move scanning check from mt76_connac_power_save_sched routine
to mt7921_pm_power_save_work/mt7615_pm_power_save_work ones
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove useless MT76_STATE_PM check in mt7921_mac_work since
mt7921_mutex_acquire will wake up the device if necessary
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Get rid of MT76_STATE_PM chec in mt7615_mac_tx_free and
mt7921_mac_tx_free since we already rely on mt76_connac_pm_unref in the
NAPI callback.
Remove mt76_connac_power_save_sched calls in mt7615_mac_tx_free and
mt7921_mac_tx_free
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In order to avoid synchronization races between tx and rx path, rely on
mt76_connac_skip_fw_pmctrl putting the chip in sleep mode for mt7921 and
mt7663 devices
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In order to avoid synchronization issues between wake and ps works,
cancel ps_work in mt76_connac_pm_wake routine
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7615_poll_rx rx napi callback for mt7663.
Do not access device registers in tx/rx napi if the device is not awake.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7921_poll_rx rx napi callback for mt7921.
Do not access device registers in tx/rx napi if the device is not awake.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add the capability to define a custom rx napi callback for each driver.
This is a preliminary patch to properly support runtime-pm on rx side
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7615_tx_worker routine as mt76 tx worker callback for
mt7663.
Rely on mt76_connac_pm_ref/mt76_connac_pm_unref to check PM state and
increment/decrement wake counter
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7921_tx_worker routine as mt76 tx worker callback for
mt7921.
Rely on mt76_connac_pm_ref/mt76_connac_pm_unref to check PM state and
increment/decrement wake counter
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce wake counter and related spinlock in order to synchronize
tx/rx path and fw_pmctrl request.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce a mutex in order to avoid a race between mt7615_mcu_lp_drv_pmctrl and
mt7615_mcu_fw_pmctrl routines since they are run two independent works
Fixes: 1f549009b5b2 ("mt76: mt7615: do not request {driver,fw}_own if already granted")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce a mutex in order to avoid a race between mt7921_mcu_drv_pmctrl and
mt7921_mcu_fw_pmctrl routines since they are run two independent works
Fixes: 1d8efc741df8 ("mt76: mt7921: introduce Runtime PM support")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Get rid of leftover mt7921_mcu_add_bss_info routine declaration
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_connac_mcu_update_arp_filter in mt76_connac module since the
code is shared between mt7615 and mt7921
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix the following sparse warning:
drivers/net/wireless/mediatek/mt76/mt7921/mac.c:1425:70:
warning: Using plain integer as NULL pointer
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Junlin Yang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
In order to avoid memory leaks, clean the dma engine unloading the
module
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Since driver no longer handler per-rate tx power setting, we need to
read the power values directly from registers.
Tested-by: Evelyn Tsai <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Clean up the flow of per-rate txpower limit setting to get rid of
duplicate work since it has already been handled by firmware, and set
proper max_power based on different channels and regdomains.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Scan abort should be required for the uncompleted hardware scan
interrupted by wifi reset. Otherwise, it is possible that the scan
request after wifi reset gets error code -EBUSY from mac80211 and
then blocks the reconnectting to the access point.
Fixes: 215bb6737bef ("mt76: mt7921: add wifi reset support")
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce chip_reset knob in mt7921 debugfs to export a way to users
able to trigger wifi reset, and group the similar operations
previously defined in chip_config in the same knob.
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Wake the chip before configuring the mcu log level
Fixes: 1d8efc741df8 ("mt76: mt7921: introduce Runtime PM support")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Dump mcu command code in hex and related prefix to help debugging
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Get rid of init work since firmware loading is already performed in
mt7921_init_hardware
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When the EEPROM data is read from flash, it can contain pre-calibration
data, which can save calibration time.
Note that group_cal can save 30% bootup calibration time, and dpd_cal can
save 75% channel switching time.
Tested-by: Bo Jiao <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
For MT7663, the availability of the patch files is used to detect, which
corresponding firmware is going to be used (AP firmware or STA offload
firmware). If the ROM patch was already applied, it could attempt to
load the wrong firmware (without considering the alternative).
Signed-off-by: Felix Fietkau <[email protected]>
MT7663 uses different bits for communicating reset commands/status between MCU
and host. Also add an extra initial reset command.
Signed-off-by: Felix Fietkau <[email protected]>
After DMA reset, tx status information for queued frames will never arrive.
Flush the queue to free skbs immediately instead of waiting for a timeout
Signed-off-by: Felix Fietkau <[email protected]>
We should use ieee80211_free_txskb() to report skb status avoid wrong
aql accounting after reset.
Cc: [email protected]
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In mt7615_mac_reset_work(), make sure freeing skbs after mt7615_dma_reset().
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In mt7915_mac_reset_work(), make sure freeing skbs after mt7915_dma_reset().
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt7915_tx_token_put() should get call before mt76_free_pending_txwi().
Fixes: f285dfb98562 ("mt76: mt7915: reset token when mac_reset happens")
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt7615_tx_token_put() should get call before mt76_free_pending_txwi().
Fixes: a6275e934605 ("mt76: mt7615: reset token when mac_reset happens")
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix ofdm rate index and ldpc setting in rate setting field of tx
descriptor.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rework mt7915_tm_set_tx_len() with mt76_testmode_alloc_skb() to support
larger packet based on a longer tx_time.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add support to send larger packet in testmode to meet requirements
of some test cases.
The limit of max packet size is determined based on tx rate mode setting.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Report trace event related to MCU_EVENT_LP_INFO that is sent by the mcu
when it is ready to enter in deep sleep state
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Ensures that header translation is disabled for interfaces that do not support
it.
Fixes: bb1262e7199b ("mt76: mt7615: add support for rx decapsulation offload")
Signed-off-by: Felix Fietkau <[email protected]>
Resolve the following checkpatch.pl script warning:
WARNING: Missing or malformed SPDX-License-Identifier tag in line 1
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add mmio.c in order to use mt76_bus_ops throughout the driver.
It will be also shared with the future APSoC revision.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Frame reception timestamp (low 32-bits) that indicates the value of the
local TSF timer value at the time the first bit of the MAC header in the
received frame (PPDU unit) arriving at the MAC.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Reduce the data latency during hw_scan by the split scan which would switch
back to operational channel right after scanning each channel done.
Suggested-by: Asda Wen <[email protected]>
Suggested-by: Soul Huang <[email protected]>
Co-developed-by: YN Chen <[email protected]>
Signed-off-by: YN Chen <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use mt76_wr to directly access MT_PCIE_MAC_INT_ENABLE because we used the
remapped address 0x10000 as the base to operate PCIe interrupt.
Fixes: c7b646385a3f ("mt76: mt7921: add wifi reset support")
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix the second insert module causing the device hangs after remove module.
Fixes: 1c099ab44727 ("mt76: mt7921: add MCU support")
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
