Introduce wifi LED switch control, add flow to Control a wifi
gpio pin based on the status of WIFI radio, if the pin is connected
to an LED, the LED will indicate the status of the WiFi radio.
Signed-off-by: Hao Zhang <[email protected]>
Co-developed-by: Quan Zhou <[email protected]>
Signed-off-by: Quan Zhou <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The firmware support for management frame protection has limitations:
- do not support cipher BIP-GMAC-128 and BIP-GMAC-256
- support cipher BIP-CMAC-128 and BIP-CMAC-256, except action frame with
action type 'not robust'.
Therefore, to simplify the logic, do not set the IGTK to firmware and
let the encryption of management frames be handled by upper layer.
Signed-off-by: Michael-CY Lee <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The implementation amounts to setting the driver flag
IEEE80211_VIF_SUPPORTS_CQM_RSSI, and then providing
mechanisms for continuously updating enough information
to be able to provide notifications to userspace when
RSSI drops below a certain threshold
Signed-off-by: Rong Yan <[email protected]>
Signed-off-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is expected by the firmware of older chipsets as well, though it may
not have been as strongly required as on mt799x
Fixes: 098428c400ff ("wifi: mt76: connac: set correct muar_idx for mt799x chipsets")
Signed-off-by: Felix Fietkau <[email protected]>
Check if background radar is enabled or not before manually triggering it,
and also add more checks in radar detected event.
Signed-off-by: StanleyYP Wang <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
For mt7992 chipsets, critical packet mode should be properly configured
to let the HW SDO module correctly fill the AC queue in TX descriptors of
some higher priority packets such as ARP and ICMP.
Without this patch, HW queues may hang when running MU traffic.
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Without this commit, reading chip temperature will cause memory leakage.
Fixes: 6879b2e94172 ("wifi: mt76: mt7996: add thermal sensor device support")
Reported-by: Ryder Lee <[email protected]>
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Do not add UNI_BSS_INFO_11V_MBSSID tag when bssid_indicator is not set
to avoid abnormal beaconing behavior in non-11v MBSS scenario.
Signed-off-by: Henry Yen <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
For mt7996 chipsets, the HW CSO module can help to identify TCP traffic,
which assists the firmware in adjusting algorithms to improve overall
performance.
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Set RCPI values in mt7996_mcu_sta_rate_ctrl_tlv(), which can make the
FW rate control algorithm be initialized with a better MCS selection
table.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Set peer address and aid for the BMC wtbl of station interface. For some
functions such as parsing MU_EDCA parameters from beacon, firmware will
need the peer address to do correct parsing.
Without this patch, MU uplink traffic would get suffered.
Reported-by: Howard Hsu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When a BMC wtbl of station interface is correctly set with peer address,
HW will do rx header translation for broadcast data packets, which makes
mac80211 unable to find the corresponding ieee80211_sta and drop the
packets. To fix this, disable HW rx header translation for BMC entry.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
of_gpio.h is deprecated and subject to remove.
The driver doesn't use it, simply remove the unused header.
Signed-off-by: Andy Shevchenko <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Even if it is not a real issue at the moment since concurrent access to
mcu message queue is protected by mcu mutex, make the code more robust
and move mcu queue free space check inside queue spinlock critical section.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Set intr1 to 0 in mt7996_irq_tasklet() in order to avoid possible
uninitialized variable usage if wed is not active for hif2.
Fixes: 83eafc9251d6 ("wifi: mt76: mt7996: add wed tx support")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Before sending suspend & wow command to FW, its length should be
4-bytes alignd.
Signed-off-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
During chip recovery (e.g. chip reset), there is a possible situation that
kernel worker reset_work is holding the lock and waiting for kernel thread
stat_worker to be parked, while stat_worker is waiting for the release of
the same lock.
It causes a deadlock resulting in the dumping of hung tasks messages and
possible rebooting of the device.
This patch prevents the execution of stat_worker during the chip recovery.
Signed-off-by: Leon Yen <[email protected]>
Signed-off-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt7920e is a mt7921 series chipset with 802.11ax 2x2:2SS support.
The major difference is in firmware side only, at this moment.
This patch would add some mandatory changes for new chip id and
firmware download control.
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fixes issues with scanning and low power output at some rates.
Fixes: f75e4779d215 ("wifi: mt76: mt7996: add txpower setting support")
Signed-off-by: Chad Monroe <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The wcid can be NULL. It should be checked for validity before
dereferencing it to avoid crash.
Fixes: 098428c400ff ("wifi: mt76: connac: set correct muar_idx for mt799x chipsets")
Signed-off-by: Muhammad Usama Anjum <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix the following sparse warnings:
drivers/net/wireless/mediatek/mt76/mt7915/debugfs.c:1133:29: error: too long token expansion
drivers/net/wireless/mediatek/mt76/mt7915/debugfs.c:1133:29: error: too long token expansion
drivers/net/wireless/mediatek/mt76/mt7915/debugfs.c:1133:29: error: too long token expansion
drivers/net/wireless/mediatek/mt76/mt7915/debugfs.c:1133:29: error: too long token expansion
No functional changes, compile tested only.
Fixes: e3296759f347 ("wifi: mt76: mt7915: enable per bandwidth power limit support")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Acked-by: Felix Fietkau <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Link: https://msgid.link/5457b92e41909dd75ab3db7a0e9ec372b917a386.1710858172.git.lorenzo@kernel.org
This flag is needed for the PSE client reset. Fixes watchdog reset issues.
Fixes: c677dda16523 ("wifi: mt76: mt7603: improve watchdog reset reliablity")
Signed-off-by: Felix Fietkau <[email protected]>
Use the correct WMM AC queue instead of the MGMT one to fix potential issues
with aggregation sequence number tracking. Drop non-bufferable packets.
Fixes: fca9615f1a43 ("mt76: mt7603: fix up hardware queue index for PS filtered packets")
Signed-off-by: Felix Fietkau <[email protected]>
When pre-calibration data is missing, do not fail the driver probe.
Instead, just print a warning and fall back to regular calibration.
Signed-off-by: Felix Fietkau <[email protected]>
Add pre-calibration for mt7986 and mt7916. It has different data size
with mt7915. Group cal needs 54k and 94k for 2G + 5G and 2G + 6G,
respectively. DPD cal needs 300k.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: StanleyYP Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Send an update to the MCU whenever the settings change
Signed-off-by: MeiChia Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Set correct beamformer capabilities for station vif in HE PHY
capabilities IE.
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Do not report measurements if the airtime counter was cleared since the
last update (possibly by firmware)
Signed-off-by: Henry Yen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The mcu command format are different for mt7915 and mt7986.
Fix the mt7915_mcu_wed_wa_tx_stats to support mt7915 and mt7986.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When queueing packets, only the MT76_RESET flag of the primary PHY
is checked. If the primary PHY is scanning or changing channels, this can
lead to packet loss for tx on the second PHY.
Fix this by passing the phy to the .tx_queue_skb op and using it to check
the correct flag.
Signed-off-by: Felix Fietkau <[email protected]>
The variable tidno is being assigned a value that is not being read
and is being re-assigned a new value a few statements later.
The assignment is redundant and can be removed.
Cleans up clang scan warning:
drivers/net/wireless/mediatek/mt76/agg-rx.c:125:5: warning: Value stored
to 'tidno' during its initialization is never read [deadcode.DeadStores]
Signed-off-by: Colin Ian King <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Because the number of channels to be configured is calculated using the %,
and it results in 0 when there's an exact division, this leads to some
channels not having their tx power configured.
Fixes: 7801da338856 ("wifi: mt76: mt7921: enable set txpower for UNII-4")
Signed-off-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
MediaTek's controller driver on COB platform (e.g. MT8188) is
capable of controlling power supplies and reset pin of a component
(e.g. a WIFI chip) in power-on and power-off process.
Due to this optional feature, mt76 need to inform controller
that mt76 need to keep power during suspend. Otherwise WIFI will be
powered off when system enters suspend process.
The "wakeup-source" property was used for the device that need
this to go into suspend mode so that mt76 suspend handler doesn't
fail and the system is able to enter into a suspend state.
An example:
wifi: mt7921@0 {
wifi0{
reg = <0x0000 0 0 0 0>;
wakeup-source;
};
};
Signed-off-by: Michael Lo <[email protected]>
Signed-off-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In multi-channel scenarios, the granted channel must be aborted before
suspending. Otherwise, the firmware will be put into a wrong state,
resulting in an association failure after resuming.
With this patch, the granted channel will be aborted before suspending
if necessary.
Signed-off-by: Leon Yen <[email protected]>
Signed-off-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Before entering suspend, we need to ensure that all MCU command are
completed. In some cases, such as with regd_notifier, there is a
chance that CLC commands, will be executed before suspend.
Signed-off-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Leon Yen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This patch updates the EU country list to ensure the MTCL table
works correctly.
Signed-off-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Leon Yen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In some case, the MTCL table will exist, but MTDS table will not.
So the SAR will init fail. This patch make MTCL and MTDS can exist
with no dependence.
Fixes: f965333e491e ("mt76: mt7921: introduce ACPI SAR support")
Signed-off-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Leon Yen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
From commit a304e1b82808 ("[PATCH] Debug shared irqs"), there is a test
to make sure the shared irq handler should be able to handle the unexpected
event after deregistration. For this case, let's apply MT76_REMOVED flag to
indicate the device was removed and do not run into the resource access
anymore.
Fixes: c948b5da6bbe ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
