69d03e7 ("mt76: mt7915: introduce mt7915_mac_add_twt_setup routine")
Signed-off-by: Felix Fietkau <[email protected]>
Because 4 address non-AMSDU packets do not have a bssid field, the
hardware cannot get the bssid. Without the bssid, stations are not
able to leave PS mode due to HW design. Wake up non-setup links when
4-address mode is established to prevent this issue.
mt7992 and mt7990 handle this via the BSSID mapping band config
instead, so restrict the command to mt7996.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When receiving a 4 address non-AMSDU packet, there is no bssid in the
address fields, which breaks powersave handling for 4-address peers.
Set the mcu command to use A1 as bssid when receiving 4 address
non-AMSDU packets on mt7992 and mt7990.
Also skip mt7996_mac_init_band() for invalid bands, so the command is
only sent for bands that actually exist on the device.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The RX path is handled by the WO MCU only on WED v2 hardware. On WED
v3 the same buf1 bit does not carry drop information, so evaluating it
there causes spurious RX drops.
Fixes: e4d2b8bcac11 ("wifi: mt76: drop the incorrect scatter and gather frame")
Signed-off-by: Felix Fietkau <[email protected]>
Add the missing rdd idx check (< 0) in
mt7996_mcu_rdd_background_enable(). mt7996_get_rdd_idx() returns -1
for phys without 5 GHz support, and the negative index was passed to
the RDD MCU command unchecked.
Fixes: 1529e335f93d ("wifi: mt76: mt7996: rework radar HWRDD idx")
Signed-off-by: StanleyYP Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
train_up_high_thres, train_up_rule_rssi and low_traffic_thres were
declared as host-native short in a firmware-facing TLV and assigned
host-order constants, so on a big-endian host the firmware received
byte-swapped rate-adaptation thresholds. Declare them __le16 and convert
with cpu_to_le16().
Fixes: e57b7901469f ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Signed-off-by: Felix Fietkau <[email protected]>
The RX rate decoder set status->nss straight from the PRXV NSTS field,
which for STBC frames is twice the data spatial-stream count. cfg80211
then reported a doubled RX bitrate in station dumps and radiotap. Halve
nss for STBC, matching the TX status path.
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Fixes: d832f5e73815 ("mt76: connac: move mt76_connac2_mac_fill_rx_rate in connac module")
Signed-off-by: Felix Fietkau <[email protected]>
Both drivers cancelled dump_work on unregister but left reset_work and
rc_work to be flushed only by destroy_workqueue() in mt76_free_device(),
which runs after the hw is unregistered and the hardware stopped. A
reset_work that fires in that window calls ieee80211_restart_hw() and
re-arms mac_work on an unregistered hw, and rc_work touches station state
being torn down. Cancel both up front, alongside dump_work.
Fixes: e57b7901469f ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Felix Fietkau <[email protected]>
mt7996_change_vif_links() sets the mld_idx_mask group bit before
allocating the remap index. If the remap allocation fails it jumped to
the exit without clearing that bit, permanently consuming one of the 16
MLD group slots. Release the group bit on the error path.
Fixes: 4fb3b4e7d1ca ("wifi: mt76: mt7996: fix MLD group index assignment")
Signed-off-by: Felix Fietkau <[email protected]>
When a CSA countdown is active, mt7996_mcu_beacon_cntdwn() emits two
bss_bcn_cntdwn_tlv entries (the CSA countdown and the CCA-abort BCC), but
MT7996_BEACON_UPDATE_SIZE only reserved one. With MBSSID enabled and a
near-maximum beacon template the extra 8 bytes could push the offload
command past MT7996_MAX_BSS_OFFLOAD_SIZE and trigger skb_over_panic().
Reserve room for both countdown TLVs.
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Felix Fietkau <[email protected]>
MT_PHY_TYPE_HE_EXT_SU is an enum value (9), not a bit flag, so the
bitwise test "*mode & MT_PHY_TYPE_HE_EXT_SU" also matches OFDM, HT-GF and
several HE/EHT modes. Only genuine ER-SU should be classified as a
106-tone RU at 40 MHz; use an equality comparison.
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Fixes: d832f5e73815 ("mt76: connac: move mt76_connac2_mac_fill_rx_rate in connac module")
Signed-off-by: Felix Fietkau <[email protected]>
The Rx STBC subfield of the VHT capabilities is a 3-bit cumulative value,
but the driver only tested the RXSTBC_1 bit when advertising the peer's
Rx STBC support to firmware. A peer reporting Rx STBC of 2, 3 or 4 has
that bit clear, so STBC was never used towards it. Test the full
IEEE80211_VHT_CAP_RXSTBC_MASK, matching the HT path.
Fixes: 046d2e7c50e3 ("mac80211: prepare sta handling for MLO support")
Fixes: 2660fde82f65 ("wifi: mt76: mt7996: Update mt7996_mcu_add_rate_ctrl to MLO")
Signed-off-by: Felix Fietkau <[email protected]>
mt7996_mac_reset_work() parked the tx worker and disabled the RX/TX NAPIs
before taking dev->mt76.mutex. mt76_worker_disable()/_enable() are plain
kthread park/unpark, not refcounted, and __mt76_set_channel() toggles the
same worker and the MT76_RESET bit under the mutex. An L1 SER racing a
channel switch could therefore have the worker unparked and MT76_RESET
cleared while the reset path resets the DMA rings, corrupting descriptors
or tokens. Take the mutex before disabling the worker, as mt7915 does.
Fixes: 27015b6fbcca ("wifi: mt76: mt7996: enable full system reset support")
Signed-off-by: Felix Fietkau <[email protected]>
When mt76_wcid_alloc() fails, mt7915_add_interface() returned without
clearing the vif_mask/omac_mask bits it had already set, without removing
the firmware dev info added earlier, and without clearing a monitor_vif
pointer to the vif mac80211 is about to free. mac80211 does not call
remove_interface() for a failed add, so the indices and firmware dev
entry leaked permanently and testmode could dereference the stale
monitor_vif. Add a proper error unwind.
Fixes: b619e01380ee ("mt76: fix MBSS index condition in DBDC mode")
Signed-off-by: Felix Fietkau <[email protected]>
mt76_mmio_write_copy() and mt76_mmio_read_copy() iterate up to
ALIGN(len, 4), so a length that is not a multiple of four reads past the
source buffer (write_copy) or writes past the destination (read_copy).
Copy the aligned body in the loop and handle the remaining tail through a
4-byte bounce buffer, keeping the register access width unchanged.
Fixes: 2df00805f7db ("wifi: mt76: mmio_*_copy fix byte order and alignment")
Signed-off-by: Felix Fietkau <[email protected]>
The response TLV loop advanced by tlv->len without a minimum, so a
theoretical firmware response containing a zero-length TLV could spin
forever, hanging the CPU during device probe.
The u32 payload was also read without bounds checking.
Reject a short fixed field, stop on a TLV whose length underruns the
header or overruns the skb.
Fixes: 5d33053be609 ("wifi: mt76: mt7996: add variants support")
Signed-off-by: Felix Fietkau <[email protected]>
sta_rec_he.dcm_rx_max_nss was assigned twice: the second assignment,
sourced from HE PHY capability byte 8 (DCM max RU), overwrote the RX-NSS
value and left dcm_max_ru at zero. Every associated HE station advertising
DCM support was configured in firmware with a wrong dcm_rx_max_nss and a
zero dcm_max_ru. Store the DCM max-RU value in dcm_max_ru as intended.
The same copy-paste error existed in both the shared connac2 path and the
mt7915 path.
Fixes: c336318f57a9 ("mt76: mt7915: add HE capabilities support for peers")
Fixes: 67aa27431c7f ("mt76: mt7921: rely on mt76_connac_mcu common library")
Signed-off-by: Felix Fietkau <[email protected]>
Check the txfree done event DW1 bit 15 when WED is enabled, to avoid
the driver reading a txfree done event before WED has finished reading
it. No need to check this flag on WED v2, otherwise SER will occur.
The bit position was previously defined as MT_DMA_CTL_BURST, which is
unused; rename it to match its function on the txfree ring.
Fixes: 83eafc9251d6 ("wifi: mt76: mt7996: add wed tx support")
Signed-off-by: Rex Lu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
The clock enable path for the second adie sets MT_ADIE_SLP_CTRL_CK0(1)
but polled the busy bit of MT_ADIE_SLP_CTRL_CK0(0), so dual-adie
bring-up could proceed before the adie1 clock was stable.
Fixes: 99ad32a4ca3a ("mt76: mt7915: add support for MT7986")
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
The RXDMAD_C buffers come from the RRO data queues' page pools, which are
bound to a different NAPI, so the direct page-pool recycle used here could
race the owning NAPI; take the non-direct path as is already done for WED
RX queues.
Fixes: e50d4d710efd ("wifi: mt76: Add mt76_dma_get_rxdmad_c_buf utility routione")
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Unlike other WED-RRO queues, RXDMAD_C frames continue into the skb build
path, but mt76_dma_get_buf() skips the desc->info read for RRO queues, so
the uninitialised on-stack info was stored into skb->cb and passed to
rx_skb(); initialise it to zero.
Fixes: e50d4d710efd ("wifi: mt76: Add mt76_dma_get_rxdmad_c_buf utility routione")
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
The TX aggregation check skipped TIDs 6 and 7, so all voice-priority
traffic was sent without a BA session and therefore unaggregated,
limiting throughput for stations that map bulk traffic to VO. The
hardware handles aggregation on the VO queue fine, and a peer that
prefers unaggregated voice frames can still decline the ADDBA request.
Remove the skip from both the connac2 and the mt7996 aggregation setup
paths.
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
A wcid is added to phy->tx_list whenever either tx_pending or
tx_offchannel becomes non-empty, but the requeue check after a partial
schedule required BOTH queues to be non-empty. When
mt76_txq_schedule_pending_wcid() returns -1 (queue stopped or
MT76_RESET) it leaves frames in tx_pending while tx_offchannel is empty,
so the wcid is dropped from every scheduling list and its frames stall
until the next mt76_tx() for that wcid or wcid cleanup. This strands
EAPOL/mgmt/nullfunc frames under momentary queue-full or across
scan/channel-switch, causing association and 4-way-handshake timeouts.
Requeue when either queue still holds frames, matching the enqueue
condition.
Fixes: 0b3be9d1d34e ("wifi: mt76: add separate tx scheduling queue for off-channel tx")
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
The per-chain response-frame RSSI values are packed one per byte, but the
4th chain was extracted with GENMASK(31, 14) instead of GENMASK(31, 24).
The wrong mask overlaps chains 1-3 and shifts by 14, producing a garbage
chain-3 value that corrupts ack_signal/avg_ack_signal on 4x4 radios.
Extract the correct byte.
Fixes: a71b648e3527 ("wifi: mt76: mt7915: add ack signal support")
Fixes: ea5d99d07fbf ("wifi: mt76: mt7996: enable ack signal support")
Fixes: 67fc7a304bf5 ("wifi: mt76: mt7921: add ack signal support")
Fixes: c948b5da6bbe ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
MT_MDP_DCR0_RX_HDR_TRANS_EN is a field of MT_MDP_DCR0, but monitor-mode
handling applied it to the per-band MT_DMA_DCR0 register instead. As a
result RX header translation was never disabled in the MDP when entering
monitor mode, and an undocumented bit of MT_DMA_DCR0 was toggled. Target
MT_MDP_DCR0, matching the mt7996 driver.
Fixes: b2491018587a ("wifi: mt76: mt7915: fix monitor mode issues")
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
mt7996_sta_statistics() set NL80211_STA_INFO_TX_BITRATE unconditionally
after the block that already sets it, so a station with no rate info yet
was reported to userspace with a valid-but-zero TX rate. Drop the
redundant unconditional assignments; the in-block ones are sufficient.
Fixes: b34f346b917e ("wifi: mt76: mt7996: drop return in mt7996_sta_statistics")
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
If a peer's VHT/HE MCS map has no supported spatial stream (all fields
0x3), the loop exits with nss == 0 and the function returned (u8)-1 (255),
which was then written into the firmware sta_rec_bf beamforming fields.
Clamp the result to 0.
Fixes: 89029a85482c ("mt76: mt7915: add Tx beamformer support")
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
mt7915_remove_interface() cleared the wcid mask bit with no lock held and
before clearing the RCU wcid pointer. The mask is a non-atomic RMW shared
with the allocators, which all run under dev->mt76.mutex; on DBDC the two
wiphys share one mt76_dev, so this raced add_interface/sta_add on the
other band and could leak or double-hand-out a wcid. Clearing the bit
before the RCU pointer also let a concurrent allocation reuse the index
and publish its wcid, which the subsequent NULL assignment then wiped.
Move the clear into the existing mutex section, after the RCU pointer is
cleared.
Fixes: f3049b88b2b3 ("wifi: mt76: mt7915: allocate vif wcid in the same range as stations")
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
mt7996_mac_full_reset() called wake_up(&dev->mt76.mcu.wait) without first
setting MT76_MCU_RESET. The MCU response wait condition only checks the
response queue and that bit, so the wake-up released nobody: a thread
blocked in an MCU command against the dead firmware (typically holding
dev->mt76.mutex) stayed asleep until its multi-second timeout, stalling
recovery. Set the bit before the wake-up, as mt7915 does.
Fixes: 27015b6fbcca ("wifi: mt76: mt7996: enable full system reset support")
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
band_idx comes from a 2-bit descriptor field (0-3) and was used directly
to index dev->mt76.phys[] (size __MT_MAX_BAND == 3) and dereference the
result. A corrupt or reserved descriptor value could index out of bounds
or hit a NULL phy on parts with fewer bands. Reject invalid band indices,
mirroring mt7996_rx_get_wcid().
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
The link_id in info->control.flags is required by mt7996 to select the
correct mt76_wcid for transmission.
Not assigning the link_id in info->control.flags is equivalent to
assigning the link_id to 0, causing mt7996 to select link_id 0 for
transmission, so probe requests sent on behalf of an MLD vif scanning
via a different link were transmitted with the wrong per-link wcid.
Fixes: 31083e38548f ("wifi: mt76: add code for emulating hardware scanning")
Signed-off-by: Michael-CY Lee <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
__mt76_tx_queue_skb() overrides the wcid passed by the driver with
sta->drv_priv, so the wcid might incorrectly be changed after TX,
causing wcid->non_aql_packets to be counted on the wrong wcid. For
example, on the AP side, if a station's setup link is the 5G link and
the station uses 2G to transmit a frame, the value of non_aql_packets
is increased on the 5G wcid but decreased on the 2G wcid. Once the
inflated counter exceeds MT_MAX_NON_AQL_PKT, the TX scheduler
permanently refuses to service the station.
Drop the reassignment and account on the wcid used for transmission.
This also records the actual wcid in the queue entry.
Fixes: e1378e5228aa ("mt76: rely on AQL for burst size limits on tx queueing")
Signed-off-by: Michael-CY Lee <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Problem:
MCU command timeout while the firmware state is normal, and the
firmware keeps showing the error log "ERROR!! NO PAUSE...".
Root cause:
If the MLD_ID field in the TXD is neither the primary link id nor the
secondary link id, it may lead to a firmware busy loop when the third
link is in power saving mode.
Remap frames directed to a third link to the primary link wcid. Since
TX status events and txfree completions carry the wcid the firmware
saw, use the remapped wcid for packet id tracking and non-AQL packet
accounting as well, while the frame keeps its original link context
for addressing, band and OMAC selection.
Fixes: 85cd5534a3f2 ("wifi: mt76: mt7996: use correct link_id when filling TXD and TXP")
Signed-off-by: Peter Chiu <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
For RRO 3.0, RX data released from a RRO data queue should be put to
the indicator queue. The frames are processed and completed in the
context of the indicator queue NAPI, which only polls skbs queued on
the MT_RXQ_RRO_IND list; frames queued under the data queue id are
left sitting on that list until the data queue NAPI happens to run,
stalling and reordering RX data.
Fixes: b1e58e137b61 ("wifi: mt76: mt7996: Introduce RRO MSDU callbacks")
Signed-off-by: Rex Lu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
The allocator advances the mask pointer by min / 32 words but computes
the returned index relative to the shifted base, while the size bound
check treats the same value as absolute. For the WED WDS range
(min 256, size 272), a free slot at absolute index 256 + n marked bit
256 + n in the mask but returned n, colliding with regular WTBL
entries, and the relative bound check allowed scanning far beyond the
requested range.
Keep the word offset in the loop index instead of shifting the mask
pointer, so marking, return value and bound check all use absolute
indices.
Signed-off-by: Felix Fietkau <[email protected]>
According to the definition in IEEE Std 802.11be-2024, Table 9-417r:
- If 80 MHz is not supported, bit 1-3 are set to 0.
- If 160 MHz is not supported, bit 2-3 are set to 0.
- If 320 MHz is not supported, bit 3 is set to 0.
Fixes: 348533eb968d ("wifi: mt76: mt7996: add EHT capability init")
Signed-off-by: Shayne Chen <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Introduce regulatory wiphy self-managed mode support for MT7921,
allowing the driver to manage its own regulatory domain independently
from the kernel's regulatory framework.
Signed-off-by: Charlie-cy Wu <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Introduce regulatory wiphy self-managed mode support for MT7925,
allowing the driver to manage its own regulatory domain independently
from the kernel's regulatory framework.
Signed-off-by: Charlie-cy Wu <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Split mt7921_mcu_regd_update() into two functions to prevent recursive
mutex acquisition. Introduce __mt7921_mcu_regd_update() as the internal
implementation that assumes the mutex is already held by the caller,
while mt7921_mcu_regd_update() remains as the external interface that
handles mutex acquisition and release.
This fixes a deadlock issue when mt7921_regd_set_6ghz_power_type() is
called with the device mutex already held. Without this change, calling
mt7921_mcu_regd_update() would attempt to acquire the same mutex again,
causing a recursive lock deadlock.
The __mt7921_mcu_regd_update() function can be safely called when the
caller has already acquired the device mutex, avoiding the deadlock
while maintaining proper synchronization for regulatory domain updates.
Fixes: dc2608cf5224 ("wifi: mt76: mt7921: refactor regulatory notifier flow")
Signed-off-by: Charlie-cy Wu <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
When tx_prepare_skb() returns an error in the SDIO TX path, the
skb is not freed, leading to a memory leak. This can occur when
zero-length frames (such as WNM NULL frames) are dropped to prevent
potential hardware TX hangs.
Fix this by properly releasing the skb with ieee80211_tx_status_ext()
when tx_prepare_skb() fails.
Fixes: b747fa343817 ("mt76: mt7915: drop zero-length packet to avoid Tx hang")
Signed-off-by: Eason Lai <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
The mt7925_tx_power_limit_tlv struct begins with a 4-byte rsv[] field
that acts as a UNI command header prefix. The firmware dispatcher did
not use the 4-byte rsv[] and will only check the payloads after the
4-byte rsv[] As a result, the total message length minus the 4-byte
prefix. Fix this by setting len to msg_len - 4.
Fixes: ccb1863 ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Signed-off-by: Jared.Huang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Felix Fietkau