Move hw data queues in mt76_phy from mt76_dev since mt7915 supports per
phy hw queues in dbdc mode
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mcu queue to a dedicated array q_mcu in mt76_dev structure.
This is a preliminary patch to move data queues in mt76_phy and properly
support dbdc
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt76_init_mcu_queue utility routine in order to allocate
dedicate q_mcu pointers for mcu hw queues. This is a preliminary patch
to move data queues in mt76_phy and add dbdc support to mt7915 driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to move data queues in mt76_phy and properly
support dbdc
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_init_tx_queue in mac80211.c since it is shared by all
drivers.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The ring is used for looping back tx powersave filtered frames, so it could
use some more room, in case more than one aggregate was queued
Signed-off-by: Felix Fietkau <[email protected]>
Before extracting the tid out of the packet, check if it was qos-data.
Only accept tid values 0-7
Also, avoid accepting the hardware queue as skb queue mapping, it could
lead to an overrun. Instead, derive the hardware queue from the tid number,
in order to avoid issues with packets being filtered multiple times.
This also fixes a mismatch between hardware and software queue indexes.
Signed-off-by: Felix Fietkau <[email protected]>
Remove unnecessary mcu queue initialization in mt7603_dma_init since it
has been already done in mt76_mmio_init
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76{15,03}_tx_tasklet in mt76_alloc_device in order to be used as
default tx_tasklet initialization. Remove duplicated code in
mt7603/mt7615 drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This fixes the following checkpatch warnings:
WARNING: Improper SPDX comment style
CHECK: No space is necessary after a cast
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move netif_napi_del in mt76_dma_cleanup routine since it is done
by all drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This allows tx scheduling and tx cleanup to run concurrently
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt76_sw_queue data structure in order to support new
chipsets (e.g. mt7615) that have a shared hardware queue for all traffic
identifiers. mt76_sw_queue will be used to track outstanding packets
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76x02_init_tx_queue and mt76x02_init_rx_queue in mt76
module in order to be reused adding support for mt7603 driver
and remove duplicated code.
Squash mt76x02_init_tx_queue and mt76x02_init_rx_queue in
mt76_dma_alloc_queue
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use PSE registers to loop back any pending tx packets for a client that
just went to sleep back into the MCU rx queue.
Re-queue those packets to the tx queue immediately after a client wakes up.
Signed-off-by: Felix Fietkau <[email protected]>
Use mt76x02_dev data structure as reference in mt76x02_mmio.c
instead of mt76_dev
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
