Bufferable management frames need to be put in the data queue, otherwise
they will not be buffered when the receiver is asleep.
Signed-off-by: Felix Fietkau <[email protected]>
The hardware expects MT_TX_RATE_NSS to be filled with the number of
space/time streams. For non-STBC rates, this is equal to nss.
For 1-stream STBC, this needs to be set to 2.
This is relevant for VHT rates only, on HT, the value is derived from MCS
internally.
Signed-off-by: Felix Fietkau <[email protected]>
Do not convert {tx,rx}_mcs_map to little-endian since it is already done
by mac80211. This patch fix the following sparse warning:
drivers/net/wireless/mediatek/mt76/mt7615/mcu.c:1497:25: sparse:
warning: cast from restricted __le16
drivers/net/wireless/mediatek/mt76/mt7615/mcu.c:1499:25: sparse:
warning: cast from restricted __le16
Fixes: 04b8e65922f6 ("mt76: add mac80211 driver for MT7615 PCIe-based chipsets")
Fixes: 3ca0a6f6e9df ("mt7615: mcu: use standard signature for mt7615_mcu_msg_send")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix the following sparse warning in mt7603_mcu_set_eeprom:
drivers/net/wireless/mediatek/mt76/mt7603/mcu.c:376:30: sparse: warning:
incorrect type in assignment (different base types)
drivers/net/wireless/mediatek/mt76/mt7603/mcu.c:376:30: sparse:
expected unsigned short [usertype] addr
drivers/net/wireless/mediatek/mt76/mt7603/mcu.c:376:30: sparse: got
restricted __le16 [usertype]
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix the following sparse warning in mt7615_mcu_bss_info_ext_header:
drivers/net/wireless/mediatek/mt76/mt7615/mcu.c:728:30: sparse: sparse:
incorrect type in assignment (different base types)
drivers/net/wireless/mediatek/mt76/mt7615/mcu.c:728:30: sparse:
expected restricted __le32 [usertype] mbss_tsf_offset
Reported-by: kbuild test robot <[email protected]>
Fixes: 04b8e65922f6 ("mt76: add mac80211 driver for MT7615 PCIe-based chipsets")
Fixes: 7339fbc0caa5 ("mt7615: mcu: do not use function pointers whenever possible")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add mt7615_mcu_send_ram_firmware routine since mt7615_load_ram runs the
same code to send ram firmware to cr4 and n9 mcus. Moreover rename
gen_dl_mode in mt7615_mcu_gen_dl_mode.
This patch does not introduce any behaviour change, it is just code
refactor.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Release patch semaphore even if request_firmware fails in
mt7615_load_patch
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix typo setting urb->transfer_buffer_length in mt76u_fill_rx_sg
Fixes: b40b15e1521f ("mt76: add usb support to mt76 layer")
Fixes: f8f527b16db5 ("mt76: usb: use EP max packet aligned buffer sizes for rx")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Instead of use several 4 bytes usb requests, use full 32 bytes buffer
to copy data to device. With the change we use less requests and copy
exact data size to the device regardless size is multiple of 4 or not.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Compiler give us guaranties on variables alignment, so use
an variable as buffer when read/write registers and remove
unneeded {put,get}_unaligned.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In contrast to mt76_wr() which we use to program registers,
on mt76_wr_copy() we should not change endian of the data.
Fixes: b40b15e1521f ("mt76: add usb support to mt76 layer")
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
- Store the previous and current rate set in the driver + the TSF value
at the time of the switch.
- Use the tx status TSF value to determine which rate set needs to be used
as reference.
- Report only short or long GI rates for a single status event, not a mix.
- The hardware reports the last used rate index. Use it along with the
retry count to figure out what rate was used for the first attempt.
- Use the same retry count value for all rate slots to make this calculation
work.
- Derive the probe rate from the current rateset instead of the skb cb
- Do not wait for a status report for the probe frame before removing the
probe rate from the rate table. Do it immediately after it was referenced
in a tx status report.
- Use the first half of the first rate retry budget for the probe rate
in order to avoid using too many retries on that rate
- Switch from lower rates to higher rates more conservatively
- enable hardware rate up/down selection
Signed-off-by: Felix Fietkau <[email protected]>
These values must be initialized to zero, otherwise the hardware could
reuse previous values, especially the rate index
Signed-off-by: Felix Fietkau <[email protected]>
Since we don't clean that tx queue from the tx tasklet, we need to do it
after the firmware upload is done. This patch also adds a cleanup step during
the upload, to help reclaim memory faster.
Fixes unprocessed queued frames eating up memory long after the firmware
upload has already completed
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7615_mcu_rdd_send_pattern routine to trigger a radar pattern
detection. Moreover move debugfs related routines in a dedicated source
file.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add Channel Switch Announcement support to mt7615 driver updating beacon
template with CSA IE received from mac80211
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Delay channel calibration after Channel Availability Check. Add some
code cleanup to mt7615_mcu_set_channel
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add hw radar detection support to mt7615 driver in order to
unlock dfs channels on 5GHz band
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7615_regd_notifier callback. This is a preliminary patch to
add radar detection support to mt7615 driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When beacon length is not a multiple of 4, the beacon could be sent with
the last 1-3 bytes corrupted. The skb data is guaranteed to have enough
room for reading beyond the end, because it is always followed by
skb_shared_info, so rounding up is safe.
All other callers of mt76_wr_copy have multiple-of-4 length already.
Cc: [email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Commit f8f527b16db5 ("mt76: usb: use EP max packet aligned buffer sizes
for rx") breaks A-MSDU support. When A-MSDU is enable the device can
receive frames up to q->buf_size but they will be discarded in
mt76u_process_rx_entry since there is no enough room for
skb_shared_info. Fix the issue reallocating the skb and copying in the
linear area the first 128B of the received frames and in the frag_list
the remaining part
Fixes: f8f527b16db5 ("mt76: usb: use EP max packet aligned buffer sizes for rx")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Remove {out,in}_max_packet from mt76_usb data structure since
they just track last usb endpoint and they are not actually used
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move dfs region field in mt76_dev data structure since it is
used by all drivers. This is a preliminary patch to add DFS support to
mt7615 driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Simplify mt7615_set_channel signature removing cfg80211_chan_def
parameter since it is not actually used
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Reduce rx memory footprint allocating just one SG buffer since for the
moment we support just 3839B as maximal size of an A-MSDU.
Introduce different SG_MAX_SIZE definitions for TX and RX sides.
Moreover set q->buf_size to PAGE_SIZE even for SG case.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This makes sure that the driver update peer's bssid when state
transition occurs.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix wrong settings that will drop packets due to hardware's RX table
searching flow.
Fixes: f072c7ba21 ("mt76: mt7615: enable support for mesh")
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix following sparse warnings in mt76x02_usb_core.c
drivers/net/wireless/mediatek/mt76/mt76x02_usb_core.c:29:6: warning:
symbol 'mt76x02u_tx_complete_skb' was not declared. Should it be static?
drivers/net/wireless/mediatek/mt76/mt76x02_usb_core.c:37:5: warning:
symbol 'mt76x02u_skb_dma_info' was not declared. Should it be static?
drivers/net/wireless/mediatek/mt76/mt76x02_usb_core.c:96:52: warning:
restricted __le16 degrades to integer
drivers/net/wireless/mediatek/mt76/mt76x02_usb_core.c:74:5: warning:
symbol 'mt76x02u_tx_prepare_skb' was not declared. Should it be static?
drivers/net/wireless/mediatek/mt76/mt76x02_usb_core.c:244:6: warning:
symbol 'mt76x02u_init_beacon_config' was not declared. Should it be
static?
drivers/net/wireless/mediatek/mt76/mt76x02_usb_core.c:262:6: warning:
symbol 'mt76x02u_exit_beacon_config' was not declared. Should it be
static?
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When TSSI calibration is disabled (which it means the device has been
equipped with an external power amplifier) we need to refer to
different eeprom fields in order to properly configure tx power
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Set per-channel target power as the minimum between the regulatory
tx power and the value configured in the eeprom
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move conn_type configuration directly in mt7615_mcu_set_sta_rec and
remove sta_rec_convert_vif_type since it is actually used just in
mt7615_mcu_set_sta_rec
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When loading EEPROM data from flash, the RF frontend settings need to be
initialized from flash data. Without this, the chip loads the wrong values
from its internal eFuse ROM.
Signed-off-by: Felix Fietkau <[email protected]>
Now that tx status reporting can figure out the first attempted rate, we can
make switching from lower rates to higher rates more conservative.
This reduces retries under bad link conditions and ensures that fallback
rates get more test coverage
Signed-off-by: Felix Fietkau <[email protected]>
Tx status reporting on mt7603 has a number of issues:
- the hardware can alter the first rate index, but it is not reported to
the driver
- probing is very imprecise, because it alters the per-client rate set,
but only considers info->status.rates for rate selection of a single probe
packet
- short/long GI selection has limitations, which are not accurately reported
to mac80211
- if rates are changed while packets are in flight, tx status reports for
the old rate set might be processed based on the new selection
This led to very suboptimal rate selection with minstrel_ht.
This patch completely reworks tx status reporting to get rid of these
limitations:
- Store the previous and current rate set in the driver + the TSF value
at the time of the switch.
- Use the tx status TSF value to determine which rate set needs to be used
as reference.
- Report only short or long GI rates for a single status event, not a mix.
- The hardware reports the last used rate index. Use it along with the
retry count to figure out what rate was used for the first attempt.
- Use the same retry count value for all rate slots to make this calculation
work.
- Derive the probe rate from the current rateset instead of the skb cb
- Do not wait for a status report for the probe frame before removing the
probe rate from the rate table. Do it immediately after it was referenced
in a tx status report.
- Use the first half of the first rate retry budget for the probe rate
in order to avoid using too many retries on that rate
With this patch, throughput under bad link conditions is improved
significantly, and there is a lot less rate fluctuation going on.
Signed-off-by: Felix Fietkau <[email protected]>
This didn't bring the performance benefit that I had hoped for, so the mac80211
patch for this will not make it upstream
Signed-off-by: Felix Fietkau <[email protected]>
Set usb buffer size taking into account skb_shared_info in order to
not always copy the first part of received frames if A-MSDU is enabled
for SG capable devices
Signed-off-by: Lorenzo Bianconi <[email protected]>
Commit f8f527b16db5 ("mt76: usb: use EP max packet aligned buffer sizes
for rx") breaks A-MSDU support. When A-MSDU is enable the device can
receive frames up to q->buf_size but they will be discarded in
mt76u_process_rx_entry since there is no enough room for
skb_shared_info. Fix the issue reallocating the skb and copying in the
linear area the first 128B of the received frames and in the frag_list
the remaining part.
Fixes: f8f527b16db5 ("mt76: usb: use EP max packet aligned buffer sizes for rx")
Signed-off-by: Lorenzo Bianconi <[email protected]>
